display VOLVO V60 2011 Owner's Guide
[x] Cancel search | Manufacturer: VOLVO, Model Year: 2011, Model line: V60, Model: VOLVO V60 2011Pages: 388, PDF Size: 9.32 MB
Page 119 of 388
03 Your driving environment
Gearboxes
03
* Option/accessory, for more information, see Introduction.119
Deactivating the automatic gear selector
inhibitor
If the car cannot be driven, e.g. due to a flat
battery, the gear selector must be moved from
the P position so that the car can be moved.
Lift the rubber mat in the compartment
behind the centre console and open the
hatch.
Fully insert the key blade. Press the key
blade down and hold (For information on
the key blade, see page 52.)
Move the gear selector from the P position.
Automatic gearbox, Powershift*2
D: Automatic gear positions. M (+/–): Manual gear
positions.
Powershift is a six-stage automatic gearbox
that has double mechanical clutch discs in
contrast to a conventional automatic gearbox.
A conventional automatic gearbox has a
hydraulic torque converter that transfers power
from the engine to the gearbox.
Powershift transmission operates in the same
way and has similar controls and functions as
the Geartronic automatic transmission, descri-
bed in the previous section.
HSAThe HSA (Hill Start Assist) function means that
the pressure in the brake system remains forseveral seconds while the foot is moved from
the brake pedal to the accelerator pedal before
setting off or reversing uphill.
The temporary braking effect releases after
several seconds or when the driver acceler-
ates.
To bear in mindThe transmission's double clutch has overload
protection that is activated if it becomes too
hot, e.g. if the car is held stationary with the
accelerator pedal on an uphill gradient for a
long time.
Overheated transmission causes the car to
shake and vibrate, and the warning symbol illu-
minates and the information display shows a
message. The transmission can also overheat
during slow driving in queues (10 km/h or
slower) on an uphill gradient, or with a trailer
hitched. The transmission cools down when
the car is stationary, with foot brake depressed
and the engine running at idling speed.
Overheating during slow driving in queues can
be avoided by driving in stages: Stop the car
and wait with your foot on the brake pedal until
there is a moderate distance to the traffic
ahead, drive forward a short distance, and then
2Only 4-cyl. model 2.0T.
ProCarManuals.com
Page 120 of 388
03 Your driving environment
Gearboxes
03
120
wait another moment with your foot on the
brake pedal.
IMPORTANT
Use the foot brake to hold the car stationary
on an uphill gradient - do not hold the car
with the accelerator pedal. The gearbox
could then overheat.
Text message and actionIn some situations the display may show a
message at the same time as a symbol is illu-
minated.
SymbolDisplayDriving characteristicsAction
Transm. overheat brake to holdDifficulty in maintaining even speed at con-
stant engine speed.Transmission overheated. Keep the car
stationary using the foot brake.A
Transm. overheat park safelySignificant pulling in the car's traction.Transmission overheated. Park the car
immediately in a safe manner.A
Transm. cooling let engine runNo drive due to overheated gearbox.Transmission overheated. For fastest cool-
ing: Run the engine at idling speed with the
gear lever in the N or P position until the
message clears.
AFor fastest cooling: run the engine at idling speed with the gear lever in the N or P position, until the message clears.
The table shows three steps with an increased
degree of seriousness should the transmission
become too hot. In parallel with the display text
the driver is also advised that the car's elec-
tronics are temporarily changing the driving
characteristics. Follow the instructions on the
information display where appropriate.NOTE
The table's examples are no indication that
the car is defective but instead show that a
safety function has been activated inten-
tionally to prevent damage to one of the
car's components.
WARNING
If a warning symbol combined with the textTransm. overheat park safely is ignored
then the heat in the gearbox may become
so high that the power transmission
between engine and gearbox is temporarily
ProCarManuals.com
Page 121 of 388
03 Your driving environment
Gearboxes
03
121
halted in order to prevent the clutch from
malfunctioning - the car then loses drive and
is stationary until gearbox temperature has
cooled to an acceptable level.
For more possible display messages with their
respective proposals for solutions concerning
automatic transmission, see page 140.
