Bearing VOLKSWAGEN PASSAT 1997 B3, B4 / 3.G Service Workshop Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1997, Model line: PASSAT, Model: VOLKSWAGEN PASSAT 1997 B3, B4 / 3.GPages: 369, PDF Size: 12.33 MB
Page 3 of 369
Downloaded from www.Manualslib.com manuals search engine Suspension, Wheels, Brakes, Steering
00 - General, Technical data
Suspension, Wheels, Brakes, Steering
Technical data
Steering
Brakes
Wheels, tires
40 - Front suspension
Front Wheel Suspension, Shafts and Axle
Front suspension, servicing (Base suspension)
Sub-frame, stabilizer bar and control arm (Base suspension)
Ball joint, checking (Base and Plus suspension)
Reworking cap nut in side member (Base and Plus suspension)
Wheel bearing, suspension strut and drive shaft, removing and installing (Base
running gear)
Front suspension strut, servicing (Base and Plus suspension)
Front suspension, servicing (Plus suspension)
Sub-frame, stabilizer bar and control arm, removing and installing (Plus
suspension)
Ball joint, removing and installing (Plus running gear)
Wheel bearing and suspension strut, removing and installing (Plus suspension)
Drive shaft, removing and installing (Plus running gear)
Drive shaft, repairing
Outer constant velocity joint, checking
Inner constant velocity joint, checking
Drive shaft with tripod joint, repairing
Drive axle with triple-rotor joint, removing and installing
Drive axle with triple-rotor joint, servicing
Triple-rotor joint, disassembling
Triple-rotor joint, assembling
42 - Rear suspension
Rear Wheel Suspension, Shafts and Axle
Rear axle, servicing (vehicles with front wheel drive)
Reworking cap nut in side member (front wheel drive vehicles)
Suspension strut, disassembling and assembling (front wheel drive vehicles)
Wheel bearings, servicing
Drum brakes (front wheel drive vehicles), wheel bearings, servicing
Wheel bearings, servicing - disc brakes (front wheel drive vehicles)
Page 4 of 369
Downloaded from www.Manualslib.com manuals search engine Rear axle, servicing (four wheel drive vehicles)
Rear drive shafts, servicing
Reworking cap nut in side member (four wheel drive vehicles)
Suspension strut, disassembling and assembling (four wheel drive
vehicles)
Wheel bearings, servicing - disc brakes (four wheel drive vehicles)
44 - Wheels, Tires, Wheel alignment
Vehicle alignment
Test requirements:
Vehicle alignment specifications (front wheel drive vehicles)
Vehicle alignment specifications (four wheel drive vehicles)
Front wheel camber, adjusting
Calculating the direction of travel:
45 - Anti-lock brake system
Anti-locking Brake System (ABS) and Anti-locking Brake System with
Electronic Differential Lock (ABS/EDL) Teves 04
Notes for repair work on ABS, ABS/EDL
Control module, removing and installing
Wheel speed sensor and rotor for speed sensor, removing and installing
Anti-lock Brake System (ABS) and ABS with Electronic Differential Lock
(ABS/EDL), Teves 20 GI
Safety precautions
ABS, ABS/EDL hydraulic unit, vacuum brake booster and brake master
cylinder (Teves 20 GI), servicing
ABS hydraulic unit and ABS control module (Teves 20 GI), removing and
installing
Brake hydraulic system, bleeding and filling
Assembly overview - hydraulic unit, brake servo/brake master cylinder
Hydraulic unit, removing and installing
Brake Pedal Position Sensor, removing and installing
46 - Brakes - Mechanical components
Front brakes, servicing (Girling caliper)
Brake pads, removing and installing
Page 15 of 369
Downloaded from www.Manualslib.com manuals search engine 40-1
Front Wheel
Suspension, Shafts
and Axle
Front suspension,
servicing (Base
suspension)
I - Removing and installing
subframe, stabilizer bar and
control arm (Base suspension)
Page 40-2
II - Removing and installing
wheel bearings, suspension
strut and drive shaft (Base
suspension) Page 40-14
The Base suspension is
installed in Passat 1995
