teves VOLKSWAGEN PASSAT 1995 B3, B4 / 3.G Service Workshop Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1995, Model line: PASSAT, Model: VOLKSWAGEN PASSAT 1995 B3, B4 / 3.GPages: 369, PDF Size: 12.33 MB
Page 4 of 369
Downloaded from www.Manualslib.com manuals search engine Rear axle, servicing (four wheel drive vehicles)
Rear drive shafts, servicing
Reworking cap nut in side member (four wheel drive vehicles)
Suspension strut, disassembling and assembling (four wheel drive
vehicles)
Wheel bearings, servicing - disc brakes (four wheel drive vehicles)
44 - Wheels, Tires, Wheel alignment
Vehicle alignment
Test requirements:
Vehicle alignment specifications (front wheel drive vehicles)
Vehicle alignment specifications (four wheel drive vehicles)
Front wheel camber, adjusting
Calculating the direction of travel:
45 - Anti-lock brake system
Anti-locking Brake System (ABS) and Anti-locking Brake System with
Electronic Differential Lock (ABS/EDL) Teves 04
Notes for repair work on ABS, ABS/EDL
Control module, removing and installing
Wheel speed sensor and rotor for speed sensor, removing and installing
Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock
(ABS/EDL), Teves 20 GI
Safety precautions
ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master
cylinder (Teves 20 GI), servicing
ABS hydraulic unit and ABS control module (Teves 20 GI), removing and
installing
Brake hydraulic system, bleeding and filling
Assembly overview - hydraulic unit, brake servo/brake master cylinder
Hydraulic unit, removing and installing
Brake Pedal Position Sensor, removing and installing
46 - Brakes - Mechanical components
Front brakes, servicing (Girling caliper)
Brake pads, removing and installing
Page 5 of 369
Downloaded from www.Manualslib.com manuals search engine Front brakes, servicing (Teves/Ate)
Brake pads, removing and installing
Rear wheel brakes, servicing (drum brakes)
Brake shoe adjustment, releasing
Rear wheel brakes, servicing
Brake shoes, removing and installing
Parking brake, adjusting (drum brakes)
Rear wheel brakes, servicing (disc brakes)
Girling rear wheel disc brakes (front and four wheel drive vehicles)
Brake pads, removing and installing
Parking brake, adjusting (disc brakes)
Parking brake lever assembly overview
Brake pedal/brake servo, removing and installing
Brake pedal, removing and installing
Brake Light Switch, adjusting
47 - Brakes - Hydraulic components
Assembly overview: brake master cylinder/brake servo
Girling front brake caliper, servicing
Front brake caliper pistons, removing and installing
Front brake caliper, servicing (Teves/Ate)
Rear brake caliper, servicing
Rear brake caliper piston, removing and installing
Pre-bleeding brake caliper
Brake pressure regulator, checking and adjusting
Vehicles without ABS, vehicles with ABS, ABS/EDS, Teves 04
Load dependent brake pressure regulator specifications
Adjusting regulator
Brake system, bleeding
Brake system, bleeding (vehicles with and without ABS, ABS/EDL)
Brake system, bleeding (with pressure bleeder VAS 5234)
Brake system, bleeding (without pressure bleeder)
Page 170 of 369
Downloaded from www.Manualslib.com manuals search engine 45-1
Anti-locking Brake System
(ABS) and Anti-locking Brake
System with Electronic
Differential Lock (ABS/EDL)
Teves 04
The ABS, ABS/EDL brake system is divided
diagonally. The servo-assist is effected
pneumatically, by the vacuum brake servo unit.
Located between the brake master cylinder and
the vacuum servo unit is a mounting bracket for
the hydraulic unit with pump.
The hydraulic unit together with pump, supplies
only the anti-locking brake system (ABS) or anti-
locking brake system and traction control system
(ABS/EDL).
Malfunctions on the ABS, ABS/EDL systems do
not influence the brake system and servo. The
vehicle can be driven without the ABS, ABS/EDL
functions operating. Page 1 of 5Anti-locking Brake System (ABS) and Anti-locking Brake System with Electronic Differential Lock (A...12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.1
Page 175 of 369
Downloaded from www.Manualslib.com manuals search engine 45-6
Anti-lock Brake System (ABS)
and ABS with Electronic
Differential Lock (ABS/EDL),
Teves 20 GI
General information The ABS or ABS/EDL braking system is divided
diagonally. Brake pedal pressure is boosted
pneumatically, by the vacuum brake booster.
Vehicles with Teves 20 GI ABS or ABS/EDL do not
have a mechanical brake pressure regulator.
Specially matched software in the ABS control
module regulates rear axle brake pressure. The ABS hydraulic unit -a- and ABS control module -
b- together make up one component. Separating
them for service is only possible after the assembly
has been removed.
New ABS control units supplied as replacement parts
from the Parts department are not coded, and require
coding after installation:
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01
Malfunctions of the ABS or ABS/EDL system do not
influence the brake system or the vacuum brake
booster. The conventional brake system remains
functional even without ABS.
