warning VOLVO V50 2011 Owner´s Manual

04 Interior
Front seats
04

* Option/accessory, for more information, see Introduction.105
WARNING
•When transporting long objects, cover
sharp edges on the load to help prevent
injury to occupants. Secure the load to
help prevent shifting during sudden
stops.
•When the seat's backrest is returned to
the upright position, push and pull it to
be sure that it is securely locked in this
position.
Power seats*
The power driver's seat can be adjusted:
•If the ignition key is in position I or II.
•During a 10 minute period after the doors
have been unlocked if the door remains
open.
•If the door is closed and the ignition key is
not yet in the ignition, or if the key is in
position 0, the seat can be adjusted or dur-
ing a period of 40 seconds. The power
passenger's seat can only be adjusted if
the ignition key is in position I or II, or if the
engine is running.
Adjusting the seat
G020199
Seat adjustment controls
Seat adjustment controls 1, 2, 3, and 4 on the
side of the seat can be used to move the seat
to the position of your choice.
Move this section of the control up or down
to raise/lower the front section of the seat
cushion.
Move the control forward/rearward to
move the seat forward or rearward.
Move this section of the control up or down
to raise/lower the rear section of the seat
cushion.
Backrest tilt.
NOTE
Both front seats are equipped with head
restraints that can be adjusted vertically to
suit the height of the passenger. The upper
edge of the head restraint should be at least
on a level with the upper-most point of the
seat occupant's ear (see the section
"Adjusting the front seat head restraints" on
page 107).
NOTE
The power seats have an overload protector
that activates if a seat is blocked by any
object. If this occurs, switch off the ignition
(key in position 0) and wait for approxi-
mately 20 seconds before operating the
seat again.
Emergency stopIf the seat inadvertently begins to move, press
any of the buttons to stop the seat.

04 Interior
Front seats
04
106* Option/accessory, for more information, see Introduction.
Programming the seat memory, driver's
seat only*
G020200
Power seat memory buttons
Three different seating positions can be stored
in the seat's memory. The memory buttons are
located on the outboard side of the driver's
seat (see the illustration above). The following
example explains how memory button 1 can be
programmed. Buttons 2 and 3 can be pro-
grammed in the same way.
To program (store) a seat position in memory
button 1:
1. Adjust the seat to the desired position.
2.
Press and hold down the "M" (Memory)
button.3.
With the "M" button depressed, press
memory button 1 to store the seat's current
position.
To move the seat to the position that it was in
when memory button 1 was programmed,
press and hold down button 1 until the seat
stops moving.
As a safety precaution, the seat will stop auto-
matically if the button is released before the
seat has reached the preset position.
Central locking system remote key and
driver's seat memory
The remote key transmitter can also be equip-
ped with an optional function that controls the
electrically operated driver's seat in the follow-
ing way:
1. Adjust the seat to the desired position.
2. When you leave the car, lock it using the
remote key.
3. The next time the driver's door is unlocked
with the same remote key and that door is
opened within 2 minutes, the driver's seat
and side door mirrors will automatically
move to the position that they were in when
the doors were most recently locked with
the same remote key.
NOTE
The memory function in the remote key
operates independently the memory func-
tion in the seat.
WARNING
•Because the driver's seat can be
adjusted with the ignition off, children
should never be left unattended in the
car.
•Movement of the seat can be STOPPED
at any time by pressing any button on
the power seat control panel.
•Do not adjust the seat while driving. The
seat should be adjusted so that the
brake pedal can be depressed fully. In
addition, position the seat as far rear-
ward as comfort and control allow.
•The seat rails on the floor must not be
obstructed in any way when the seat is
in motion.

