ignition VOLVO S60 2009 Owner´s Manual

06 Starting and driving
Starting the vehicle
06``125
WARNING
Always place the gear selector in Park or in
reverse on models with a manual transmis-
sion, and apply the parking brake before
leaving the vehicle. Never leave the vehicle
unattended with the engine running.
Always open garage doors fully before star-
ting the engine inside a garage to ensure
adequate ventilation. The exhaust gases
contain carbon monoxide, which is invisible
and odorless but very poisonous
CAUTION
Automatic transmission
The engine should be idling when you move
the gear selector. Never accelerate until
after you feel the transmission engage!
Accelerating immediately after selecting a
gear will cause harsh engagement and pre-
mature transmission wear.
SelectingP or N when idling at a standstill
for prolonged periods of time will help pre-
vent overheating of the automatic transmis-
sion fluid.Do not race a cold engine immediately after
starting.
Ignition switch and steering wheel lock
0 – Locked position:
Remove the key to lock
the steering wheel
A.
I – Intermediate posi-
tion
B – "radio position":
Certain accessories,
radio, etc. on, daytime
running lights off.
II – Drive position: The
key position when driving.
The vehicle's entire elec-
trical system is con-
nected.
III – Start position:
Release the key when the
engine starts. The key
returns automatically to
the Drive position.
A chime will sound if the key is left in the
ignition and the driver's door is opened.AThe gear selector must be in the P (Park) position (automatic
transmission).BPlease be aware that leaving the key in this position will
increase battery drain.
WARNING
Never turn the key to position 0 while driving
or when the vehicle is being towed.Steering wheel lockThe steering wheel lock might be under tension
when the vehicle is parked.
Turn the steering wheel slightly to free the igni-
tion key.
In order to help reduce vehicle theft, make
sure the steering wheel lock is engaged
before leaving the vehicle.

06 Starting and drivingStarting the vehicle
06126
WARNING
Never switch off the ignition (turn the ignition
key to position 0) or remove the key from the
ignition switch while the vehicle is in motion.
This could cause the steering wheel to lock,
which would make the vehicle impossible to
steer.

06 Starting and drivingAutomatic transmission (option)
06130
P (Park)
G031105
Use this position when starting the engine or
parking the vehicle.
CAUTION
The vehicle must be stationary when posi-
tionP is selected.The parking brake should be set whenever the
vehicle is parked.
The gear selector is mechanically locked in the
P position (SHIFTLOCK). To release the gear
selector from this position, the engine must be
running (or the ignition key must be in posi-
tionII) and the brake pedal must be depressed.
WARNING
Never leave the vehicle unattended when
the engine is running. If, by mistake, the gear
selector is moved from P, the vehicle may
start moving.R (Reverse)Never engage R while the vehicle is moving.N (Neutral)Neutral - no gear engaged. Use the parking
brake.D (Drive)D is the normal driving position and should be
used as often as possible to help improve fuel
economy. The vehicle should not be moving
when shifting from R to the D position.4 (Intermediate gear)The transmission will shift automatically
between gears 4, 3, 2 or 1 from this position.
The transmission cannot shift up to D from
fourth gear.
3 (Intermediate gear)The transmission will shift automatically
between gears 3, 2 and 1 from this position.
The transmission cannot shift up to fourth gear
orD from third gear.L (Low gears)The transmission is locked in gears 1 and 2
when the selector is in this position.
NOTE
Gears4,3, or L can be used if you are driv-
ing in a mountainous area, towing a trailer
or to increase engine braking effect.
The transmission has a built-in limiter
designed to help prevent excessive engine
speeds (high rpm) when gears 4,3, or L are
selected.

06 Starting and drivingAutomatic transmission (option)
06132
Geartronic
G027997
P (Park)Use this position when starting the engine or
parking the vehicle.
CAUTION
The vehicle must be stationary when posi-
tionP is selected.The parking brake should also be set whenever
the vehicle is parked.
The gear selector is mechanically locked in the
P position (SHIFTLOCK). To release the gear
selector from this position, the engine must berunning (or the ignition key must be in posi-
tionII) and the brake pedal must be depressed.
WARNING
Never leave the vehicle unattended when
the engine is running. If, by mistake, the gear
selector is moved from P, the vehicle may
start moving.R (Reverse)Never engage R while the vehicle is moving.N (Neutral)Neutral - no gear engaged. Use the parking
brake.D (Drive)D is the normal driving position and should be
used as often as possible to help improve fuel
economy. The vehicle should not be moving
when shifting from R to the D position.
Manual shifting
G020237
Shift gate positionsYou can move the gear selector freely between
theMAN and D positions to select forward
gears while driving. Gears 3, 4, 5, and 6 (where
applicable) have a "lock-up" function which
reduces engine speed and helps save fuel.
Depress the button on the front of the gear
selector knob to move between the R, N, D,
andP positions.
NOTE
Reverse, Neutral, and Park cannot be
selected in Geartronic mode.