A display text clears automatically after the
action has been carried out or after one press
on the indicator stalk READ button.
ProCarManuals.com
Page 123 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
* Option/accessory, for more information, see Introduction.123
Function and operation
Eco DRIVe On/Off.
Illuminates briefly on activation and for text
messages.
(Only used by the Eco Start/Stop DRIVe
function).
Driving with cruise controlThe Eco DRIVe function with activated cruise
control makes driving slightly more flexible -
the set speed is not followed exactly in the
event of an increased load, but the function
allows a barely perceptible delay, e.g. at the
beginning of a steep hill.
The reason is that Eco DRIVe implements a
slower acceleration, e.g. for compensation due
to increased load, than the normal cruise con-
trol.The cruise control's environmentally positive
flexibility is within the range of +0/-2 km/h.
Deactivating the Eco DRIVe functionThe current setting is stored when the engine
is switched off - if Eco DRIVe is e.g. activated
at engine shutdown, the function will remain
activated the next time the engine is started.
In certain situations it is
advantageous to use engine
braking, e.g. on steep down-
hill slopes, and it may then be
appropriate to temporarily
disengage the Eco DRIVe
function - this is carried out by
pressing this button (1).
The disengaged function is confirmed with a
display text and with the button's light going
out.
Text messageIn combination with this indicator
lamp the Eco DRIVe function may
display text messages on the information dis-
play for certain situations. The following table
shows some examples.
Sym-
bolMessageInfo/Action
Eco DRIVe OnIlluminates for
about 5 seconds
after Eco
DRIVe has
been activated.
Eco DRIVe OffIlluminates for
about 5 seconds
after Eco
DRIVe has
been switched
off.
If a message does not go out following com-
pletion of the action then a workshop should
be contacted - an authorised Volvo workshop
is recommended.
ProCarManuals.com
Page 124 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
124* Option/accessory, for more information, see Introduction.
Eco Start/Stop DRIVe
General information on Start/Stop
The engine is switched off - it becomes quieter and
cleaner....
Certain engines can be fitted with a
Eco Start/Stop DRIVe function which is acti-
vated during e.g. stationary traffic or waiting at
traffic lights.
The engine's automatic restart sequence runs
so smoothly that it is hardly noticeable that the
engine has actually been switched off. The
experience is that the engine has been running
the whole time but with an extremely quiet and
low idling speed.
The Eco Start/Stop DRIVe function gives the
driver the opportunity for a more active envi-
ronmentally conscious way of driving the car
by means of being able to disengage gear andletting the engine auto-stop, whenever appro-
priate.
Function and operation
Eco Start/Stop DRIVe On/Off.
Illuminates briefly on activation and for text
messages.
The engine is auto-stopped.
The Eco Start/Stop DRIVe function is
activated automatically when the
engine is started with the key. The driver is
made aware of the function by the instrument
panel symbol (2) illuminating briefly and the
green lamp (1) for the On/Off button illuminat-
ing.
NOTE
After starting with the key and each auto-
stop the car must first reach 5 km/h before
the automatic Start/Stop function is re-acti-
vated - following which certain conditions
must also be fulfilled, refer to these under
the heading "The engine does not auto-
stop".
All of the car's normal systems such as lighting,
radio, etc. work as normal even with an auto-
stopped engine, except that some equipment
may have its function temporarily reduced, e.g.
the climate control system's fan speed or
extremely high volume on the audio system.
Auto-stopping the engineIn order that the engine will auto-stop the car
must be stationary:
•Set the gear lever in neutral position and
release the clutch pedal - the engine is
switched off.
As verification and reminder
that the engine is auto-stop-
ped this symbol in the display
(3) illuminates.
Auto-starting the engineWith the gear lever in neutral position:
ProCarManuals.com
Page 125 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
* Option/accessory, for more information, see Introduction.125
•Depress the clutch pedal - the engine
starts.
or
•Depress the accelerator pedal - the engine
starts.
If the car is on a downhill slope:
•Release the foot brake and let the car roll
faster than normal walking pace - the
engine starts.
After which it is only necessary to engage a
gear and continue the journey.