04 Interior
Front seats
04

107 Adjusting the front seat head restraints
The front seat head restraints are designed so
that they can be adjusted to two different
height positions.
NOTE
•When the vehicle leaves the factory, the
front seat head restraints will be in the
lower position.
•It is advisable to have the front seat
head restraints in the lower position if
you wish to fold down the seat's back-
rest.
The head restraints should be put in the upper
or lower position according to the height of the
occupant of the seat.
The upper edge of the head restraint should be
at least on a level with the upper-most point of
the seat occupant's ear (see illustration).
To raise or lower a head restraint:
Raising or lowering a head restraint1. Release the head restraint by pressing the
button underneath its left side, at the base
of the support (see the illustration).
2. Move the head restraint until it clicks
(locks) into the upper or lower position.
WARNING
After adjusting the head restraint, be sure
that it is securely locked in the new position
by pressing and/or pulling it.
Removing a head restraintThe front seat head restraints can be removed,
for example, when cleaning the upholstery or if
the front passenger's seat backrest is folded
down to accommodate a long load. To do so:
1. Release the head restraint by pressing the
release button underneath its left side, at
the base of the support.
2. While holding in the release button, press
the locking button at the base of the head
restraint's right support with a screw
driver, etc., and lift the head restraint until
it can be removed completely.

04 Interior
Front seats
04
108
WARNING
•If a front seat head restraint has been
removed, it must be put properly back
in place and it must lock (click) into one
of the available adjustment positions
before the seat is occupied.
•The front seat head restraints must be
in position and properly adjusted to the
height of the person sitting in the seat
when the vehicle is driven and when the
front passenger's seat is occupied.

04 Interior
Storage compartments
04
112
Storage pocket (on the rear side of the front
seats)
Compartment in door panel
Storage pocket (on the front side of the
front seat cushion)
Glove compartment
Storage compartment for e.g., CDs and
cup holders
Rear seat storage compartment and cup
holders
Storage pocket (on the front side of the
rear, center seat cushion).
WARNING
•Anchor any heavy objects to prevent
them from moving during sudden stops.
Glove compartment
G024208
The owners manual and maps can be stored
here. There are also holders for coins, pens and
fuel cards. The glove compartment can only be
locked and unlocked using the detachable key
blade from the central locking system's remote
key. See page 124 for information on removing
the key blade from the remote key, and page
131 for information about locking the glove
compartment.
Storage under the front, center armrest
G018371
There are two storage compartments under the
front, center armrest.
•Press the smaller button on the front edge
of the armrest and lift the armrest cover to
access a shallow storage compartment.
•Press the larger button and lift the entire
armrest to access a deeper compartment.

04 Interior
Rear seat
04
114
Rear seat head restraints
G020765
Adjust the head restraint vertically
Each of the rear seating positions is equipped
with a head restraint that can be adjusted ver-
tically to suit the height of the passenger. The
upper edge of the head restraint should be at
least on a level with the upper-most point of the
seat occupant's ear (see illustration).
WARNING
The center rear seat head restraint should
only be in its lowest position when this seat
is NOT occupied. When the center position
is occupied, the head restraint should be
correctly adjusted to the passenger’s
height. The upper edge of the head restraint
should be at least on a level with the upper-
most point of the seat occupant's ear.

To raise: Slide the head restraint up to the
desired height.

To lower: Press the catch at the base of the
right support and press the head restraint
down.

To remove: Pull the head restraint up far as
possible. Press the catch at the base of the
right support and pull the head restraint out
of the its holders.
WARNING
If a head restraint has been removed, it must
be put properly back in place and it must
lock (click) into one of the available adjust-
ment positions before the seat is occupied.
Folding down the rear seat backrests
G020790
Both sections of the rear seat backrest can be
folded down, together or separately, to enable
you to transport long objects. Before folding
down the rear seat backrests, the outboard
seat belts can be attached to the clothes hook
as shown in the illustration.

