key VOLVO S80 2006 Owner's Manual

NOTE:
Your car is equipped with a KEYLOCK system. When the engine is switched off, the gear selector must be in the
( P )ark position before the key can be removed from the ignition switch.
When starting in cold weather, the transmission may shift up at slightly higher engine speeds than normal until the
automatic transmission fluid reaches normal operating temperature.
CAUTION :
The engine should be idling when you move the gear selector. Never accelerate until after you feel the transmission
engage! Accelerating immediately after selecting a gear will cause harsh engagement and premature transmission wear.
Selecting P or N when idling at a standstill for prolonged periods of time will help prevent overheating of the
automatic transmission fluid.
Do not race a cold engine immediately after starting. Oil flow may not reach some lubrication points fast enough to
prevent engine damage.
WARNING!
Always place the gear selector in Park and apply the parking brake before leaving the vehicle. Never leave the car
unattended with the engine running.
Always open the garage doors fully before starting the engine inside a garage to ensure adequate ventilation. The
exhaust gases contain carbon monoxide, which is invisible and odorless but very poisonous.
* Your car is equipped with an electronic start inhibitor (immobilizer). The keys you received with your car are
specially coded. The code in the key is transmitted to an antenna in the ignition switch where it is compared to the
code stored in the start inhibitor module. The car can only be started if a properly coded key is used.
If two of the keys to your car are close together, e.g., on the same key ring, when you try to start the car, this could
cause interference in the immobilizer system and result in the car not starting. If this should occur, remove one of the
keys from the key ring before trying to start the car again.
pg. 78 Automatic transmission - five speed
P (Park)
Use this position when starting the engine or parking the car.
Never use P while the car is in motion.
The parking brake should also be set whenever the car is parked.
The gear selector is mechanically locked in the P position (SHIFTLOCK). To release the gear selector from this
position, the engine must be running (or the ignition key must be in position II) and the brake pedal must be
depressed.
ProCarManuals.com

W Winter/Wet driving mode - enhanced vehicle traction
Mode W will only function if the gear selector is in the (D)rive position.
Press the button at the base of the gear selector to engage/disengage this driving mode (see illustration).
An LED in the button will light up to indicate that W is engaged and this will also be displayed in the instrument
panel (see page 27
).
This mode may be selected for starting/moving off on slippery roads.
Kickdown
Automatic shift to a lower gear (kickdown) is achieved by depressing the accelerator pedal fully and briskly. An
upshift will occur when approaching the top speed for a particular gear or by releasing the accelerator pedal slightly.
Kickdown can be used for maximum acceleration or when passing at highway speeds.
Cold starts
When driving before the engine has reached its normal operating temperature, the transmission will shift up at slightly
higher engine speeds to heat the three-way catalytic converter as quickly as possible.
pg. 80 Automatic transmission (Geartronic)
P (Park)
Use this position when starting the engine or parking the car.
Never use P while the car is in motion.
The parking brake should also be set whenever the car is parked.
The gear selector is mechanically locked in the P position (SHIFTLOCK). To release the gear selector from this
position, the engine must be running (or the ignition key must be in position II) and the brake pedal must be
depressed.
WARNING!
Never leave the car unattended when the engine is running. If, by mistake, the gear selector is moved from P, the car
may start moving.
ProCarManuals.com

2 0 0 6
VOLVO S80
Chapter 10 - Audio systems
pg. 157 Audio systems
Introduction158
HU-650 overview159
HU-850 overview160
Audio functions HU-650/HU-850161
Radio functions HU-650/HU-850163
CD player HU-650168
Internal CD changer - HU-850169
External CD changer (option) - HU-650/HU-850170
Cassette deck HU-650171
Dolby Surround Pro Logic II HU-850172
Audio systems - specifications174
HomeLink® Universal Transceiver (option)175
pg. 158 Introduction
The audio system in your car is operated with the buttons and knobs in the system's front panel. Certain functions,
such as adjusting the volume, changing radio stations or tracks on a CD, etc, can also be controlled with the optional
steering wheel-mounted keypad.
The audio system is available in two versions:
HU-650
Features: AM/FM radio, single-disc CD player, cassette player, 4x25W output, six speakers.
HU-850
Features: AM/FM radio, integrated 6-disc CD changer, 4x50W or 4x70W output plus 25W Dolby Pro Logic II, eleven
speakers.
ProCarManuals.com

