Lock unlock VOLKSWAGEN PASSAT CC 2015 1.G User Guide

Removing the rear head restraint
Unlock the backrest of the rear seat bench and fold it forward ⇒ 
Luggage compartment.
Pull the head restraint all the way up ⇒ .
If necessary, press the flat blade of the screwdriver from the vehi-
cle tool kit into the slit of the trim cap ⇒ fig. 51 (1) in the direction of
the arrow and hold it in this position.
At the same time press button (2) while a second person pulls out
the head restraint completely.
Fold the backrest of the rear seat bench back so that it locks se-
curely.
Reinstalling the rear head restraint
Unlock the backrest of the rear seat bench and fold it forward ⇒ 
Luggage compartment.
Position head restraint properly over the head restraint guides of
the respective seat backrest and insert the head restraint into the
guides.
Push the head restraint down while pressing button (2).
Fold the backrest of the rear seat bench back so that it locks se-
curely.
Adjust the head restraint according to the occupant's size ⇒  Ad-
justing the front and rear head restraints.
WARNING
Driving without head restraints or with improperly adjusted
head restraints increases the risk of serious injuries in a colli-
sion.
Always drive with the head restraints in place and properly
adjusted to help minimize the risk of neck injury in a crash.
Always reinstall head restraints as soon as possible so that
vehicle occupants are properly protected.
NOTICE
When removing or reinstalling the head restraint, take care that
the head restraint does not strike the headliner or other parts of

Memory buttons
Personal settings for the front seats and outside mirrors can be as-
signed to each memory button.
These settings can be assigned to individual remote control vehicle
keys. The settings are applied after unlocking the vehicle and opening
the driver door.
Storing driver seat settings and forward driving settings for
outside mirrors
Switch on the ignition.
Manual transmission: Shift the transmission to Neutral (N) and set
the electronic parking brake.
Automatic transmission: Shift the transmission to Park (P).
Adjust the driver seat and outside mirrors.
Press the 3%4 button for at least 1 second ⇒ fig. 57.
Press the desired memory button 1 , 2 , or 3 within 10 seconds. A
chime sounds to confirm that the setting has been stored.
Storing front passenger seat settings to the front passenger seat
memory buttons
Switch on the ignition.
Adjust the passenger seat.
Press the 3%4 button for at least 1 second ⇒ fig. 57.
Press the desired memory button 1 , 2 , or 3 within 10 seconds. A
chime sounds to confirm that the setting has been stored.
Storing passenger-side outside mirror settings for backing up
Set the electronic parking brake.
Switch on the ignition.
Shift the transmission to Neutral (N).
Briefly press the desired memory button 1 , 2 , or 3 on the outside
of the driver seat.
Shift the transmission into Reverse (R).
Adjust the passenger outside mirror to provide good visibility of the
curb, for example.
The adjusted mirror position is automatically stored and assigned
to the vehicle key used to unlock the vehicle. The preselected posi-

tion will be recalled when the key assigned to that mirror adjustment
position is used again.
The passenger-side outside mirror automatically adjusts back from
the position stored for backing up when the vehicle moves forward at
about 10 mph (15 km/h) or more or when the rotary knob is rotated
from R into a different position.
Recalling stored seat memory settings
Briefly press the appropriate memory button when the vehicle is not
moving, the ignition is switched off, and the vehicle door is open.
OR: If the ignition is switched on and the door is closed, press and
hold the appropriate memory button until the stored position is
reached.
Assigning driver seat and outside mirror settings to a vehicle
key
The memory function of all vehicle keys is disabled when the vehicle
is first delivered from the factory.
To enable vehicle key memory function:
Unlock the driver door.
Press and hold a memory button ⇒ fig. 57 until memory position is
reached.
Press and hold the unlock button 0 on the vehicle key and then
press the desired memory button at the same time within about
3 seconds. A chime sounds to confirm activation.
To disable vehicle key memory function:
Press and hold the 3%4 button.
Press and hold the unlock button 0 on the vehicle key and the de-
sired memory button at the same time within about 10 seconds. A
chime sounds to confirm deactivation.
Assigning settings to an additional vehicle key
Follow the instructions ⇒  Assigning driver seat and outside mirror
settings to a vehicle key to assign the driver seat and outside mirror
settings to the vehicle key.
Unlock the vehicle with the same vehicle key.
Adjust driver seat and outside mirrors.

