Parking VOLKSWAGEN T-ROC 2021 Owner´s Manual

Changing a wheel can be dangerous, especially when carried out at the side of a road. Please
observe the following steps in order to reduce the risk of serious injuries:
as soon as possible and when safe to do so. Park the vehicle at a safe distance
from moving traffic in order to carry out the wheel change.
work during the wheel change.

board or similar support for the vehicle jack.
urself when you feel confident with carrying out the procedure. If not,
seek expert assistance.

ver
to the position P or select a gear on a manual gearbox in order to reduce the risk of unintended
vehicle movement.
immediately after changing a wheel.
n the case of vehicles with a Tyre Pressure Loss Indicator, the system must be re-synchronised
immediately after a wheel change⇒ Tyre Pressure Loss Indicator .
Preparations for changing a wheel
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Checklist
The following actions must always be carried out in the given order in preparation for changing the
wheel ⇒ :

If your vehicle has a flat tyre, park the vehicle on a firm and level surface at a safe distance from
moving traffic.

Switch on the electronic parking brake Parking and manoeuvring.

DSG® dual clutch gearbox: move the selector lever to position P DSG® dual clutch gearbox.

Switch off the engine and remove the key from the ignition.

-piece wheel bolts: use only two-piece wheel bolts.
Lifting the vehicle with the jack

Fig. 205 Jacking points.

Fig. 206 Jack fitted at the rear on the left-side of the vehicle.
First read and observe the introductoryinformation and safety warnings⇒Introduction 
The jack may be positioned only at the reinforcements on the underbody, which are located behind
the markings on the body ⇒ Fig. 205 . Always use the jacking point closest to the wheel you are
working on ⇒ .
Checklist
For your own safety, carry out the following points in the specified order ⇒ :

Choose a firm and level surface suitable for lifting the vehicle.

Switch off the engine. Select a gear on vehicles with a manual gearbox or move the selector lever to
position P on vehicles with DSG® dual clutch gearbox DSG® dual clutch gearbox and switch on the
electronic parking brake Parking and manoeuvring.

Chock the wheel diagonally opposite using collapsible chocks or other suitable objects.

The air compressor from the breakdown set may be operated from the 12-volt socket, even if the
power rating on the type plate of the air compressor exceeds the maximum power rating of the
socket.
Preparations
First read and observe the introductoryinformation and safety warnings⇒Introduction 
Checklist
Always carry out the following actions in the given order ⇒ :

If your vehicle has a flat tyre, park the vehicle on a firm and level surface at a safe distance from
moving traffic.

Switch on the electronic parking brake Parking and manoeuvring.

DSG® dual clutch gearbox: move the selector lever to position P DSG® dual clutch gearbox.

Switch off the engine and remove the key from the ignition.

Manual gearbox: select a gear Manual gearbox: selecting a gear.

Ask all vehicle occupants to leave the vehicle and stand at a safe distance away from moving traffic.

Switch on the hazard warning lights and set up the warning triangle In an emergency. Observe any
legal requirements.

Check whether the puncture can be repaired with the breakdown set The tyre sealant must not be
used:.

When towing a trailer: unhitch the trailer from the vehicle and park it properly .

The Volkswagen dealership cannot be held liable for any damage caused by technical modifications
and/or work performed incorrectly.
The Volkswagen dealership is not responsible for damage caused by technical modifications and/or
work performed incorrectly. Such damage is not covered by the Volkswagen guarantee.
Volkswagen recommends that all repairs and technical modifications be performed by an authorised
Volkswagen workshop using Volkswagen Genuine Parts®.
Volkswagen repair information
Volkswagen service information and official Volkswagen repair information can be purchased for a
fee.
Customers in Europe, Asia, Australia, Africa, Central and South America: please contact a
Volkswagen dealership or qualified workshop or register with the online portal erWin (electronic
repair and workshop information):
https://erwin.volkswagen.de
erWin is available in numerous languages.
Vehicles with special body equipment or add-on parts
The manufacturers of body equipment and add-on parts must ensure that the body equipment and
add-on parts (conversions) adhere to the applicable environmental laws and regulations, particularly
the EU directive 2000/53/EC concerning end-of-life vehicles and EU directive 2003/11/EC concerning
the restrictions on the marketing and use of certain dangerous substances and preparations.
The vehicle owner should keep all assembly documentation for these conversions, and pass it on to
the disassembly company upon vehicle handover if the vehicle is scrapped. This is designed to
facilitate environmentally friendly disposal for all vehicles, including converted vehicles.
Windscreen repairs
To function properly, some items of equipment require an electrical or electronic module, which is
located on the inside of the windscreen near the interior mirror. If the windscreen has been
damaged in the viewing field of the electrical or electronic module, e.g. by stone impact, the
windscreen must be replaced. Repairing the crack can lead to malfunctions or faults in the
equipment.
After changing the windscreen, the camera and sensors must be set up and calibrated by a qualified
workshop.
Impairment or damage to sensors and cameras
Incorrectly performed repairs, structural changes to the vehicle, e.g. lowering the suspension,
retrofitted add-on parts or changes to the trim can lead to sensors and cameras being displaced or
damaged. This can also be caused by collisions, e.g. when parking, or also even by minor damage,
e.g. stone impacts on the windscreen.
Failure to observe this point may impair important functions (driver assist systems) and damage the
vehicle.

