transmission VOLKSWAGEN PASSAT 1997 B3, B4 / 3.G Service Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 48-17
Instead of plastic sealing plugs a plug consisting of
Part No.113 301 229 A and banjo bolt, Part No. N
904 674 01 can be used. But when using these,
several 16 mm diameter sealing rings must be used
so that the holes in the banjo bolt are sealed. - Support engine/transmission assembly with 10-
222 A and 10-222 A/1 (support VR6 engine with
10-222A and 10-222A/3).
- Remove boot from seat on steering gear. - Remove subframe bolts. - Lower engine/transmission assembly; this will pull
the two halves of the universal joint apart.
- Disconnect hoses from steering gear and seal with plastic bag and adhesive tape.
- Seal power steering gear threaded holes with
plastic sealing plugs.
- Remove steering gear securing nuts (bolts remain
in subframe).
- Remove steering gear rearward. Page 17 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-18

Installing
Install in reverse order.

- Check position of steering wheel and, if
necessary, align front end.

Note: Tightening torques: When lifting the engine/transmission assembly
guide the lower half of the universal joint shaft -A-
into the upper half -B- at the same time (second
mechanic necessary). Coat boot with lubricant, e.g. soft soap, before
pulling onto steering gear.
Universal joint shaft 25 Nm (18 ft lb) halves
Steering gear 30 Nm (22 ft lb)
Tie rod joint 35 Nm (26 ft lb)
Subframe front and rear
70 Nm (52 ft lb) and turn 90 further Rear subframe bracket 65 Nm (48 ft lb) Page 18 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-86

1 - Cooling line Secured to
crossmember item
9 2 - Bracket Various versions
depending on
engine/transmission Page 48-96 3 - Pressure line
4 - Suction line Hydraulic pump -
Cooling line
5 - Hose clamp, 3 Nm (27
in lb)
6 - Hydraulic pump With V-belt pulley 7 - Hydraulic pump With ribbed belt
sprocket
8 - O-ring Always replace Page 86 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-94

Assembly overview:
Pressure and cooling
lines (vehicles with VR6
engine)
Note:
Securing of pressure line
varies according to type of
transmission Fig. 1 and
Fig. 2 1 - Reservoir
2 - Suction hose Reservoir - Cooling
line
3 - Cooling line Secured to
crossmember item
8 4 - Pressure line
5 - Suction line Cooling line -
Hydraulic pump
6 - Hose clamp, 3 Nm (27
in. Ib) Page 94 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-96
Fig. 1 Pressure hose, securing (vehicles with
manual transmission) Fig. 2 Pressure hose, securing (vehicles with
automatic transmission) Page 96 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1

Downloaded from www.Manualslib.com manuals search engine 48-98

Repair Manual, Engine
Mechanics; Repair Group13
Repair Manual, Engine
Mechanics; Repair Group13
Repair Manual, Maintenance 3 - Pressure hose Attachment varies
according to type of
transmission Page 48-96 4 - Seal
5 - Banjo bolt, 30 Nm (22 ft lb)
6 - Vane pump Checking delivery
pressure Page 48-13 7 - Ribbed belts Removing Tensioning ensured by tensioning roller Belt routing Checking condition 8 - Belt pulley Page 98 of 99Steering12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.48.1