06 Starting and driving
Stability system
06
139
DSTC-related messages in the text
window•
"TRACTION CONTROL TEMPORARILY
OFF
" - The system has been temporarily
switched off due to high brake temperature
and will automatically switch on again
when the brakes have cooled.
•
"ANTI SKID SERVICE REQUIRED
" - the
system has been automatically disen-
gaged due to a fault. A trained and qualified
Volvo service technician should check the
system.
Symbols in the instrument panelThe Stability Control indicator light
This light indicates different condi-
tions, depending on how it illumi-
nates.
The Stability Control indicator light
illuminates for approximately 2 secondsThis indicates that the system is performing a
self-diagnostic test when the ignition is
switched on.The Stability Control indicator light
flashesThis indicates that the stability system is
actively functioning to help counteract wheel
spin and/or a skid.
The Stability Control indicator light
glows steadily"ANTI SKID SERVICE REQUIRED
" will be
displayed in the text window at the same time.
A fault is indicated in the stability system.
1. Stop the vehicle in a safe place and switch
off the engine.
2. Restart the engine.
3. If the indicator light goes out, the fault was
temporary and no further action is
required.
4. If the indicator light remains on, drive to an
authorized Volvo workshop as soon as
possible to have the system checked.
The Stability Control indicator light
glows steadilyIf "
DSTC SPIN CONTROL OFF
" is displayed
in the text window at the same time, this is a
reminder that spin control has been disabled
by the driver.
The warning symbol
The warning symbol glows
steadily yellow
The system has been temporarily switched off
due to high brake temperature. "
TRACTION
CONTROL TEMPORARILY OFF" will be dis-
played. The system will automatically switch
on again when the brakes have cooled.
WARNING
The stability system is intended to help
improve driving safety. It supplements, but
can never replace, the driver's judgement
and responsibility when operating the vehi-
cle. Speed and driving style should always
be adapted to traffic and road conditions.

06 Starting and drivingTowing
06140
Emergency towing
ABC
G028091
Front towing eyeletThe towing eyelet is located in the tool bag,
under the floor of the trunk, with the spare tire.
This eyelet must be screwed into the positions
provided on the right sides of either the front or
rear bumper (B, see illustrations).
WARNING
Do not use the towing eyelets to pull the
vehicle up onto a flat bed tow truck.
To attach the towing eyelet:A. Use a coin to pry open the lower edge of
the cover (A)
1.
B. Screw the towing eyelet (C) in place, first
by hand and then using the tire iron until it
is securely in place.
After the vehicle has been towed, the eyelet
should be removed and returned to the tool
bag. Press the cover back into position.A
B
C
G028093
Rear towing eyelet
Precautions when the vehicle is in tow•
The steering wheel must be unlocked. Turn
the ignition key to position I or II.
•
The gear selector must be in position N.
•
Maximum speed: 50 mph (80 km/h). Do not
exceed the maximum allowable towing
speed.
•
Maximum distance with front wheels on
ground: 50 miles (80 km).
•
While the vehicle is being towed, try to
keep the tow rope taut at all times.
•
The vehicle should only be towed in for-
ward direction.
1The opening in the cover may vary.

06 Starting and drivingJump starting
06142
Jump starting
G030860
Follow these instructions to jump start your
vehicle's dead battery or to jump start another
vehicle's dead battery using your vehicle.
Although your vehicle's battery is located
under the floor of the trunk, jumper cables
should be connected in the engine compart-
ment, to the points shown in the illustrations.
If the 12-volt auxiliary battery to be used is in
another vehicle, check that the vehicles are not
touching to prevent premature completion of a
circuit. Be sure to follow jump starting instruc-
tions provided for the other vehicle.
To jump start your vehicle:1. Switch off the ignition.
2. First connect the auxiliary battery positive
(+) terminal (1) to the positive (+) terminal in
your vehicle's engine compartment (2),
located under a small black plastic cover
attached to the fuse box cover, marked
with a "+" sign. Remove the cover on the
main fuse box if necessary to access this
terminal. Then connect the auxiliary bat-
tery's negative (–) terminal (3) to the ground
point in your vehicle's engine compartment
(4).
3. Start the engine in the assisting vehicle,
then start the engine in the vehicle with
dead battery.
4. After the engine has started, first remove
the negative (–) terminal jumper cable.
Then remove the positive (+) terminal
jumper cable.
WARNING
PROPOSITION 65 WARNING!
Battery posts, terminals, and related acces-
sories contain lead and lead compounds,
chemicals known to the state of California
to cause cancer and reproductive harm.
Wash hands after handling.
WARNING
•
Do not connect the jumper cable to any
part of the fuel system or to any moving
parts. Avoid touching hot manifolds.
•
Never expose the battery to open flame
or electric spark.
•
Do not smoke near the battery.
•
Batteries generate hydrogen gas, which
is flammable and explosive.
•
Battery fluid contains sulfuric acid. Do
not allow battery fluid to contact eyes,
skin, fabrics or painted surfaces. If con-
tact occurs, flush the affected area
immediately with water. Obtain medical
help immediately if eyes are affected.
•
Failure to follow the instructions for
jump starting can lead to personal
injury.