Lock the vehicle with locking button 1 in the vehicle key to store
the settings.
Once the settings are stored, the driver seat and the outside mirrors
move to the stored positions whenever the vehicle is unlocked with
the 0 button on the vehicle key (or unlocked with the door handle
sensor on vehicles with Keyless Access) and the driver door is
opened. If 2 people use the vehicle, each of them should always use
the key in which his or her personal settings have been stored.
Initializing the memory seats
The memory system must be initialized by an authorized Volkswagen
dealer, an authorized Volkswagen Service Facility, or another quali-
fied workshop in certain situations, for instance, if a new driver seat is
installed.
Initializing clears all memories and assignments of the memory seats.
After that, memory buttons can be reprogrammed and assigned to a
vehicle key.
Open the driver door but do not enter the vehicle.
Adjust the seats from the outside.
Move the angle of the backrest forward as far as it will go.
Release the backrest adjustment switch and press it again until you
hear a chime sound.
Cancellation conditions when storing settings for the memory
buttons
When one of the following conditions is met, the storing process will
be cancelled:
The vehicle battery is weak or dead.
The 3%4 button is pressed again within about 10 seconds.
The seat position is readjusted within about 10 seconds after
pressing the 3%4 button.

“Coming home” Action
Switch on: – Switch off the ignition.
– Operate the headlight flasher for about
1 second
The “Coming home” lighting is switched on when
the driver door is open.
The delay period starts once the last vehicle door
or the luggage compartment lid is closed.
Switch off: – Automatically after delay period is over.
– Automatically, if a vehicle door or the luggage
compartment lid is still open about 30 seconds
after activation.
– Turn light switch to the / position.
– Switch the ignition on.


“Leaving
home”
Action
Switch on: – Unlock the vehicle if the light switch is in the !54/
position and the low-light sensor registers darkness.
Switch off: – Automatically after preset delay period is over.
– Lock the vehicle.
– Turn the light switch to the / position.
– Switch the ignition on.

Background lighting in the outside mirrors
The background lighting in the outside mirrors illuminates the area
near the doors when entering and exiting the vehicle. It is switched on
when the vehicle is unlocked, a vehicle door is opened, or the “Com-
ing home” or “Leaving home” feature is activated. If the vehicle is
equipped with a light sensor, the background lighting in the outside
mirrors is only switched on in darkness.

Turn the adjusting knob to the L position.
Adjust the left outside mirror. The right (passenger) outside mirror
will automatically adjust at the same time.
If needed, correct the position of the right mirror by turning the ad-
justing knob to the R position.
Auto-dimming outside mirror on the driver side
Some models are equipped with an auto-dimming outside mirror,
which is controlled together with the auto-dimming inside mirror ⇒ 
Inside mirror.
Memory for front passenger side mirror (when backing up)
On vehicles equipped with memory seats ⇒ page 136, Memory seats,
the passenger side mirror settings for backing up can be stored as
follows:
Choose the remote control vehicle key that will be used with the
settings about to be made.
Unlock the vehicle with that remote control vehicle key.
Set the electronic parking brake.
Switch on the ignition.
Activate the function Mirror down in the Settings - Convenience
menu.
Turn the adjusting knob for the side mirrors to the R position.
Shift the transmission into Reverse (R).
Adjust the passenger outside mirror for a clear view of the curb, for
example.
The adjusted mirror position is automatically stored and assigned
to the vehicle key used to unlock the vehicle. The preselected posi-
tion will be recalled when the key assigned to that mirror adjustment
position is used again.
Recalling passenger side mirror settings
Turn the adjusting knob for the side mirrors to the R position.
Shift the transmission into reverse gear with the ignition switched
on.
The mirror moves back to the regular position when the vehicle
moves forward faster than about 10 mph (15 km/h) or the adjusting
knob is turned to the O or L position.

