parking brake VOLVO S60 2003 User Guide

vehicle.
pg. 110 Wheels and tires
Changing wheels
Insert flat end of lug wrench and turn/pull straight out
Changing wheels
The spare wheel is located under the carpet on the trunk floor. The jack and crank are secured in the wheel recess.
There are two jack attachment points on each side of the car (see illustration on next page). To change a wheel:
Engage the parking brake.
Put the gear selector in (P)ark (automatic transmission) or reverse (manual transmission).
Loosen the wheel bolts
Remove the wheel cap (where applicable) using the lug wrench in the tool kit.
With the car still on the ground, use the lug wrench to loosen the wheel bolts 1/2 - 1 turn. Turn the bolts
counterclockwise to loosen.
CAUTION:
The car must not be driven with wheels of different dimensions or with a spare tire other than the one that came with
the car. The use of different size wheels can seriously damage your car's transmission.
Correct tightening torque on wheel bolts must be observed. The wheel bolts should never be greased or lubricated. The
extended, chromed wheel bolts must not be used with steel rims, as they make it impossible to fit the hub caps.
pg. 111 Wheels and tires
ProCarManuals.com

Attaching the jack
Position the jack correctly on the bar in the attachment (see illustration above) and crank while simultaneously
guiding the base of the jack to the ground. The base of the jack must be flat on a level, firm, non-slippery surface.
Before raising the car, check that the jack is still correctly positioned in the attachment.
Raise the vehicle until the wheel to be changed is lifted off the ground.
Unscrew the wheel bolts completely and carefully remove the wheel so as not to damage the threads on the studs.
NOTE: To avoid excessive wear and the necessity of rebalancing, mark and reinstall wheels in the same location and
position as before removal. To lessen the chance of imbalance, each wheel hub is equipped with a guide stud to ensure
that a removed wheel can be reinstalled in its original position (as when changing over to winter tires/wheels).
Installing the wheel
Clean the contact surfaces on the wheel and hub.
Lift the wheel and place it on the hub.
Install the wheel bolts and tighten hand -tight. Using the lug wrench, tighten crosswise until all bolts are snug.
Lower the vehicle to the ground and alternately tighten the bolts crosswise to 102 ft. lbs. (140 Nm).
Install the wheel cap (where applicable).
WARNING!
The jack must correctly engage the bar in the jack attachment. The car's weight must not rest on the jack attachment.
See illustration "Attaching the jack" to the left.
Be sure the jack is on a firm, level, non-slippery surface.
Never allow any part of your body to be extended under a car supported by a jack. Use the jack intended for the car
when replacing a wheel. For any other job, use stands to support the side of the car being worked on.
Apply the parking brake and put the gear selector in the ( P)ark position (or reverse on manual transmissions).
Block the wheels standing on the ground, use rigid wooden blocks or large stones. The jack should be kept well-
greased.
ProCarManuals.com

way catalytic converter or exhaust system overheating.
Remember that tampering or unauthorized modifications to the engine, the Electronic Control Module, or the vehicle
may be illegal and can cause three-way catalytic converter or exhaust system overheating. This includes:
- Altering fuel injection setting or components.
- Altering emission system components or location or removing components.
- Repeated use of leaded fuel.
NOTE: Unleaded fuel is required for cars with three-way catalytic converters.)
pg. 150 Specifications
Bulbs
Bulbs OutputSocket
Low beam 55 WH 7
High beam 55 WHB3
Fog lights, front 55 WH 1
Side indicator lamps P10 W-
Turn signals, parking lights, front 21 WPY
Turn signals, rear 21 WPY
Parking lights, rear 5 WBA 15 s
Brake light 21 WBA 15 s
Back up lights 21 WBA 15 s
Fog light/ Parking lights, rear 5 WBA 15 s
License plate lighting 5 WW 2.1x9.5 d
Courtesy lighting, front 5 WSV 8.5
Trunk lighting 5 WSV 8.5
Glove compartment lighting 2 WBA 9 s
Vanity mirror 1.2 W
12V
pg. 151 Specifications
Suspension
Wheel dimension
15"16"
Rim diameter (mm) 415440
tire side diameter(mm) 515540
Toe-in front (degrees) 0.1°± 0. 1°0.1°± 0. 1°
Toe-in rear (degrees) 0.2°+± 0.2°0.2+± 0. 2°
Toe-in front (mm) rim measurement 2.2± 0.72.3± 0.8
tire side measurement 2.7± 0.92.8± 0.9
Toe-in rear (mm) rim measurement 1.4± 1.41.5± 1.5
tire side measurement 1.8± 1.81.9± 1.9
Rear suspension
ProCarManuals.com

J
Jack65 , 111
Jump starting97
K
Keylockii
, 81
Keys68
Kickdown87
L
LED illumination32
Lighting panel30
Load carriers102
Locking71
Locking steering wheel82
Locks67
Long distance trips104
Long loads - carrying64
Low beam bulb132
Lubricants148
M
Maintenance Schedule118
Malfunction indicator light25
Manual climate control with air conditioning50
Manual transmission85
Messages in the display26
Multifilter with air quality sensor49
O
Occupant safety20
Octane rating78
Odometer22
Oil pressure25
Oil quality123
Oil viscosity123
Opening the trunk from the inside72
Opening/ locking the trunk72
P
P Park86
, 88
Paint116
Paint - color code116
Paintwork damage116
Parking brake25 , 37
Parking lamps30
Parking lights30
Pen holder62
Polishing115
ProCarManuals.com

Bulb no.Name Designation/power
1Direction indicator/parking light PY 21 W
2 Low beam H7 55 W
3 High beam HB3 55 W
4 Fog light (option) H1 55W
5 Fog light BA 5s 21 W
6 Tail/parking light BA 15s 5 W
7 Brake light BA 15s 21 W
8 Side marker light P 10 W
9 Direction indicator PY 21 W
10 Backup light BA 15s 21 W

Contents | Top of Page
ProCarManuals.com