light VOLVO V60 2011 Owner's Guide
[x] Cancel search | Manufacturer: VOLVO, Model Year: 2011, Model line: V60, Model: VOLVO V60 2011Pages: 388, PDF Size: 9.32 MB
Page 105 of 388
03 Your driving environment
Windows, rearview and door mirrors
03
* Option/accessory, for more information, see Introduction.105
Automatic dimming*Bright light from behind is automatically
dimmed by the rearview mirror. The control is
not available in mirrors with automatic dim-
ming.
The compass* can only be specified for rear-
view mirrors with automatic dimming, see
page 106.
ProCarManuals.com
Page 115 of 388
03 Your driving environment
Starting the engine – external battery
03
115 Jump starting
If the battery is flat then the car can be started
with current from another battery.
The following points are recommended when
using a donor battery in order to avoid the risk
of an explosion:
1. Insert the remote control key in key posi-
tion 0, see page 81.
2. Ensure that the donor battery is 12 volt.
3. If the donor battery is in another car, switch
off the donor car's engine in the other car
and ensure that the cars do not touch one
another.
4. Connect the red jump lead to the positive
terminal on the donor battery
.5. Open the clips on the front cover of the
battery in your car and remove the cover,
see page 322.
6. Connect the red jump lead to the battery's
positive terminal
.
7. Connect one end of the black jump lead to
the donor battery's negative terminal
.
IMPORTANT
Connect the start cable carefully to avoid
short circuits with other components in the
engine compartment.
8. Connect the other clamp to an earthing
point, (right-hand engine mounting at the
top, the outer screw head)
. Check that
the jump lead clamps are fixed securely so
that there are no sparks during the starting
procedure.
9. Start the engine of the "donor car". Let the
engine run a few minutes at a speed slightly
higher than idle (1500 rpm).
10. Start the engine of the car with the flat bat-
tery. Do not touch the crocodile clips dur-
ing the start procedure. There is a risk of
sparks forming.11. Remove the jump leads, first the black and
then the red.
Make sure that none of the clamps on the
black jump lead comes into contact with
the battery's positive terminal or the clamp
connected to the red jump lead.
WARNING
The battery can generate oxyhydrogen gas,
which is highly explosive. One spark, which
can be generated if you connect a jump lead
incorrectly, is sufficient to make the battery
explode. The battery contains sulphuric
acid, which can cause serious burns. If the
acid comes into contact with eyes, skin or
clothing, flush with large quantities of water.
If acid splashes into the eyes, seek medical
attention immediately.
ProCarManuals.com
Page 122 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
122* Option/accessory, for more information, see Introduction.
General
Quieter and cleaner
Environmental care is one of Volvo Car Corpo-
ration's core values and it influences all of our
operations. This target-orientation has resulted
in the DRIVe vehicle series whose concept
consists of an interaction between several sep-
arate energy-saving functions, all with the
common purpose of reducing fuel consump-
tion, which in turn contributes to reduced
exhaust emissions.
Both variants Eco DRIVe and
Eco Start/Stop DRIVe contain various energy-
saving functions depending on which gearbox
the car is equipped with:A V60 with this button on the
instrument panel and....
•....automatic transmission has the
Eco DRIVe function
•....manual gearbox has the
Eco Start/Stop DRIVe function.
Note that the car can only be equipped with
one of the functions - either Eco DRIVe or
Eco Start/Stop DRIVe - not both.
More information and settings
The MY CAR menu system in the car includes
an integrated owner's manual which explains
the DRIVe concept in detail along with its pos-
sible settings and options - see page 143.
Eco DRIVe
General information on EcoUse of the Eco DRIVe function activates a pro-
gram that helps the driver to drive the car eco-
nomically with minimum fuel consumption and
emissions.
In practice this means that engine braking is
reduced, meaning that the car's kinetic energy
can be used for rolling long distances with the
engine speed at idling speed.
Another environmentally positive Eco DRIVe
effect is that the program interprets accelera-
tion slightly more slowly than the driver does -
this in order to achieve maximum fuel savings
during acceleration.
ProCarManuals.com
Page 123 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
* Option/accessory, for more information, see Introduction.123
Function and operation
Eco DRIVe On/Off.
Illuminates briefly on activation and for text
messages.
(Only used by the Eco Start/Stop DRIVe
function).