Effect channel volume - press, pull and turn
5. Selector knob for:
Stored radio stations
CD - changer (option), selecting a disc
6. Source/Menu
Press to open main menu
Turn to select FM, AM, CD,
CD changer (option), selecting a disc
7. Exit (exit the menu)
8. Scan function (automatically search for radio stations)
9. Navigations buttons (seek/change radio station or CD track)
10. CD eject
11. Dolby Pro Logic II
12. 2 channel stereo
13 3 channel stereo
14. CD slot
15. CD random play
16. AM
17. FM
18. CD player
19. Automatically search for radio stations
20. Display
pg. 161 Audio functions HU-650/HU-850
Switch on/off
Press the knob to switch on or turn off the radio.
Volume control
Turn the knob clockwise to increase volume. Volume control is electronic and does not have an end stop. If you have
a key pad in the steering wheel, increase or decrease the volume with the + or- buttons.
Volume control - ALARM
If a CD is playing when the radio receives an alarm bulletin (available in certain areas only), the CD player enters
pause mode. The bulletin is broadcast at the volume selected for this type of message.
After the bulletin has been completed, the audio system reverts to the originally selected sound source (radio or CD),
which is played at the volume that was selected for that source.
If the bulletin volume is adjusted while the bulletin is being broadcast, this new volume is saved and used for
subsequent bulletins.
Bass
Adjust the bass by pressing the button to extend the control and turning it to the left (less bass) or to the right (more
ProCarManuals.com

Selecting a sound source
The sound source (e.g. AM, FM, etc) can be selected in two ways:
· Use the sound source buttons (see the right illustrations above).
· Turn the SOURCE knob (see illustration above) to select a sound source (AM, FM, cassette, or CD). Press the knob
to select the AM or FM band of your choice.
The sound source selected will be shown in the display.
pg. 163 Audio systems HU-650/HU-850
Scan
Press the SCAN button to start the station scan function. When a station is found, scanning stops for approximately 10
seconds, after which scanning will continue.
Press the SCAN or EXIT button when a station has been found if you would like to listen to that station and to
discontinue the scan function.
Station seek up/down
Press
to start the seek function. The radio seeks the next audible station and tunes it in. Repeat the procedure
to continue the seek function.
Manual station search
Press
and hold it down. MAN will be shown in the display. The radio scans slowly in the selected direction
and will increase the scanning speed after a few seconds. Release the button when the desired frequency appears in the
display.
The frequency can be fine-tuned by short presses on the
keys.
The system will remain in manual search mode for 5 seconds after the button is released, after which it will return to
seek mode.
ProCarManuals.com

Audio system controls on the steering wheel
Steering wheel key pad (option)
If the vehicle is equipped with the key pad in the steering wheel press the right or left arrow to switch between preset
stations.
pg. 164 Radio functions HU-650/HU-850
Storing stations
1. Tune to the desired station.
2. Press the knob. Choose a number by turning the knob. Press again to store the station.
Preset
To choose a preset station, turn button to the stored number. The currently selected station is displayed.
Storing stations automatically
This function automatically searches for and stores up to 10 strong AM or FM stations in a separate memory. If more
than ten stations are found, the ten strongest ones are stored. This function is especially useful in areas in which you
are not familiar with radio stations or their frequencies.
To use the AUTO function:
1. Select radio mode using the AM or FM buttons.
2. Start the search by pressing AUTO for more than 2 seconds.
3. AUTO appears in the display and a number of stations with strong (max. 10) from the selected frequency band will
be stored in the auto-store memory. If there are no stations with sufficient signal strength, NO STATION is displayed.
4. Press the AUTO button or the arrow keys on the optional steering wheel controls briefly to select the stored stations.
ProCarManuals.com

programming the HomeLink® Universal Transceiver, call toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
Operating the HomeLink® Universal Transceiver
Once programmed, the HomeLink® Universal Transceiver can be used in place of hand -held transmitters.
To operate, the key must be turned to the "accessory" position (II) or the engine must be running. Press the
programmed HomeLink® button to activate the garage door, driveway gate, security lighting, home security system,
etc.
Your original hand -held transmitters may, of course, be used at any time.
pg. 177 HomeLink® Universal Transceiver (option)
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three programmed buttons:
1. Turn the ignition key to the "accessory" position (II).
2. Hold down the two outside buttons on the HomeLink® Universal Transceiver for about 20 seconds, until
HomeLink®'s indicator light begins to flash.
3. Release both buttons.
The HomeLink® buttons can be reprogrammed using the procedures described on the previous pages.
Reprogramming a single HomeLink® button
1. Press and hold the desired HomeLink® button. Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after approximately 20 seconds), position the hand -held transmitter
2 to 5 in. (5 to 12 cm) away from the HomeLink® surface.
3. Press and hold the hand -held transmitter button. The HomeLink® indicator light will flash first slowly, then rapidly.
When the indicator light flashes rapidly, release both buttons.
The previously programmed device has now been erased and the new device can be activated by pressing the
HomeLink® button that has just been programmed. This procedure will not affect any other programmed HomeLink®
buttons.
NOTE:
Retain the original transmitter(s) for future programming procedures (i.e., if you purchase a new car).
For your own security, erase all programmed buttons on the HomeLink® Universal Transceiver when you sell your
car.
Metallic sun protection films should not be used on any windows in a car equipped with HomeLink® Universal
Transceiver. This could interfere with the transceiver's function.