Before working on the ABS or ABS/EDL system,
determine the cause of the malfunction using the On
Board Diagnostic (OBD) program % Repair Manual,
ABS & ABS/EDL On Board Diagnostic. Page 1 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2
Page 176 of 369
Downloaded from www.Manualslib.com manuals search engine 45-7
Safety precautions
WARNING!
Brake fluid is poisonous.
CAUTION!
Before working on the ABS or ABS/EDL
system, disconnect the battery Ground
(GND) strap. For anti-theft coded radios, first
make sure that the radio code is available.
Brake fluid must not contact painted parts. Brake fluid absorbs moisture from the air
and must therefore be replaced every two
years. Use only new, approved brake fluid
that complies with MVSS 116 DOT 4.
DO NOT use silicone-brake fluid (DOT 5).
Even the smallest traces can cause sever
corrosion in the brake system.
Before doing any welding repairs on the
vehicle using electric welding equipment,
disconnect the ABS control module.
After work that requires opening the brake
hydraulic system, bleed the system Page 47-29 . Page 2 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2
Page 177 of 369
Downloaded from www.Manualslib.com manuals search engine 45-8
CAUTION!
During the final road test, make sure that at
least one controlled brake test is included
(pulsations must be felt at the brake pedal).
Absolute cleanliness is required when
working on the ABS or ABS/EDL system. DO
NOT use any products that contain mineral
oil, such as oils, greases, etc.
Thoroughly clean all connections and the
immediate vicinity before loosening. DO NOT
use aggressive cleaning agents such as
brake cleaner, gasoline or thinners.
Place removed parts on a clean surface and
cover. DO NOT use fluffy cloths.
Carefully seal or cover opened components
if a repair cannot be completed immediately.
After separating the ABS hydraulic unit and
ABS control module, always use the plastic
foam transportation protection for the valve
dome, and always use the sealing plug kit
Part No. 1 H0 693 311 A.
Only install replacement parts that were
packed in their original packaging. Only
remove them immediately before installation. When the hydraulic system is open DO NOT
work with compressed air in the vicinity and
DO NOT move the vehicle.
Take precautions to make sure that brake
fluid does not enter any wiring harness
connectors. Page 3 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2
Page 178 of 369
Downloaded from www.Manualslib.com manuals search engine 45-9
ABS, ABS/EDL
hydraulic unit,
vacuum brake
booster and brake
master cylinder
(Teves 20 GI),
servicing
CAUTION!
DO NOT separate the ABS
hydraulic pump from the
valve block.
1 - Brake servo (vacuum
brake booster)
2 - Brake master cylinder
3 - Brake fluid reservoir
4 - Cap
5 - Self-locking nut Always replace 25 Nm (18 ft lb) 6 - Torx socket-head
bolt T25 4 Nm (35 in lb) 7 - Torx socket-head
bolt T25 8 Nm (71 in lb) Page 1 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3
Page 179 of 369
Downloaded from www.Manualslib.com manuals search engine 45-10
8 - Rubber damper
9 - Retainer
10 - ABS hydraulic unit
11 - ABS control module
12 - Brake line connection ABS hydraulic unit to
right-front brake
caliper
13 - Brake line connection ABS hydraulic unit to
left-rear brake caliper
or wheel cylinder
14 - Brake line connection ABS hydraulic unit to
right-rear brake caliper or wheel cylinder
15 - Brake line connection ABS hydraulic unit to
left-front brake caliper
16 - Brake line Brake master cylinder
(secondary piston
circuit) to ABS
hydraulic unit
17 - Brake line Brake master cylinder
(primary piston circuit)
to ABS hydraulic unit Page 2 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3
Page 180 of 369
Downloaded from www.Manualslib.com manuals search engine 45-11
ABS hydraulic unit and ABS control
module (Teves 20 GI), removing and
installing
Carefully read and follow all cautions and
warnings Page 45-7 before beginning work.
Location
The ABS control module is bolted to the ABS
hydraulic unit, located on the left-side of the
engine compartment.
CAUTION!
Do not bend brake lines at or near the ABS
hydraulic unit.
Switch ignition OFF when disconnecting and
reconnecting the ABS control module
connector.
Part numbers are listed here for reference
only. Always check with your Parts
department for the latest information. Sealing plug kit Part No. 1H0 698 311 A:
1 - Valve dome transportation protection (plastic
foam)
2 - Sealing plugs -M10- 3 - Sealing plugs -M12- Page 3 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3
Page 181 of 369
Downloaded from www.Manualslib.com manuals search engine 45-12
After separating ABS control module from ABS
hydraulic unit, always install valve dome
transportation protection on hydraulic unit.
Warranty claims for ABS hydraulic units on which
the valve dome transportation protection was not
used will not be accepted.
Removing
CAUTION!
Determine correct radio anti-theft coding
before disconnecting the battery.
- Disconnect battery Ground (GND) strap.
- Remove coolant expansion tank and swing to
one side. Page 4 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3