Driving with cruise controlThe Eco DRIVe function with activated cruise
control makes driving slightly more flexible -
the set speed is not followed exactly in the
event of an increased load, but the function
allows a barely perceptible delay, e.g. at the
beginning of a steep hill.
The reason is that Eco DRIVe implements a
slower acceleration, e.g. for compensation due
to increased load, than the normal cruise con-
trol.The cruise control's environmentally positive
flexibility is within the range of +0/-2 km/h.
Deactivating the Eco DRIVe functionThe current setting is stored when the engine
is switched off - if Eco DRIVe is e.g. activated
at engine shutdown, the function will remain
activated the next time the engine is started.
In certain situations it is
advantageous to use engine
braking, e.g. on steep down-
hill slopes, and it may then be
appropriate to temporarily
disengage the Eco DRIVe
function - this is carried out by
pressing this button (1).
The disengaged function is confirmed with a
display text and with the button's light going
out.
Text messageIn combination with this indicator
lamp the Eco DRIVe function may
display text messages on the information dis-
play for certain situations. The following table
shows some examples.
Sym-
bolMessageInfo/Action
Eco DRIVe OnIlluminates for
about 5 seconds
after Eco
DRIVe has
been activated.
Eco DRIVe OffIlluminates for
about 5 seconds
after Eco
DRIVe has
been switched
off.
If a message does not go out following com-
pletion of the action then a workshop should
be contacted - an authorised Volvo workshop
is recommended.
ProCarManuals.com
Page 124 of 388
03 Your driving environment
Eco DRIVe or Eco Start/Stop DRIVe*
03
124* Option/accessory, for more information, see Introduction.
Eco Start/Stop DRIVe
General information on Start/Stop
The engine is switched off - it becomes quieter and
cleaner....
Certain engines can be fitted with a
Eco Start/Stop DRIVe function which is acti-
vated during e.g. stationary traffic or waiting at
traffic lights.
The engine's automatic restart sequence runs
so smoothly that it is hardly noticeable that the
engine has actually been switched off. The
experience is that the engine has been running
the whole time but with an extremely quiet and
low idling speed.
The Eco Start/Stop DRIVe function gives the
driver the opportunity for a more active envi-
ronmentally conscious way of driving the car
by means of being able to disengage gear andletting the engine auto-stop, whenever appro-
priate.
Function and operation
Eco Start/Stop DRIVe On/Off.
Illuminates briefly on activation and for text
messages.
The engine is auto-stopped.
The Eco Start/Stop DRIVe function is
activated automatically when the
engine is started with the key. The driver is
made aware of the function by the instrument
panel symbol (2) illuminating briefly and the
green lamp (1) for the On/Off button illuminat-
ing.
NOTE
After starting with the key and each auto-
stop the car must first reach 5 km/h before
the automatic Start/Stop function is re-acti-
vated - following which certain conditions
must also be fulfilled, refer to these under
the heading "The engine does not auto-
stop".
All of the car's normal systems such as lighting,
radio, etc. work as normal even with an auto-
stopped engine, except that some equipment
may have its function temporarily reduced, e.g.
the climate control system's fan speed or
extremely high volume on the audio system.
Auto-stopping the engineIn order that the engine will auto-stop the car
must be stationary:
•Set the gear lever in neutral position and
release the clutch pedal - the engine is
switched off.
As verification and reminder
that the engine is auto-stop-
ped this symbol in the display
(3) illuminates.
Auto-starting the engineWith the gear lever in neutral position:
ProCarManuals.com
Page 129 of 388
03 Your driving environment
Foot brake
03
129 General
The car is equipped with two brake circuits. If
one brake circuit is damaged then this will
mean that the brakes engage at a deeper level
and harder pressure on the pedal is needed to
produce the normal braking effect.
The driver's brake pedal pressure is assisted
by a brake servo.
WARNING
The brake servo only works when the engine
is running.
If the brake is used when the engine is switched
off then the pedal will feel stiff and more force
must be used to brake the car.
In very hilly terrain or when driving with a heavy
load the brakes can be relieved by using engine
braking. Engine braking is most efficiently used
if the same gear is used downhill as up.
For more general information on heavy loads
on the car, see page 350.
Anti-lock braking systemThe car is equipped with ABS (Anti-lock
Braking System) which prevents the wheels
from locking during braking. This means the
ability to steer is maintained and it is easier to
swerve to avoid a hazard for example. Vibrationmay be felt in the brake pedal when this is
engaged and this is normal.
