ignition VOLVO V70 2000 Owner's Manual

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_06.htm[4/4/2013 10:24:41 PM]
3. Tail light
4. Back-up light
5. Tail light / Rear fog light (left side only)
All the bulbs in the tail light unit are replaced from inside the cargo space as follows:
· Turn the ignition key to position 0 and switch off the lights.
· Remove the upper panel of the tail light unit by using a screwdriver (1) and/or the lower panel by first removing the
side floor cover and turning the plastic screw at the bottom of the panel to release it.
· Press down catch A (upper section) * or press catches B toward each other (lower section) and take out the bulb
holder.
· Leave the connector and cables connected to the bulb holder.
· Remove the bulb by pressing it inwards and turning it slightly counter-clocKWise.
· Insert a new bulb into the bulb holder and reinstall the holder in the tail light assembly.
· Check that the bulb works. Reinstall the cover.
* The optional speaker (see illustrations 2, 3)) must be removed first to gain access to the upper bulb holder.
pg. 101 Replacing bulbs
Insert screwdriver and turn
Trunk light (sedans)/Rear courtesy light (wagons)
· Switch off the lights.
· Press in the catch with a screwdriver and remove the bulb holder.
· Replace the bulb and reinstall the bulb holder.
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_06.htm[4/4/2013 10:24:41 PM]
Torx screwdriver for glass lens
License plate lights (sedans and wagons)
· Switch off the lights.
· Unscrew the screw*.
· Insert the screwdriver and turn gently to loosen the glass lens.
· Replace the bulb and reinstall the glass lens.
* Two screws on wagons
pg. 102 Replacing bulbs
Insert screwdriver, turn and pull downward
Front courtesy lights
· Switch off the ignition.
· Insert a screwdriver and turn carefully to loosen the glass lens.
· Replace the bulb and press the glass lens back into place.
Insert a screwdriver and turn
Rear reading lights
· Switch off the ignition.
· Insert a screwdriver and turn to loosen the lamp unit.
· Replace the bulb and press the lamp unit back into place.
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_06.htm[4/4/2013 10:24:41 PM]
Insert a screwdriver and turn
Vanity mirror
· Switch off the ignition.
· Insert a screwdriver under the lower edge and turn to loosen the glass lens.
· Push out the bulb and replace it.
· Press the lower edge of the lens into place above the four catches.
· Press the upper edge of the lens into place.
pg. 103 Replacing bulbs
Insert the screwdriver and turn gently (rear door)
Door warning lights
· Slide the lamp unit upward and pull out the lower edge.
· Twist off the bulb holder.
· Pull the bulb straight out.
· Replace the bulb.
· Reinstall the holder and lamp unit in reverse order.
Insert a screwdriver
Door step courtesy lights
· Insert a screwdriver and pry out the glass lens.
· Withdraw the lamp unit, bend back the tabs and remove the plate.
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_06.htm[4/4/2013 10:24:41 PM]
* Fuses in the Relay/Main fuse box should only be changed by an authorized Volvo service technician.
pg. 105 Fuses
Relay/Main fuse box
Fuses in the main fuse box protect the entire electrical system. If one of the fuses blows, there is a serious electrical
fault. Do not change any of these fuses. Contact your nearest Volvo workshop for a closer analysis.
Relays
15 System relay
16 Air pump relay
17 Starter motor
18 Air conditioning
Fuses in Relay/Main fuse box (main system fuses)
Location * Amperage
1 Electric cooling fan 60A
2 Fuses in Supplementary fuse box 50A
3 Starter motor, air pump 50A
4 ABS, STC, TRACS 50A
5 Headlights 50A
6 Fuses in Supplementary fuse box 60A
7 Fuses in Supplementary fuse box 60A
8 Control modules - engine/automatic transmission 60A
9 Electrically operated windows 60A
10 Ignition switch, Control modules - engine/automatic transmission 10A
11 Fuel injectors, A/C relay 10A
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_06.htm[4/4/2013 10:24:41 PM]
12 Fuel pump, fuel injection system20A
13 Control module - automatic transmission10A
14 A/C relay, emissions systems 10A
* Some of the equipment/systems listed may be available on certain models only.
