battery VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Workshop Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1996, Model line: PASSAT, Model: VOLKSWAGEN PASSAT 1996 B3, B4 / 3.GPages: 369, PDF Size: 12.33 MB
Page 171 of 369
Downloaded from www.Manualslib.com manuals search engine 45-2
Notes for repair work on ABS, ABS/EDL
Before doing any repair work on the anti-locking system, determine the cause of the malfunction
using On Board Diagnostic (OBD).
Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01 Before working on the ABS, ABS/EDL system,
disconnect the battery Ground strap. On
vehicles with coded radio, obtain cooling.
When working with brake fluid, observe the
relevant safety precautions and notes Page 47-27 . After work for which the brake system had to be opened, bleed the brake system with brake filler and bleeder unit VAS 5234 Page 47-27 . During the final road test, make sure that a
controlled brake test is performed at least once
(pulsations must be felt at the brake pedal).
Absolute cleanliness is required when working
on the anti-locking brake system; it is not
permitted to use any products which contain
mineral oils, such as oils, greases etc. Page 2 of 5Anti-locking Brake System (ABS) and Anti-locking Brake System with Electronic Differential Lock (A...12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.1
Page 176 of 369
Downloaded from www.Manualslib.com manuals search engine 45-7
Safety precautions
WARNING!
Brake fluid is poisonous.
CAUTION!
Before working on the ABS or ABS/EDL
system, disconnect the battery Ground
(GND) strap. For anti-theft coded radios, first
make sure that the radio code is available.
Brake fluid must not contact painted parts. Brake fluid absorbs moisture from the air
and must therefore be replaced every two
years. Use only new, approved brake fluid
that complies with MVSS 116 DOT 4.
DO NOT use silicone-brake fluid (DOT 5).
Even the smallest traces can cause sever
corrosion in the brake system.
Before doing any welding repairs on the
vehicle using electric welding equipment,
disconnect the ABS control module.
After work that requires opening the brake
hydraulic system, bleed the system Page 47-29 . Page 2 of 3Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock (ABS/EDL), Teves 20 GI12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.2
Page 181 of 369
Downloaded from www.Manualslib.com manuals search engine 45-12
After separating ABS control module from ABS
hydraulic unit, always install valve dome
transportation protection on hydraulic unit.
Warranty claims for ABS hydraulic units on which
the valve dome transportation protection was not
used will not be accepted.
Removing
CAUTION!
Determine correct radio anti-theft coding
before disconnecting the battery.
- Disconnect battery Ground (GND) strap.
- Remove coolant expansion tank and swing to
one side. Page 4 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3
Page 192 of 369
Downloaded from www.Manualslib.com manuals search engine 45-23
Hydraulic unit, removing and installing
Note:
For easier disassembling and assembling, it is
more practical to remove the hydraulic unit
complete with brake servo and brake master
cylinder.
Removing
- Disconnect battery Ground (GND) strap.
- Separate all electrical connections on ABS
unit.
- Remove as much brake fluid as possible from
brake fluid reservoir using a suction bottle.
- Disconnect brake lines from ABS hydraulic unit
and seal threaded holes with plugs from repair
kit, Part No. 1HO 698 311.
- Remove left-hand trim under instrument
panel.
- Disconnect brake pedal from brake servo unit
Page 46-44 . Page 6 of 10Assembly overview - hydraulic unit, brake servo/brake master cylinder12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.4
Page 277 of 369
Downloaded from www.Manualslib.com manuals search engine 48-7
Airbag unit, removing and installing
Removing
- Disconnect battery Ground strap.
- Center steering wheel (wheels straight-
ahead). Installing
Install in reverse order
Note:
Only use new hex socket head bolts for airbag unit.
Tightening torque: 6.5 Nm (57 in. Ib).
CAUTION!
Make sure that no one is in the vehicle when
connecting the battery Ground strap. - Remove both socket head bolts from airbag unit. - Remove airbag unit from steering wheel and
disconnect wiring connector from airbag unit.
- After installing the airbag unit, switch on ignition
then connect battery Ground strap. Page 7 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1
Page 279 of 369
Downloaded from www.Manualslib.com manuals search engine 48-9
Installing
- Install steering wheel, install nut and tighten.
Tightening torque: 50 Nm (37 ft lb).
- Connect airbag unit connector below steering
wheel.
- Install trim panel below steering column. Make
sure that the centering ring wiring connection is
located in the recess in the trim panel.
- Connect connector in steering wheel to airbag
unit connector.
- Install airbag unit Page 48-7
Note:
Use new hex socket head bolts for airbag unit.
- After installing the airbag steering wheel first
switch on ignition, then connect battery Ground
strap.
CAUTION!
Make sure that no one is in the vehicle when
connecting the battery Ground strap. Page 9 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1