WARNING
An open or unlocked luggage compartment poses special risks
for children.
Close and lock the luggage compartment lid and all doors
when the vehicle is not in use. First, make certain that no one is
left inside.
Never leave your vehicle unattended or let children play
around the vehicle, especially with the luggage compartment lid
left open. A child could crawl into the vehicle and pull the lid
shut, becoming trapped and unable to get out. This could cause
severe or fatal injuries.
A closed vehicle can become very hot or very cold, depend-
ing on the season. Temperatures can quickly reach levels that
can cause unconsciousness or death, particularly to small chil-
dren.
Never let children play in or around the vehicle.
Never let anyone ride in the luggage compartment.

Pull the release button (1) forward while folding the rear seat
backrest forward.
The rear seat backrest is unlocked when the red mark on the but-
ton (2) is visible.
The rear seat backrest is released and can be folded forward.
If the rear backrest is folded down, no one, including children, may
ride on the rear seat.
Folding the rear seat backrest forward with the release lever in
the luggage compartment
Push the head restraint all the way down ⇒  Adjusting the seating
position.
Open the luggage compartment lid ⇒  Luggage compartment lid.
Pull the remote release lever for the left ⇒ fig. 101 (1) or right (2)
rear seat backrest in the direction of the arrow. The unlocked section
of the rear seat folds forward automatically.
Close the luggage compartment lid, if necessary ⇒  Luggage com-
partment lid.
The rear seat backrest is unlocked when the red mark on the but-
ton ⇒ fig. 100 (2) is visible.
If the rear backrest is folded down, no one, including children, may
ride on the rear seat.
Folding the rear seat backrest back into place
Fold the rear seat backrest back until it engages securely ⇒ .
The red mark on the release button (2) should no longer be visible.
The rear seat backrest must be securely latched into place in order
for the safety belts on the rear seats to provide optimal protection.

If the pass-through is equipped with a lock, use the emergency key
⇒  Vehicle key set to unlock the luggage compartment pass-through.
Pull the release lever ⇒ fig. 102 and fold the pass-through cover all
the way forward.
Open the luggage compartment lid.
Slide long objects from the luggage compartment through the pass-
through.
Secure objects with the safety belt.
Close the luggage compartment lid.
Closing the pass-through
Fold the pass-through cover back until it engages securely. The red
marking on the luggage compartment side ⇒ fig. 103 (1) should not
be visible.
Close the luggage compartment lid.
If the pass-through is equipped with a lock, use the emergency key
⇒  Vehicle key set to lock the luggage compartment pass-through.
If necessary, fold the center armrest up.
The pass-through can also be opened from the luggage com-
partment. Press the release lever (1) down and push the cover for-
ward.
Tie-downs

Fig. 104 In the luggage compartment: Tie-downs.

(2) Strap indicating the location of the storage compartment handle
(3) MDI (MEDIA-IN) jack in the pull-down storage compartment
Opening and closing the glove compartment
If necessary, unlock the glove compartment with the emergency key
⇒  Vehicle key set. It is locked when the key slot is vertical.
To open, pull the handle ⇒ fig. 124.
To close, push the lid up.
Opening and closing the storage compartment for the Owner's
Manual or MDI (MEDIA-IN) jack
Depending on equipment, the storage compartment at the top of the
glove compartment is designed to hold either the Owner's Manual or
the MDI (MEDIA-IN) jack.
The Owner's Manual compartment or MDI (MEDIA-IN) jack is located
in a storage compartment at the top, which can be pulled down to
open ⇒ fig. 125 (3).
The strap (2) indicates the handle for opening the storage compart-
ment.
If the vehicle is not equipped with the MDI (MEDIA-IN) jack, always
keep the Owner's Manual in this storage compartment. To stow the
Owner's Manual, place it in the slot with the binding facing the inside
of the glove compartment door.
Holders
Depending on the model, there may be holders for a pen and a note-
pad in the glove compartment.
Cooling the glove compartment
There is an air vent (1) in the back of the glove compartment. Cool air
can be directed into the glove compartment if the air conditioner is on.
Open or close the air vent by turning it.