brake light VOLKSWAGEN PASSAT 1997 B3, B4 / 3.G Service Workshop Manual
[x] Cancel search | Manufacturer: VOLKSWAGEN, Model Year: 1997, Model line: PASSAT, Model: VOLKSWAGEN PASSAT 1997 B3, B4 / 3.GPages: 369, PDF Size: 12.33 MB
Page 5 of 369
Downloaded from www.Manualslib.com manuals search engine Front brakes, servicing (Teves/Ate)
Brake pads, removing and installing
Rear wheel brakes, servicing (drum brakes)
Brake shoe adjustment, releasing
Rear wheel brakes, servicing
Brake shoes, removing and installing
Parking brake, adjusting (drum brakes)
Rear wheel brakes, servicing (disc brakes)
Girling rear wheel disc brakes (front and four wheel drive vehicles)
Brake pads, removing and installing
Parking brake, adjusting (disc brakes)
Parking brake lever assembly overview
Brake pedal/brake servo, removing and installing
Brake pedal, removing and installing
Brake Light Switch, adjusting
47 - Brakes - Hydraulic components
Assembly overview: brake master cylinder/brake servo
Girling front brake caliper, servicing
Front brake caliper pistons, removing and installing
Front brake caliper, servicing (Teves/Ate)
Rear brake caliper, servicing
Rear brake caliper piston, removing and installing
Pre-bleeding brake caliper
Brake pressure regulator, checking and adjusting
Vehicles without ABS, vehicles with ABS, ABS/EDS, Teves 04
Load dependent brake pressure regulator specifications
Adjusting regulator
Brake system, bleeding
Brake system, bleeding (vehicles with and without ABS, ABS/EDL)
Brake system, bleeding (with pressure bleeder VAS 5234)
Brake system, bleeding (without pressure bleeder)
Page 239 of 369
Downloaded from www.Manualslib.com manuals search engine 46-43
16 - Securing clip Ensure seated
securely
17 - Brake Light Switch Adjusting Page 46-45 Page 7 of 9Parking brake lever assembly overview12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.6
Page 241 of 369
Downloaded from www.Manualslib.com manuals search engine 46-45
Brake Light Switch, adjusting
Note:
The Brake Light Switch must be removed for
adjusting.
- Remove trim under instrument panel.
- Disconnect harness connector for Brake Light
Switch.
- Remove Brake Light Switch by turning to right
through 90.
- Pull Brake Light Switch plunger fully out.
- Depress brake pedal as far as possible by hand,
guide Brake Light Switch through the locating
hole and secure by turning through 90to left.
- Pull brake pedal back up by hand to stop (Brake
Light Switch is pushed back by one notch).
- Connect harness connector for Brake Light
Switch
- Check function of Brake Light Switch.
- Install instrument panel trim. Page 9 of 9Parking brake lever assembly overview12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.46.6
Page 243 of 369
Downloaded from www.Manualslib.com manuals search engine 47-2
6 - Brake servo On gas engines the
vacuum required is
taken from the intake
manifold. On Diesel engines an
exhauster is installed
to create the required
vacuum. Functional check - With engine
switched off,
depress brake pedal
firmly several times
(to exhaust the
vacuum in the unit).
- Now depress brake
pedal with average
foot pressure, hold
and start engine. If
the servo unit is working properly, the pedal will be felt to
give slightly under
foot (servo
assistance becomes
effective). If faulty replace
complete. Check valve (item 14 )
is in vacuum hose Functional check - It must be possible
to blow through in
direction of arrow.
- Blowing against the arrow the valve must seat. Page 2 of 4Assembly overview: brake master cylinder/brake servo12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.47.1
Page 252 of 369
Downloaded from www.Manualslib.com manuals search engine 47-11
6 - Brake cylinder housing 7 - Brake carrier Install on brake caliper
housing
8 - Retaining spring Install with both ends
in the drillings in brake
caliper housing
9 - Piston seal Remove using a
screwdriver Fig. 2 10 - Piston Force piston out of
brake caliper using
compressed air Fig. 1 Installing Fig. 3 and
Fig. 4 and Fig. 5 First coat the piston
lightly with brake
cylinder paste. Piston diameter 54
mm
11 - Protective seal Do not damage when
installing piston Page 2 of 5Front brake caliper, servicing (Teves/Ate)12/7/2004http://ebahn.bentleypublishers.com/vw/servlet/Display?action=Goto&type=repair&id=VW.B4.SU01.47.3