pg. 106 Fuses (supplementary fuse box)
Location * Amperage
1 -
2 Central locking, driving mode selectors (aut. trans.) 10A
3 ABS 10A
4 Immobilizer (Canada only) 10A
5 Climate systems, Onboard diagnostics OBDII 15A
6 -
7 Audio system 15A
8 Immobilizer (Canada only), trip computer, headlight switch 15A
9 Electrically heated rear seat (certain models) 20A
10 Ignition switch 15A
11 Brake lights 10A
12 -
13 Hazard warning flashers, headlight flashers, remote
operated central locking system 15A
14 Heated rear window and door mirrors 30A
15 Courtesy lights, door open warning lights, trunk/cargo
space light, seat belt reminder, glove compartment light 10A
16 Power antenna, electrical connector for trailer, accessories 30A
17 Front fog lights 20A
18 Key reminder 10A
19 Left high beam 15A
20 Right high beam, high beam indicator light 15A
21 Left low beam 15A
22 Right low beam 15A
23 Left front/rear parking lights, left tail light, license plate lights 10A
24 Right front/rear parking lights, right tail light 10A
25 Rear fog light, rear fog light indicator lamp 10A
26 Headlight switch 15A
27 Backup lights, turn signals 15A
28 Heated seats - front/rear (certain models) 25A
29 Heated rear window, shiftlock, seat belt reminder, cruise
control, heated door mirrors, bulb failure warning sensor 10A
30 -
31 Passenger compartment blower-climate systems 25A
32 Audio system 10A
33 Tailgate wiper/washer 15A
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_06.htm[4/4/2013 10:24:41 PM]
the blade with water.
Wiper blades should be checked on a regular basis and replaced when worn.
pg. 110 In case of emergency
Shiftlock release (automatic transmission only)
The gear selector is locked in the (P)ark position. To manually release the shiftlock:
· Turn the starting (ignition) key to position I
· Press firmly on the "SHIFTLOCK OVERRIDE" button located to the right of the base of the gear selector
· While holding the override button down, press the button on the front of the gear selector
· Move the selector from the (P)ark position.
Electrically operated windows
The electrically operated window motors have an overload protecting circuit breaker (fuse no. 37) which is activated
when an object blocks a window. Should this occur, remove the object and wait 20 seconds for the circuit breaker to
reset.
The electrically operated windows should then function.
Sun roof
The electrically operated sun roof has an overload protecting circuit breaker (fuse no. 37) which is activated when an
object blocks the sun roof. Should this occur, remove the object and wait 20 seconds for the circuit breaker to reset.
The sun roof should then function normally. Also check fuse no. 35.
Electrically operated front seats
The electrically operated front seats have overload protecting circuit breakers (fuses no. 39 and 40) which are activated
when an object blocks one of the seats. Should this occur, remove the object and wait 20 seconds for the circuit
breaker to reset. The seat should then function normally.

Contents | Top of Page
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_09.htm[4/4/2013 10:25:03 PM]
2 0 0 0
VOLVO
S & V70
Chapter 9 - Specifications
pg. 133 Service an investment
This chapter contains facts and figures pertaining to the technical specifications of your car. Oil/fluids specifications 134
Engine specifications135
Cooling/fuel/distributor ignition systems136
Front/rear suspensions136
Transmission, Capacities, Vehicle loading137
Electrical system/bulbs138
Weights139
Dimensions, Service manuals, Road assistance140
pg. 134 Oil/fluid specifications
Oil quality
Meeting API specification SJ, SJ/CF, or SJ/Energy Conserving.
For best fuel economy and engine protection, consult your authorized Volvo retailer for recommended oils. Oil with a
different quality rating may not provide adequate engine protection.
Synthetic oils complying with oil quality requirements are recommended for: driving in areas of sustained temperature
extremes (hot or cold), when towing a trailer over long distances or for prolonged driving in mountainous areas.
Extra oil additives must not be used unless advised by an authorized Volvo retailer.
Viscosity (stable ambient temperatures):
Engine oilQuality:
Meeting API specification SJ, SJ/CF,
or SJ/Engergy Conserving Capacity (incl. filter)
: 6.1 US
qts (5.8 liters).*
Automatic transmission fluid Quality:
AW4: ATF Dexron III and Mercon.