A short test of the ABS system is made auto-
matically after the engine has been started
when the driver releases the brake pedal. A
further automatic test of the ABS system may
be made when the car reaches 10 km/h. The
test may be experienced as pulses in the brake
pedal.
Emergency brake lights and automatic
hazard warning flashers
Emergency brake lights are activated to alert
vehicles behind about sudden braking. The
function means that the brake light flashes
instead of - as in normal braking - shining with
a constant glow.
Emergency brake lights are activated at
speeds above 50 km/h if the ABS system is
working and/or in the event of sudden braking.
After the car's speed has been slowed below
10 km/h the brake light returns from flashing to
the normal constant glow - while at the same
time the hazard warning flashers are activated,
and they flash until the driver changes engine
speed with the accelerator pedal or they are
deactivated with their button, see page 92.
Cleaning the brake discsCoatings of dirt and water on the brake discs
may result in delayed brake function. This delay
is minimised by cleaning the brake linings.
Manual cleaning is advisable with wet road sur-
faces, prior to long-stay parking and after the
car has been washed. Carry this out by braking
gently during a short period while en route.
Emergency Brake AssistanceEmergency Brake Assistance EBA (Emergency
Brake Assist) helps to increase brake force and
so reduce braking distance. EBA detects the
driver's braking style and increases brake force
as necessary. The brake force can be rein-
forced up to the level when the ABS system is
engaged. The EBA function is interrupted when
the pressure on the brake pedal is reduced.
NOTE
When EBA is activated the brake pedal low-
ers slightly more than usual, depress (hold)
the brake pedal as long as necessary. If the
brake pedal is released then all braking
ceases.
ProCarManuals.com
Page 134 of 388
03 Your driving environment
HomeLink Ÿ Ÿ *
03
134* Option/accessory, for more information, see Introduction.
General
HomeLink Ÿ is a programmable remote control
which can control up to three different devices
(e.g. garage door, alarm system, outdoor light-
ing and indoor lighting etc.) and in doing so
replace their remote controls. HomeLink
Ÿ is
supplied built into the left-hand sun visor.
The HomeLink
Ÿ panel consists of three pro-
grammable buttons and one indicator lamp.
NOTE
HomeLink Ÿ is designed not to work if the car
is locked from the outside.
Save the original remote controls for future
programming (e.g. when switching to
another car).
Delete the button programming when the
car is to be sold.
Metallic sun visors should not be used in
cars fitted with HomeLink
Ÿ. This may have
an adverse effect on its function.
Operation
When HomeLink Ÿ is fully programmed it can be
used in place of the separate original remote
controls.
Depress the programmed button to activate
the garage door, alarm system etc. The indi-
cator lamp illuminates for the time that the but-
ton is kept depressed.
NOTE
If the ignition is not activated, HomeLink Ÿ
will work for 30 minutes after the driver's
door has been opened.
The original remote controls can of course be
used in parallel with HomeLink Ÿ.
WARNING
If HomeLink Ÿ is used to operate a garage
door or gate, ensure that nobody is in the
vicinity of the door or gate while it is in
motion.
Do not use the HomeLink
Ÿ remote control
for any garage door that does not have
safety stop and safety reverse. The garage
door must react immediately when it
detects that something is preventing its
movement, and stop directly and reverse. A
garage door without these characteristics
could cause personal injury. For further
information - contact the supplier via the
Internet: www.homelink.com.
Programming for the first timeThe first step erases the memory in
HomeLink Ÿ and must not be carried out when
only one individual button is being reprogram-
med.
1. Depress the two outer buttons and do not
release until the indicator lamp starts to
flash after approx. 20 seconds. The flash-
ing indicates that HomeLink
Ÿ is set in
"learn mode" and is ready to be pro-
grammed.
2. Position the original remote control
5-30 cm from HomeLink
Ÿ. Monitor the indi-
cator lamp.
ProCarManuals.com
Page 142 of 388
04 Comfort and driving pleasure
Menu source MY CAR
04
142* Option/accessory, for more information, see Introduction.
General information about MY CAR
Many of the car's features are handled
in this menu source, such as setting the
clock, door mirrors and locks.
Navigation in the menus is carried out using
some of the centre console buttons or with the
steering wheel's right-hand keypad.
Certain functions are standard, others are
optional - the range also varies depending on
the market.
Operation
Centre console controls
Centre console controls for menu navigation.
Press MY CAR to open the menus underMY CAR.
