ignition VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Workshop Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1996, Model line: PASSAT, Model: VOLKSWAGEN PASSAT 1996 B3, B4 / 3.GPages: 369, PDF Size: 12.33 MB
Page 173 of 369
Downloaded from www.Manualslib.com manuals search engine 45-4
Control module, removing and installing
Location
Under the rear seat, left
Note:
Switch off ignition before disconnecting and
connecting connectors.
Removing
- Fold up rear seat.
- Press control module securing clips together
and pull out.
- To pull connector off control module, release
control module locking bar.
Installing
- Install in reverse order. - Engage connector catch in control module slots
(arrow A), press connector on (arrow B) and
secure with locking bar (arrow C). Page 4 of 5Anti-locking Brake System (ABS) and Anti-locking Brake System with Electronic Differential Lock (A...12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.1
Page 180 of 369
Downloaded from www.Manualslib.com manuals search engine 45-11
ABS hydraulic unit and ABS control
module (Teves 20 GI), removing and
installing
Carefully read and follow all cautions and
warnings Page 45-7 before beginning work.
Location
The ABS control module is bolted to the ABS
hydraulic unit, located on the left-side of the
engine compartment.
CAUTION!
Do not bend brake lines at or near the ABS
hydraulic unit.
Switch ignition OFF when disconnecting and
reconnecting the ABS control module
connector.
Part numbers are listed here for reference
only. Always check with your Parts
department for the latest information. Sealing plug kit Part No. 1H0 698 311 A:
1 - Valve dome transportation protection (plastic
foam)
2 - Sealing plugs -M10- 3 - Sealing plugs -M12- Page 3 of 9ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master cylinder (Teves 20 GI), servicing12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.45.3
Page 277 of 369
Downloaded from www.Manualslib.com manuals search engine 48-7
Airbag unit, removing and installing
Removing
- Disconnect battery Ground strap.
- Center steering wheel (wheels straight-
ahead). Installing
Install in reverse order
Note:
Only use new hex socket head bolts for airbag unit.
Tightening torque: 6.5 Nm (57 in. Ib).
CAUTION!
Make sure that no one is in the vehicle when
connecting the battery Ground strap. - Remove both socket head bolts from airbag unit. - Remove airbag unit from steering wheel and
disconnect wiring connector from airbag unit.
- After installing the airbag unit, switch on ignition
then connect battery Ground strap. Page 7 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1
Page 279 of 369
Downloaded from www.Manualslib.com manuals search engine 48-9
Installing
- Install steering wheel, install nut and tighten.
Tightening torque: 50 Nm (37 ft lb).
- Connect airbag unit connector below steering
wheel.
- Install trim panel below steering column. Make
sure that the centering ring wiring connection is
located in the recess in the trim panel.
- Connect connector in steering wheel to airbag
unit connector.
- Install airbag unit Page 48-7
Note:
Use new hex socket head bolts for airbag unit.
- After installing the airbag steering wheel first
switch on ignition, then connect battery Ground
strap.
CAUTION!
Make sure that no one is in the vehicle when
connecting the battery Ground strap. Page 9 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1