AW5: Only Volvo gearbox oil (1161540-8). Do Capacity:
8 US qts. (7.6
liters)
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_09.htm[4/4/2013 10:25:03 PM]
Displacement2.3 liters
Compression ratio8.5:1
Number of valves 20
Designation: Volvo B 5244 T2
Output 261 hp at 5700 rpm (195 KW/95 rps)
Max. torque 258 ft. lbs. at 2400-5100 rpm (350 Nm/4085 rps)
Number of cylinders 5
Bore 3.19" (81 mm)
Stroke 3.54" (90 mm)
Displacement 2.3 liters
Compression ratio 8.5:1
Number of valves 20
All specifications are subject to change without notice.
pg. 136 Specifications
Cooling system
Type: Positive pressure, closed system
Thermostat begins to open at 186° F (90° C)
Turbo -charged models 180° F (87° C)
Coolant: Volvo original coolant/antifreeze
Capacity: 7.6 US qts. (7.2 liters)
Turbo -charged models 7.4 US qts. (7.0 liters)
Fuel system
The engine is equipped with a multiport fuel injection system.
Distributor ignition system
Firing order: 12453
Distributor ignition setting: Not adjustable
Spark plugs: Bosch FR7DC or Champion RC9YC
Spark plug gap: 0.028" (0.7 mm)
Turbo -charged models: Champion RC8PYP (or equivalent)
Spark plug gap: 0.03" (0.75 mm)
Tightening torque: 18.4 ft. lbs. +/ 3.7 ft. lbs. (25 Nm +/ 5 Nm)
WARNING!
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_09.htm[4/4/2013 10:25:03 PM]
The distributor ignition system operates at very high voltages. Special safety precautions must be followed to
prevent injury. Always turn the ignition off when:
· Replacing distributor ignition components e.g. plugs, coil, etc.
· Do not touch any part of the distributor ignition system while the engine is running. This may result in unintended
movements and body injury.
Replacing spark plugs
The spark plugs should be changed every 30,000 miles (48,000 km). However, city driving or fast highway driving
may necessitate changing after 15,000 miles (24,000 km) of driving. When installing new plugs, be sure to fit the right
type and use correct torque, see "Specifications". When changing the plugs, check that the suppressor connectors are in
good condition. Cracked or damaged connectors should be replaced. When changing the spark plugs, clean the
terminals and the rubber seals.
Front suspension
Spring strut suspension with integrated shock absorbers and control arms linked to the support frame. Powerassisted
rack and pinion steering. Safety type steering column.
The alignment specifications apply to an unladen car but include fuel, coolant and spare wheel.
Toe-in measured on the wheel rims: 2.4 mm +/ 0.7 mm
Toe-in measured on tire sides: 2.9 +/ 0.9 mm
Rear suspension
Deltalink individual rear wheel suspension with longitudinal support arms, double link arms and track rods.
Toein measured on the tire sides: 4° +/ 10°
All specifications are subject to change without notice.
pg. 137 Specifications
Power transmission
Manual transmission: M 56 H
Singledisc dry plate clutch. Allsynchromesh on all gears including reverse; integrated final drive. Operation via a floor
mounted gear lever.
Final drive ratio 4.00:1
Reduction ratios
1st gear 3.07:1
2nd gear 1.77:1
3rd gear 1.19:1
4th gear 0.87:1
5th gear 0.70:1
ProCarManuals.com

2000 Volvo S & V70
http://new.volvocars.com/ownersdocs/2000/2000_SV70/00sv70_10a.htm[4/4/2013 10:25:18 PM]
Refer to the radio code card supplied with your vehicle or ask your Volvo retailer for the correct code.
When the car is parked with the ignition key removed, the anti-theft LED will flash.
Anti-theft LED
To enter the code
After installation or when the set has been disconnected from power, the set displays "COdE" when it is switched on.
Enter the 4-digit code using the preset buttons.
If the correct code is entered, "on" is displayed and the set is ready to use.
If you enter an incorrect code you must enter the correct code again from the beginning.
Incorrect code
If an incorrect code has been entered "rPt" is displayed. Enter the correct code.
After three unsuccessful coding attempts the set will lock and remain locked for two hours. "OFF" is displayed.
During this waiting period:
· the battery must be connected
· the ignition key must be turned to position I
· the unit must be turned on
Make sure the headlights are turned off to help prevent battery drain (please refer to page 26
for information on turning
the headlights off).
Enter the code again once this time has elapsed.
pg. 144 Radio SC -813
ProCarManuals.com