vehicles up to 85 kW. Page 1 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 16 of 369
Downloaded from www.Manualslib.com manuals search engine 40-2
Sub-frame, stabilizer bar
and control arm (Base
suspension)
Note: If a vehicle has to be
moved after removing the
drive shaft, first install outer joint and tighten to 50 Nm (37 ft lb) otherwise the
wheel bearing will be
damaged. Specifications for wheel
alignment Page 44-2 . Welding and straightening
operations are not
permitted on load bearing
suspension components or
those components which
locate the wheels. Always replace self-locking
nuts. Always replace corroded
nuts/bolts. Page 2 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 24 of 369
Downloaded from www.Manualslib.com manuals search engine 40-10
Ball joint, checking (Base and Plus
suspension)
Checking axial clearance Checking radial play - Forcibly pull ball joint down and press up again. Note: - Press lower part of wheel outward and inward. There must be no perceptible or visual "play"
during either test. Observe ball joint during checks. Take into account possible existing wheel bearing
play or "play" in upper suspension strut mounting. Page 10 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 28 of 369
Downloaded from www.Manualslib.com manuals search engine 40-14
Wheel bearing,
suspension strut and
drive shaft, removing and
installing (Base running
gear)
Note: If a vehicle has to be
moved after removing the
drive shaft, first install outer joint and tighten to 50 Nm (37 ft lb) otherwise the
wheel bearing will be
damaged. Welding and straightening
operations are not
permitted on load bearing
suspension components or
those components which
locate the wheels. Always replace self-locking
nuts. Always replace corroded
nuts/bolts. Wheel bolt tightening
torque: 110 Nm (81 ft lb). Page 14 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 29 of 369
Downloaded from www.Manualslib.com manuals search engine 40-15
Repair Manual, Suspension, Wheels, Brakes, Steering, Repair Group 00 1 - Self-locking nut, 265
Nm (195 ft lb) Only loosen and tighten with the vehicle standing on its wheels
(danger of accident) Any paint residue
and/or corrosion on
the thread of the outer
joint must be removed
before the nut is
installed
2 - Washer
3 - Brake disc Application 4 - Brake caliper Do not loosen brake
hose when working on
front suspension Hang up with wire or
similar
5 - Hub Pressing out Fig. 3 Pressing in Fig. 8 Pulling off bearing
inner race Fig. 5 Page 15 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 30 of 369
Downloaded from www.Manualslib.com manuals search engine 40-16
6 - Speed sensor rotor Only on vehicles with
ABS
7 - Hex bolt, 10 Nm (7 ft lb) 8 - Splash plate
9 - Circlip Ensure correctly
seated
10 - Wheel bearing Pressing out Fig. 6 Replace, as it is
destroyed during
pressing out Pressing in Fig. 7 11 - Self-locking hex nut, 35 Nm (26 ft lb)
12 - Wheel bearing housing 13 - Self-locking hex nut, 50 Nm (37 ft lb)
14 - Hex bolt Clamping bolt for ball
joint Page 16 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 32 of 369
Downloaded from www.Manualslib.com manuals search engine 40-18
21 - Self-locking hex nut, 60 Nm (44 ft lb) Loosening and
tightening Fig. 1 22 - Stop
23 - Suspension strut
bearing
24 - Suspension strut Removing and
installing Fig. 1 and
Fig. 2 Disassembling and
assembling Page 40-23 25 - Bracket
26 - Hex bolt
27 - Tie rod Removing and
installing Page 48-77 28 - Countersunk screw
29 - Screw Page 18 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1
Page 33 of 369
Downloaded from www.Manualslib.com manuals search engine 40-19
Fig. 1 Suspension strut to body, loosening
and tightening Note:
Camber must be adjusted each time joint is loosened. Fig. 2 Wheel bearing housing/suspension strut joint, separating Page 19 of 82Front Wheel Suspension, Shafts and Axle12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.40.1