buttons VOLVO S80 2002 User Guide

Some garage door openers may require you to do this procedure a third time to complete the training.
The programmed button on your HomeLink® Universal Transceiver
should now operate your garage door opener. The original hand -held transmitter can also be used, if necessary, to
operate the garage door.
The remaining two HomeLink® buttons can be programmed in the same way. In the event of any problems in
programming the HomeLink® Universal Transceiver, call toll-free 1-800-355-3515 (Internet: www.HomeLink.com
).
Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used in place of hand -held transmitters.
To operate, the key must be turned to the "accessory" position (II) or the engine must be running. Press the
programmed HomeLink® button to activate the garage door, driveway gate, security lighting, home security system,
etc.
Your original hand -held transmitters may, of course, be used at any time.
pg. 149 HomeLink® Universal Transceiver (option)
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three programmed buttons:
1. Turn the ignition key to the "accessory" position (II).
2. Hold down the two outside buttons on the HomeLink® Universal Transceiver for about 20 seconds, until
HomeLink®'s indicator light begins to flash.
3. Release both buttons.
The HomeLink® buttons can be reprogrammed using the procedures described on the previous pages.
Reprogramming a single HomeLink® button
1. Press and hold the desired HomeLink® button. Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after approximately 20 seconds), position the hand -held transmitter
2 to 5 in. (5 to 12 cm) away from the HomeLink® surface.
3. Press and hold the hand -held transmitter button. The HomeLink® indicator light will flash first slowly, then rapidly.
When the indicator light flashes rapidly, release both buttons.
The previously programmed device has now been erased and the new device can be activated by pressing the
HomeLink® button that has just been programmed. This procedure will not affect any other programmed HomeLink®
buttons.
NOTE:
· Retain the original transmitter(s) for future programming procedures (i.e., if you purchase a new car).
· For your own security, erase all programmed buttons on the HomeLink® Universal Transceiver when you sell your
ProCarManuals.com

..Kickdown..........72
..Specifications..........126
Automatic transmission - cold starts..........71
Auxiliary socket..........27, 34
B
Backrests, rear seat - folding..........54
Battery..........83, 129
Battery maintenance..........119 -120
Replacing the battery..........120
Ventilation hose..........120
Blinds - rear/side rear windows..........38
Booster cushion..........13, 15
Booster cushion - integrated..........13
Brake failure warning light ..........24
Brake fluid..........118, 127
Brake system..........16
Bulbs (list)..........129
Bulbs - replacing..........100-106
C
Capacities (oils and fluids)..........123
, 127
Cargo net in trunk..........53
Catalytic converters - three-way..........85
Center console - switches..........27
Center head restraint - rear seat..........3
Central locking buttons..........59
Chains - winter driving..........89
Changing wheels..........92, 93
Child booster cushion ......... 13, 15
Child restraint anchorages ........ 12
Child safety..........12 -15
Child safety locks - rear doors..........63
Climate controls..........41 - 45
Climate system - general information..........44
Clock..........23
Coat hanger..........49
Cold weather driving..........83
Combination filter..........41, 45
Coolant..........112, 127
Cooling system..........74, 127
Courtesy light..........50
Courtesy lights (front) - replacing..........106
Courtesy lights - exterior..........56
Cruise control..........29
Cup holder - opening..........52
ProCarManuals.com