Press OK MENU to select/tick in the high-
lighted menu option or to store the
selected function in the memory.
Turn TUNE to scroll up/down among the
menu options.
EXIT
•Short presses on EXIT go back one step in
the current menu structure.
•One long press on EXIT leads to the MY
CAR source menu.
•A long press on EXIT while in the MY
CAR source menu, leads out of MY CARto the menu system's main menu - Parent
view, from where all the car's functions/
menu sources can be accessed, see
page 220.
Steering wheel keypad*
The keypad may vary depending on market.
Turn the thumbwheel to scroll up/down
among the menu options.
Press the thumbwheel to select/tick in the
highlighted menu option or to store the
selected function in the memory.
EXIT
Search pathsCurrent menu level is shown at the top right of
the centre console display screen. Search
paths to the menu system functions are descri-
bed in this manual in the following form:
ProCarManuals.com
Page 144 of 388
04 Comfort and driving pleasure
Menu source MY CAR
04
144
Driver door, then all
Keyless entry
All doors
Any door
Doors on same side
Both front doors
For more information, see page 50 and 59 and
62.
Reduced Guard
Activate once
Ask when exiting
For more information, see page 64 and 68.
Side mirror settings
Fold mirrors
Tilt left mirror
Tilt right mirror
For more information, see page 103.
Light settings
Door lock confirmation light
Door unlock confirmation light
For more information, see page 48.Approach light duration
Off
30 sec
60 sec
90 sec
For more information, see page 50 and 94.
Home safe light duration
30 sec
60 sec
90 sec
For more information, see page 94.
Door lock confirmation light
For more information, see page 48.
Daytime running lights
For more information, see page 89.
Temporary LH traffic
Temporary RH traffic
For more information, see page 94.
Active bending lights
For more information, see page 90.Tyre pressure system
Warns if tyre pressure is too low
Calibrate tyre pressure
For more information, see page 299.
Steering wheel force
High
Medium
Low
For more information, see page 166.
Reset car settings
This option resets the menu system to the orig-
inal factory settings in Car settings.
MY CARSettingsDriver support
systems
Collision warning
Collision Warning
Warning distance
Long
Normal
Short
Warning sound
ProCarManuals.com
Page 155 of 388
04 Comfort and driving pleasure
Climate control
04
* Option/accessory, for more information, see Introduction.155
NOTE
Heating or cooling cannot be hastened by
selecting a higher/lower temperature than
the actual temperature required.
AC – Air conditioning on/offWhen the lamp in the AC but-
ton illuminates, the air condi-
tioning is controlled by the
system's automatic function.
This way, incoming air is
cooled and dehumidified.
When the lamp in the AC button is switched off
the air conditioning is disconnected. Other
functions are still controlled automatically.
When the max. defroster function is activated
the air conditioning is switched on automati-
cally, so that the air is dehumidified at the maxi-
mum setting.
Max. defrosterUsed to quickly remove mist-
ing and ice from the wind-
screen and side windows. Air
flowing to the windows. The
light in the defroster button
illuminates when the function
is active.
The following also takes place in order to pro-
vide maximum dehumidification in the passen-
ger compartment:
•the air conditioning is automatically
engaged
•recirculation and the air quality system are
automatically disengaged.
NOTE
The noise level increases as the fan is oper-
ating at max.
When the defroster is switched off the climate
control returns to the previous settings.
Recirculation
Recirculation
When recirculation is
engaged the orange lamp in
the button illuminates. The
function is selected to shut
out bad air, exhaust gases
etc. from the passenger com-
partment. The air in the pas-
senger compartment is recirculated, i.e. no
outside air is taken into the car when this func-
tion is activated.
IMPORTANT
If the air in the car recirculates for too long,
there is a risk of misting on the insides of the
windows.
TimerWith the timer function activated the system
will exit manually activated recirculation mode
according to a time that depends on the out-
side temperature. This reduces the risk of ice,
misting and bad air. Activate/deactivate the
function in the menu system MY CAR under
Settings
Climate settings
Recirculation timer. For a description of the
menu system, see page 142.
NOTE
When max. defroster is selected, recircula-
tion is always deactivated.
Air quality system IAQS*The air quality system separates gases and
particles to reduce the levels of odours and
pollution in the passenger compartment. If the
outside air is contaminated then the air intake
is closed and the air is recirculated.
Activate/deactivate the function in the menu
system MY CAR under Settings
Climate
ProCarManuals.com