Gear indicator
An essential detail in connection with environ-
mental driving is to drive in the right gear and
change gear in time.The driver is assisted by an indicator which
notifies the driver when it is most advanta-
geous to engage the next higher or lower gear
- GSI (Gear Shift Indicator).
Indication is made with an up or down arrow in
the combined instrument panel's lower dis-
play.
Deactivating the Eco Start/Stop DRIVe
function
In certain situations, it may
advisable to temporarily dis-
engage the automatic
Start/Stop function - this is
carried out with a push of this
button (1).
Disengaged Start/Stop func-
tion is indicated by the infor-
mation display's symbol (2)
going out and the message
Eco DRIVe Off being dis-
played for about 5 seconds -
while the button's lamp goes
out at the same time.
The Start/Stop function is disengaged until it is
reactivated with the button or until the next
time the engine is started with the key.
Limitations
The engine does not auto-stopEven if the Eco Start/Stop DRIVe function is
activated, the engine does not auto-stop if:
•the driver has opened the seatbelt's
buckle.
•the car has not stopped - however, the
Start/Stop function does accept slow roll-
ing, the equivalent to normal walking pace.
•the capacity of the battery is below the
minimum permissible level.
•the engine does not have normal operating
temperature.
•outside temperature is below 0 or above
30 °C.
•the environment in the passenger com-
partment differs from the preset values -
indicated by the ventilation fan running at
a high speed.
•the car has been reversed and reverse gear
is disengaged.
•battery temperature is below 0 °C or above
55 °C.
The engine auto-starts without driver
intervention
An auto-stopped engine may restart in some
cases without the driver having decided that
the journey should continue.
ProCarManuals.com
Page 126 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
126* Option/accessory, for more information, see Introduction.
In the following cases the engine auto-starts
even if the driver has not depressed the clutch
pedal in order to engage a gear:
•Misting forms on the windows.
•Outside temperature is below 0 or above
30 °C.
•There is a temporarily high current take-off
or battery capacity has dropped to the low-
est permissible level.
•The car is rolling faster than the equivalent
normal walking pace.
•Repeated pumping of the brake pedal.
WARNING
Do not open the bonnet when the engine
has auto-stopped - the engine may sud-
denly auto-start. In order to avoid auto-star-
ting with raised bonnet:
•First engage a gear and apply the park-
ing brake or take the remote control key
from the ignition switch.
The engine does not auto-startIn the following cases the engine does not
auto-start after having auto-stopped:
•The driver's seatbelt buckle has been
opened - a display text prompts the driver
to start the engine normally.
•A gear is engaged without declutching - a
display text prompts the driver to set the
gear lever in neutral position in order to
enable auto-start.
Involuntary engine stopIn the event that a start-up fails and the engine
stops, proceed as follows:
1. Depress the clutch pedal again - the engine
starts automatically after the gear lever has
been set in neutral position. Prior to this the
information display showed the text
Set
the gear lever in neutral.
Text messageIn combination with this indicator
lamp the Eco Start/Stop DRIVe func-
tion may display text messages on the infor-
mation display for certain situations. For some
of them there is a recommended action that
should be performed. The following table
shows some examples.
Sym-
bolMessageInfo/Action
Eco DRIVe OnIlluminates for
about 5 seconds
after Eco Start/
Stop DRIVe has
been activated.
Eco DRIVe OffIlluminates for
about 5 seconds
after Eco Start/
Stop DRIVe has
been switched
off.
Disengage to
startThe engine is
ready to auto-
start - waiting
for the clutch
pedal to be
depressed.
Depress the
foot brake to
startThe engine is
ready to auto-
start - waiting
for the brake
pedal to be
depressed.
ProCarManuals.com
Page 132 of 388
03 Your driving environment
Parking brake
03
132
Disengaging the parking brake
Parking brake control.
Cars with manual gearbox
Releasing manually
1. Insert the remote control key in the ignition
switch.
2. Depress the brake pedal firmly.
3. Pull the control.
NOTE
The parking brake can also be released
manually by depressing the clutch pedal
instead of the brake pedal. Volvo recom-
mends the use of the brake pedal.
