ECU VOLKSWAGEN PASSAT 2013 B8 / 6.G Owner's Manual

It is important to know where the fire extinguisher is stored, how to remove and how to use it before
you need it to put out a fire.
Please be sure to read the operating instructions and heed the other important information on the fire
extinguisher label before you have to use it in a later emergency.
Using the fire extinguisher
x Release the retaining tab on the fire extinguisher bracket upward, in the direction of the arrow
⇒ fig. 192.
x Remove the fire extinguisher from the bracket.
x Lift the lever on the fire extinguisher in the direction of the arrow (A) to break the seal on the
extinguisher canister.
x While holding the fire extinguisher upright, direct the nozzle at the source of the fire.
x Press the release in the direction of the arrow (B) to release the extinguishing agent.
x Extinguish the fire from the bottom up.
x Stop extinguishing the fire only when the flames are quenched.
x If possible, have another fire extinguisher or other extinguishing agent available in case the fire
reignites!
Installing the fire extinguisher
x Guide the fire extinguisher into the attachment straps.
x Place the fire extinguisher on the bracket.
x When locking the attachment strap, always make sure that the locking bars engage securely.
Fire extinguisher maintenance
Check the following on the fire extinguisher regularly:
x Expiration date: do not exceed the expiration date on the fire extinguisher.
x Pressure gauge: the needle ⇒ fig. 193 must be in the green area (ready for use).
x General inspection: make sure the components are secure and check for rust, dents or other
damage.
x Intact tamper-resistant seal: shows that the fire extinguisher has not been used.
WARNING
A loose fire extinguisher in the passenger can be thrown around the passenger compartment
and cause serious personal injury during hard braking, an emergency maneuver or during a
crash
x Always make sure that the fire extinguisher is properly and firmly secured in bracket
provided.

WARNING
Improper replacement of burned out headlights and other light bulbs can cause serious
personal injury.
x Stop! Always read and heed the WARNINGS before doing any work in the engine
compartment. The engine compartment of any motor vehicle is a potentially dangerous area,
and work in this area can lead to serious personal injury.
x HID – High Intensity Discharge (Xenon) headlights get power from a high voltage source
that can cause severe personal injury and even death if handled improperly.
x H7 bulbs and HID – High Intensity Discharge (Xenon) headlights are under high pressure
and can explode if handled improperly.
x Always let a burned out light bulb cool down before replacing it.
x Never replace a light bulb unless you are familiar with all of the necessary procedures. In
particular, never remove a headlight unless you know exactly how to carry out the job and
have the correct tools and light bulbs.
x If you are uncertain about what to do, have the work performed by an authorized
Volkswagen dealer, an authorized Volkswagen Service Facility, or another qualified
workshop. Serious personal injury may result from improperly performed work.
x We strongly recommend that you always have HID – High Intensity Discharge (Xenon)
headlights and H7 bulbs replaced by a qualified technician.
x Do not touch the glass of light bulbs with your bare hands. Fingerprints left on the bulb
evaporate due to the heat when the bulb is switched on and cause the reflector to “cloud.”
x There are sharp edges on and around the headlight housing in the engine compartment
and the rear light housing. Wear hand protection if you replace bulbs.
NOTICE
After replacing a headlight bulb or other light bulb, always make sure that the rubber covers or
plastic caps have been properly and securely reinstalled to help prevent water from getting
into the electrical connections and headlight housing and damaging the electrical system.
Indicator light

Please carry out each step only in the order specified:
9. Replace the burned out light bulb with a new bulb of the same type B.
10. Reinsert the bulb socket assembly in the taillight assembly. The locking tabs must latch
with an audible “click.”
11.
Carefully reinsert the taillight assembly into the opening in the luggage compartment lid.
Hold the rear light assembly with one hand in the installation position, and with the other
hand tighten the fastening screws ⇒ fig. 220 B (3).
12. Plug connector plug B (2) into the bulb socket and push red locking tab B (4) in the
direction opposite to the arrow.
13. Check the taillight assembly for proper installation and secure fit.
14. Attach the cover. The cover must latch tightly and securely into place.
15. Close the luggage compartment lid.

Different models may have different taillights, and the light bulb may be in a different location
than shown in the illustrations.