Gross combination weight rating (vehicle plus trailer)
Gross front axle weight rating
Gross rear axle weight rating
Vehicle identification number (VIN)
The vehicle identification number can be read from outside the vehicle through a viewer in the
windscreen ⇒ Fig. 216  (arrow). The viewer is located in the lower corner of the windscreen. The
vehicle identification number is also stamped on the right-hand water drainage channel. The water
drainage channel is located between the suspension turret and wing. Open the bonnet to gain
access to the vehicle identification number ⇒ In the engine compartment .
The vehicle identification number can be displayed in the Infotainment system using the button
and the and Service function buttons ⇒ Infotainment system controls and displays .
Dimensions

Fig. 217 Illustration: dimensions.
The data in the table apply to the German basic model with the basic specification.

NOTICE
Always take care when driving into parking spaces with high kerbs or fixed boundaries. Objects that
protrude from the ground can damage the bumper and other components when parking the vehicle.

when driving into
parking spaces
with high kerbs or
fixed boundaries.
Objects that
protrude from the
ground can
damage the
bumper and other
components when
parking the
vehicle.pecified
values can vary
due to different
wheel rim and tyre
sizes, additional
equipment,
different model
versions or
retrofitted
accessories, and
also for special
vehicles and
vehicles that have
been
manufactured for
other
countries. Fig. 217 :
Value
Ⓐ Width (from
exterior mirror
to exterior
mirror)
1,992
mm
Ⓑ Width 1,819
mm
Ⓒ Front track 1,538
mm –
1,546
mm
Rear track 1,533
mm –
1,541
mm

when driving into
parking spaces
with high kerbs or
fixed boundaries.
Objects that
protrude from the
ground can
damage the
bumper and other
components when
parking the
vehicle.pecified
values can vary
due to different
wheel rim and tyre
sizes, additional
equipment,
different model
versions or
retrofitted
accessories, and
also for special
vehicles and
vehicles that have
been
manufactured for
other
countries. Fig. 217 :
Value
Ⓓ Height to the
upper edge of
the roof at
kerb weighta)
1,533
mm
Height at kerb
weighta) with
navigation
aerial
1,573
mm
Height to the
roof railing at
kerb weighta)
1,552
mm
Ⓔ Length with
fitted towing
bracket (when
supplied from
4,330
mm

when driving into
parking spaces
with high kerbs or
fixed boundaries.
Objects that
protrude from the
ground can
damage the
bumper and other
components when
parking the
vehicle.pecified
values can vary
due to different
wheel rim and tyre
sizes, additional
equipment,
different model
versions or
retrofitted
accessories, and
also for special
vehicles and
vehicles that have
been
manufactured for
other
countries. Fig. 217 :
Value
factory)
Ⓕ Length (from
bumper to
bumper)
4,234
mm
Ⓖ Wheelbase 2,590
mm
Ⓗ Ground
clearance
when ready to
driveb)
between the
axles
161
mm
Ⓘ Height with
open bonnet
1,838

when driving into
parking spaces
with high kerbs or
fixed boundaries.
Objects that
protrude from the
ground can
damage the
bumper and other
components when
parking the
vehicle.pecified
values can vary
due to different
wheel rim and tyre
sizes, additional
equipment,
different model
versions or
retrofitted
accessories, and
also for special
vehicles and
vehicles that have
been
manufactured for
other
countries. Fig. 217 :
Value
and kerb
weighta)
mm
Ⓙ Height with
open boot lid
and kerb
weighta)
1,992
mm
Turning circle
diameter
Approx.
11.1 m

carefully
through dips
in the road
and over
kg 1,270