lock VOLKSWAGEN PASSAT 1996 B3, B4 / 3.G Service Workshop Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1996, Model line: PASSAT, Model: VOLKSWAGEN PASSAT 1996 B3, B4 / 3.GPages: 369, PDF Size: 12.33 MB
Page 4 of 369
Downloaded from www.Manualslib.com manuals search engine Rear axle, servicing (four wheel drive vehicles)
Rear drive shafts, servicing
Reworking cap nut in side member (four wheel drive vehicles)
Suspension strut, disassembling and assembling (four wheel drive
vehicles)
Wheel bearings, servicing - disc brakes (four wheel drive vehicles)
44 - Wheels, Tires, Wheel alignment
Vehicle alignment
Test requirements:
Vehicle alignment specifications (front wheel drive vehicles)
Vehicle alignment specifications (four wheel drive vehicles)
Front wheel camber, adjusting
Calculating the direction of travel:
45 - Anti-lock brake system
Anti-locking Brake System (ABS) and Anti-locking Brake System with
Electronic Differential Lock (ABS/EDL) Teves 04
Notes for repair work on ABS, ABS/EDL
Control module, removing and installing
Wheel speed sensor and rotor for speed sensor, removing and installing
Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock
(ABS/EDL), Teves 20 GI
Safety precautions
ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master
cylinder (Teves 20 GI), servicing
ABS hydraulic unit and ABS control module (Teves 20 GI), removing and
installing
Brake hydraulic system, bleeding and filling
Assembly overview - hydraulic unit, brake servo/brake master cylinder
Hydraulic unit, removing and installing
Brake Pedal Position Sensor, removing and installing
46 - Brakes - Mechanical components
Front brakes, servicing (Girling caliper)
Brake pads, removing and installing
Page 7 of 369
Downloaded from www.Manualslib.com manuals search engine 00-1
Suspension, Wheels, Brakes, Steering
Technical data Model
Sedan/Wagon and syncro Base
Suspension 1)
Sedan/Wagon and syncro Base
Suspension 2)
Wheelbase mm 2625 2625
Track, unladen mm 1479 front, wheel offset 38
1422 rear, wheel offset 38
1485 front, wheel offset 35
1428 rear, wheel offset 35
1489 front, wheel offset 33 3)
1432 rear, wheel offset 3)
1485 front, wheel offset 35
1441 rear, wheel offset 35
1489 front, wheel offset 33 3)
1445 rear, wheel offset 33 3)
Turning circle m 10.7 11.5
Steering roll radius
(negative) mm 0.5 with offset 35
3.5 with offset 38 12 with offset 35
15 with offset 38
Wheel lock angle inner
outer 42
36 3745'
34 30' 1)
Base Suspension, explanation Page 40-1 2)
Plus Suspension, explanation Page 40-26 3)
Syncro Page 1 of 8Suspension, Wheels, Brakes, Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.00.1
Page 8 of 369
Downloaded from www.Manualslib.com manuals search engine 00-2
Steering Model
Sedan/Wagon and syncro
Suspension version
Base Suspension
Plus Suspension
Steering gear Power assisted steering gear Power assisted steering gear
Steering wheel turns from lock to lock 3.33 3.14
Overall steering ratio 17.5:1 16.4:1
Wheel alignment specifications Page 44-2 Page 2 of 8Suspension, Wheels, Brakes, Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.00.1
Page 16 of 369
Downloaded from www.Manualslib.com manuals search engine 40-2
Sub-frame, stabilizer bar
and control arm (Base
suspension)
Note: If a vehicle has to be
moved after removing the
drive shaft, first install outer joint and tighten to 50 Nm (37 ft lb) otherwise the
wheel bearing will be
damaged. Specifications for wheel
alignment Page 44-2 . Welding and straightening
operations are not
permitted on load bearing
suspension components or
those components which
locate the wheels. Always replace self-locking
nuts. Always replace corroded
nuts/bolts. Page 2 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 17 of 369
Downloaded from www.Manualslib.com manuals search engine 40-3
1 - Hex bolt, 35 Nm (26 ft
lb)
2 - Ball joint Checking Page 40-10 Check rubber boot for
damage and if necessary, replace ball joint Mark installation
position. If replaced
set to center of
elongated hole and
check toe Elongated holes are
not for camber
adjustment. Failure to observe this instruction may result in damage
to drive shafts!
3 - Captive lock nuts
4 - Air deflector plate Secured to control arm by clip
5 - Control arm Page 3 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 19 of 369
Downloaded from www.Manualslib.com manuals search engine 40-5
Repair Manual, Engine
Mechanical, Repair Group 10 12 - Connecting link
mounting Conical side toward
control arm
13 - Washer Collar faces away from mounting
14 - Self-locking hex nut, 25 Nm (18 ft lb)
15 - Sub-frame Removing and
installing with
assemblies installed:
supporting assemblies
Fig. 5 Remove sub-frame
from below with VAG
1383 (with control arm
but without steering
gear). After installing
check position of
steering wheel and
align front end. Aligning engine-
transmission assembly Page 5 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 20 of 369
Downloaded from www.Manualslib.com manuals search engine 40-6
16 - Hex bolt, 65 Nm (48 ft
lb)
17 - Stabilizer bar mounting 18 - Stabilizer bar
19 - Stabilizer bar clamp
20 - Hex bolt, 25 Nm (18 ft
lb) To secure stabilizer
bar
21 - Vibration damper Note installation
position, large part
must protrude from
sub-frame
22 - Self-locking hex nut, 25 Nm (18 ft lb)
23 - Cap nut Repairing in side
member Page 40-11 Page 6 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 28 of 369
Downloaded from www.Manualslib.com manuals search engine 40-14
Wheel bearing,
suspension strut and
drive shaft, removing and
installing (Base running
gear)
Note: If a vehicle has to be
moved after removing the
drive shaft, first install outer joint and tighten to 50 Nm (37 ft lb) otherwise the
wheel bearing will be
damaged. Welding and straightening
operations are not
permitted on load bearing
suspension components or
those components which
locate the wheels. Always replace self-locking
nuts. Always replace corroded
nuts/bolts. Wheel bolt tightening
torque: 110 Nm (81 ft lb). Page 14 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 29 of 369
Downloaded from www.Manualslib.com manuals search engine 40-15
Repair Manual, Suspension, Wheels, Brakes, Steering, Repair Group 00 1 - Self-locking nut, 265
Nm (195 ft lb) Only loosen and tighten with the vehicle standing on its wheels
(danger of accident) Any paint residue
and/or corrosion on
the thread of the outer
joint must be removed
before the nut is
installed
2 - Washer
3 - Brake disc Application 4 - Brake caliper Do not loosen brake
hose when working on
front suspension Hang up with wire or
similar
5 - Hub Pressing out Fig. 3 Pressing in Fig. 8 Pulling off bearing
inner race Fig. 5 Page 15 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 30 of 369
Downloaded from www.Manualslib.com manuals search engine 40-16
6 - Speed sensor rotor Only on vehicles with
ABS
7 - Hex bolt, 10 Nm (7 ft lb) 8 - Splash plate
9 - Circlip Ensure correctly
seated
10 - Wheel bearing Pressing out Fig. 6 Replace, as it is
destroyed during
pressing out Pressing in Fig. 7 11 - Self-locking hex nut, 35 Nm (26 ft lb)
12 - Wheel bearing housing 13 - Self-locking hex nut, 50 Nm (37 ft lb)
14 - Hex bolt Clamping bolt for ball
joint Page 16 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1