Contents | Top of Page
ProCarManuals.com

ISOFIX child seat anchors........ 19
J
Jack..........59
, 116, 117
Jump starting..........91
K
Key - removing from ignition switch..........77
Keyless entry system..........65, 66
Keyless entry system - replacing batteries..........66
Keylock..........77
Keys..........64
Kickdown..........79, 80
L
Label information..........150
Laminated side windows..........134
LATCH/ISOFIX anchors........ 19
License plate lights - replacing..........129
Lifting the car..........141
Lighting panel..........34
Load carriers..........86
Locking and unlocking the car..........64
Locking steering wheel..........38
Long distance trip..........93
Long loads..........55
Low/high beam headlights..........36
M
Maintenance service..........136
Malfunction indicator lamp..........29
Mirrors..........42
Mirrors, sideview - memory function..........42
Moonroof..........43
O
Occupant Weight Sensor (OWS)..........9, 10, 11
Octane rating..........74
Odometer..........27
Oil - engine..........92, 143, 144, 153
Oil pressure warning light ........ 28
Opening the hood..........142
Opening the trunk from the inside..........67
P
Paint touch-up..........132
Panic function (alarm)..........69
Park Assist..........83
Parking brake..........40
Parking brake reminder light..........28
ProCarManuals.com

Passenger's seat backrest - folding..........55
PI (Program Information) Seek..........165
Polishing..........134
Power moonroof..........43
Power seats..........54
Power steering - speed-sensitive..........85
Power steering fluid ........ 145, 153
Power windows..........41
R
Radio..........159, 160
Radio Broadcast Data System - RBDS..........165
Rain sensor - windshield wipers..........37
Reading lights - front/rear ........ 56
Rear door step lights - replacing..........129
Rear fog light..........29
Rear reading lights..........56
Rear seat backrests - folding..........60
Rear suspension..........154
Rear window - heated..........39
Rearview mirror..........42
Refrigerant..........50, 153
Refueling..........76
Remote keyless entry system..........65
Remote keyless entry system - replacing batteries..........66
Remote keyless entry system and sideview mirrors..........42
Remote keyless entry system and the driver's seat..........55
Replacing bulbs..........125-131
Replacing fuses..........120
Replacing the battery..........146
Replacing wiper blades..........148
Road assistance..........156
Roadholding..........85
Roof load - maximum..........151
Roof racks..........86
Run flat tires..........109
S
Safety locks - child..........71
Seat belt reminder..........3
Seat belts..........3, 4, 21
use during pregnancy..........4
Seat belts - cleaning..........135
Seats - front..........54
Self supporting run flat tires..........109
Servicing..........141
ProCarManuals.com

Trip odometer..........27
Trunk - opening from the inside..........67
Trunk - unlocking with master key..........67
Trunk lights - replacing..........130
Turn signal bulbs (front)..........126
Turn signals..........36
U
Unlocking the trunk with key..........67
Upholstery - cleaning..........135
Seat belts..........3
V
Vanity mirror lights - replacing..........128
Vehicle Event Data ........136
Vehicle Identification Number (VIN)..........150
Volvo Inflatable Curtain (VIC)..........13
Warning flashers..........39
Washer fluid reservoir..........153
Vehicle loading..........154
Ventilation..........46
Ventilation hose, battery ........146
Volumes (oils and fluids) ........153
Volvo On Call..........156
W
Warning lights..........28, 29
Warranty..........136
Washer fluid reservoir..........141
Washer fluid solvent..........92
Washing the car..........133, 134, 135
Water repellent glass..........134
Waxing..........134
Weight distribution..........85
Weights..........151
Wheels - changing..........116, 117
Wheels and tires..........102 - 117
Whiplash Protection System (WHIPS)..........15
Windows - electrically operated..........41
Windshield washer solvent ........ 92
Windshield wiper blades - replacing..........148
Windshield wipers/washers..........37
Winter driving..........92
Winter/Wet driving mode..........79, 81
Wiper blades - replacing..........148
ProCarManuals.com