Releasing automatically1. Start the engine.2. Ease up the clutch and depress the accel-
erator.
Cars with automatic gearbox
Releasing manually
1. Insert the remote control key in the ignition
switch.
2. Depress the brake pedal firmly.
3. Pull the control.
Releasing automatically1. Put the seatbelt on.
2. Start the engine.
3.
Move the gear selector to position D or R
and depress the accelerator.
NOTE
For safety reasons, the parking brake is only
released automatically if the engine is run-
ning and the driver is wearing a seatbelt. The
parking brake is released immediately on
cars with automatic gearbox when the
accelerator pedal is depressed and the gear
selector is in position D or R.
Heavy load uphillA heavy load, such as a trailer, can cause the
car to roll backward when the parking brake is
released automatically on a steep incline.
Avoid this by depressing the control while driv-ing off. Release the control when the engine
achieves traction.
Cars with Keyless drive functionRelease manually by pressing the
START/STOP ENGINE button, then depress
the brake or clutch pedal and pull the control.
Symbols
SymbolSpecification
Read the message on the infor-
mation display
A flashing symbol indicates that
the parking brake is applied. If
the symbol flashes in any other
situation then this means that a
fault has arisen. Read the mes-
sage on the information display.
ProCarManuals.com
Page 140 of 388
04 Comfort and driving pleasure
Menus and messages
04
140* Option/accessory, for more information, see Introduction.
Combined instrument panel
Information display and controls for menus.
READ – access to message list and mes-
sage confirmation.
Thumbwheel – browse between menu
options.
RESET – reset the active function. Used in
certain cases to select/activate a function,
see the explanation under each respective
function.
The menus shown on the information displays
in the combined instrument panel are con-
trolled with the left-hand stalk switch. The
menus shown depend on key position, see
page 81. If a message appears then this must
be acknowledged with READ for the menus to
be shown.
Menu overviewSome of the following menu options require the
function and hardware to be installed in the car.
To empty fuel tank
Average
Instantaneous
Average speed
Current speed
1
Engine oil level*
Tyre pressure Calibration*
Park heat timer 1/2*
Park vent timer 1/2*
Park timer mode*
Direct start Park heat*
Direct start Park el.heat*
Direct start Park vent*
Additional heat auto*
Rest heat start*
Lane departure warning*
Driver Alert*
Message
Text message in the information display.
When a warning, information or indicator sym-
bol illuminates, a corresponding message
appears on the information display. An error
message is stored in a memory list until the
fault is rectified.
Press READ to acknowledge and browse
between the messages.
NOTE
If a warning message appears while you are
using the trip computer, the message must
be read (press READ) before the previous
activity can be resumed.
ProCarManuals.com
Page 142 of 388
04 Comfort and driving pleasure
Menu source MY CAR
04
142* Option/accessory, for more information, see Introduction.
General information about MY CAR
Many of the car's features are handled
in this menu source, such as setting the
clock, door mirrors and locks.
Navigation in the menus is carried out using
some of the centre console buttons or with the
steering wheel's right-hand keypad.
Certain functions are standard, others are
optional - the range also varies depending on
the market.
Operation
Centre console controls
Centre console controls for menu navigation.
Press MY CAR to open the menus underMY CAR.
Press OK MENU to select/tick in the high-
lighted menu option or to store the
selected function in the memory.
Turn TUNE to scroll up/down among the
menu options.
EXIT
•Short presses on EXIT go back one step in
the current menu structure.
•One long press on EXIT leads to the MY
CAR source menu.
•A long press on EXIT while in the MY
CAR source menu, leads out of MY CARto the menu system's main menu - Parent
view, from where all the car's functions/
menu sources can be accessed, see
page 220.
Steering wheel keypad*
The keypad may vary depending on market.
Turn the thumbwheel to scroll up/down
among the menu options.
Press the thumbwheel to select/tick in the
highlighted menu option or to store the
selected function in the memory.
EXIT
Search pathsCurrent menu level is shown at the top right of
the centre console display screen. Search
paths to the menu system functions are descri-
bed in this manual in the following form:
ProCarManuals.com