09 Maintenance and servicing
Working on your vehicle
09``187
G027252
Note the following before you begin working
on your vehicleBattery•
Ensure that the battery cables are correctly
connected and tightened.
•
Never disconnect the battery when the
engine is running (e.g. when replacing the
battery).
•
Never use a fast charger to charge the bat-
tery. The battery cables should be discon-
nected when recharging.
•
The battery contains acid that is both cor-
rosive and poisonous. It is important that
the battery is handled in an environmen-
tally friendly way. Let your Volvo dealer
assist you.
Hoisting the vehicleIf a garage jack is used to lift the vehicle, the
two jack attachments points should be used.
They are specially reinforced to bear the weight
of the vehicle. A garage jack can also be placed
under the front of the engine support frame.
Take care not to damage the splash guard
under the engine. Ensure that the jack is posi-
tioned so that the vehicle cannot slide off it.
Always use axle stands or similar structures.
If a two-post hoist is used to lift the vehicle, the
front and rear lift arm pads should be centered
under the reinforced lift plates on the inboard
edge of the sill rail (see illustration).
WARNING
The vehicle ignition system has very high
voltage!
The voltage in the ignition system is dan-
gerous!
Do not touch spark plugs, ignition cables or
the ignition coil when the engine is running
or the ignition is switched on!
The ignition should be switched off when:•
Conducting engine tests.
•
Replacing parts in the ignition system,
such as spark plugs, ignition coil, dis-
tributor, ignition cables, etc.
Belt checkCheck the belt regularly to make sure it is in
good condition and is clean. A worn or dirty belt
can cause poor cooling and low alternator out-
put as well as impair the operation of the power
steering and the air conditioning unit.
NOTE
The drive belt is equipped with a self-ten-
sioning mechanism and requires no adjust-
ment between changes.
WARNING
The engine must not be running when this
check is performed.Check coolant levelThe cooling system must be filled with coolant
and not leak to operate at maximum efficiency.
Check the coolant level regularly. The level
should be between the MAX and MIN marks
on the expansion tank. The check should be
made with particular thoroughness when the
engine is new or when the cooling system has
been drained.
Do not remove the filler cap other than for top-
ping up with coolant. Frequent removal may
prevent coolant circulation between the engine
and the expansion tank during engine warm up
and cooling.

09 Maintenance and servicingBattery
09196
CorrosiveNo smoking, no open flames,
no sparksExplosion
Replacing the battery
G028419
Ventilation hose1. Switch off the ignition and remove the key.
2. Wait at least 5 minutes after switching off
the ignition before disconnecting the bat-
tery so that all information in the vehicle's
electrical system can be stored in the con-
trol modules.
3. Remove the bolts on the retaining bracket
over the battery and lift out the bracket.
4. Fold up the plastic cover over the negative
(ground) battery terminal. or unscrew the
cover over the battery.
5. Disconnect the negative cable.6. Lift off the plastic cover if necessary and
disconnect the positive cable
7. Pull the ventilation hose from the battery.
8. Lift out the old battery.
Installing a new battery1. Put a new battery into place.
2. Put the lower retaining bracket in place and
retighten the bolt.
3. Reconnect the positive cable.
4. Press the cover for the positive battery ter-
minal into place and fold down the lid of the
plastic cover.
5. Connect the negative (ground) cable and
fold down the plastic cover if applicable.
6. Be sure that the ventilation hose is securely
connected to the battery and that the other
end of the hose is properly routed through
the ventilation opening in the floor of the
battery compartment (see the illustration).
7. Reinstall the retaining bracket over the bat-
tery and retighten the nuts.

09 Maintenance and servicing
Replacing bulbs
09``203 Replacing bulbs in the taillight cluster
3501204m
G027277
Location of bulbs
Brake lightParking light (left side)Fog light (one side)Side marker lampTurn signalBack up light
All bulbs in the taillight cluster can be replaced
from inside the trunk.1. Switch off all lights and turn ignition key to
position0.
2. Unlock and fold down the side panel to
access the bulbs.
The bulbs are located in two separate bulb
holders, an upper and a lower. Each bulb
holder has a locking pin.
Replace bulbs in the upper and lower
bulb holders as follows:1. To ease the work: disconnect the cable
from the bulb holder.2. Press the catches together and pull out the
holder.
3. Replace the bulb.
4. Reconnect the cable.
5. Close and secure the side panel.
NOTE
If the message indicating a burned out bulb
remains in the information display after the
bulb has been replaced, consult a trained
and qualified Volvo service technician.