04 Interior
Rear seat
04

115
CAUTION
•When the backrests are folded down,
the head restraints may be damaged if
they are not removed. The center head
restraint must also be removed when
transporting heavy loads.
•To help prevent damage to the uphols-
tery when a backrest is folded down, be
sure that there are no objects on the
seat and that the seat belt is not buck-
led.
•When folding down the rear seat backr-
ests, remove the plug in the rear
12-volt socket to help avoid marks in
the upholstery.
Rear edge of seat cushion
Catch
Folding down the backrest
Location of the head restraint in the seat
cushion
To fold down one or both sections:
1. Grasp the rear edge of the seat cushion
and pull it forward.
2. Pull the catch on the upper outboard edge
of the backrest upward and forward to
release the backrest lock. A red lock indi-
cator is visible when the backrest is not
locked in the upright position.3. Fold the backrest down partially and
remove the outboard head restraints.
Press the center head restraint down com-
pletely or remove it.
4. Place the head restraints in the plastic
tubes, which are now accessible on the
under side of the seat cushions.
WARNING
The center rear seat head restraint should
only be in its lowest position when this seat
is NOT occupied. When the center position
is occupied, the head restraint should be
correctly adjusted to the passenger’s
height. The upper edge of the head restraint
should be at least on a level with the upper-
most point of the seat occupant's ear.

04 Interior
Rear seat
04
116
WARNING
•The red lock indicator is VISIBLE when
the backrest is NOT locked in position
and hidden when the backrest is cor-
rectly locked in place. When the back-
rest is in the upright position, push and
pull it to make sure that it is correctly
locked in place.
•When the rear seat is folded down, do
not place heavy objects against the
backs of the front seats. This places a
severe strain on the folded down back-
rest of the rear seat. Be sure to secure
cargo.
•Cargo must not be stacked higher than
the top of seat backs. This will reduce
the possibility of luggage, etc. becom-
ing projectiles during sudden maneu-
vers, rapid braking or an accident.

04 Interior
Cargo area
04
118
4. Release the button to lock the cargo area
cover in place.
5. Repeat this procedure on the opposite side
of the cargo area.
Check that the cargo area cover is securely in
place.
G020767
Fold the front section of the cover forward
Fold the front section of the cargo area cover
forward into the wedge-shaped grooves near
the rear seat.
Removing the cargo area cover1. Lift the forward section of the cover, fold it
rearward in the vehicle, and let it hang
freely.2. Press the button on the upper edge of the
cover forward to release the catches.
3. Lift out the end of the cargo area cover
from the retaining holes.
4. Repeat the procedure on the opposite side
of the cargo area.
NOTE
Both versions of the cargo area cover are
options that may be available for your vehi-
cle. Consult your Volvo retailer.
Cargo area net (accessory)
G020768
The Volvo V50 can be equipped with a cargo
area net made of strong nylon fabric that can
be used with the rear seat backrests in the
upright position or folded down.
The holder for the retractable net is mounted
on the rear side of the backrests.
Using the net with the backrests in the
upright position
1. From the cargo compartment, pull the net
upward.
2. Insert the net's right attachment in the rear-
most hole in the mounting bracket (see
illustration) and push it forward into the
smaller hole in the bracket to secure it in
place.
3. Pull out the spring-loaded attachment on
the left side of the net and insert it in the
bracket on the left side of the vehicle in the
same way.
WARNING
Be sure that the net is securely attached in
the mounting brackets.
Using the cargo net with the backrest
folded down
Fasten the net in the same way as described
above, using the front mounting brackets.

04 Interior
Cargo area
04
119
Retracting the cargo net1. Pull back one of the net's attachments to
the large hole in the mounting bracket.
2. Pull the attachment out of the mounting
bracket.
3. Do the same on the opposite side of the
vehicle.
4. Lower the net into its holder.
Removing the cargo net's holder1. Fold down the backrests
2. Push the holder out until it releases from its
retaining brackets.
Using the net with the cargo area cover
G020769
1. Fold the rear seat backrests forward
slightly. Begin by folding the narrower sec-
tion of the backrest.
2. Pull the cargo net up and to the rear.
3. Return the backrests to the upright posi-
tion.
Insert the net's end attachments into the
mounting brackets (see the illustration).
WARNING
The red lock indicator on the rear seat
backrests is VISIBLE when the backrest is
NOT locked in position and hidden when the
backrest is correctly locked in place. When
the backrest is in the upright position, it
must always be correctly locked in place.
Load anchoring eyelets
G014757
The eyelets in the cargo area can be used to
fasten accessory load and lashing straps, load
nets, and other load anchors.