wheel bolts VOLVO XC70 2003 Owners Manual

2003 VOLVO XC70
WARNING!
The temperature grade for this tire is established for a tire that is pr\
operly inflated and not overloaded.
Excessive speed, under-inflation, or excessive loading, either separatel\
y or in combination, can cause
heat buildup and possible tire failure.


pg. 112 Changing wheels


Insert flat end of lug wrench and turn/pull straight out
Changing wheels
The spare wheel is located under the carpet on the cargo area floor. The\
jack and crank are secured in the
wheel recess. There are two jack attachment points on each side of the c\
ar.
To change a wheel:
l Engage the parking brake.
l Put the gear selector in (P)ark.
l Remove the wheel cap (where applicable) using the lug wrench in the to\
ol kit.
l With the car still on the ground, use the lug wrench to loosen the wheel\
bolts 1/2 - 1 turn by exerting
downward pressure. Turn the bolts counterclockwise to loosen.
file:///K|/ownersdocs/2003/2003_XC70/03xc70_07.htm (7 of 10)12/30/2006\
4:18:01 PM

2003 VOLVO XC70

Loosen wheel bolts
l Position the jack on the bar in the attachment (A in the illustration i\
n right column) and crank while
simultaneously guiding the base of the jack to the ground. The base of the jack must be flat on a level,
firm, non-slippery surface. Before raising the car, check that the jack \
is still correctly positioned in
the attachment.
l Raise the vehicle until the wheel to be changed is lifted off the ground\
.
l Unscrew the wheel bolts completely and carefully remove the wheel so as \
not to damage the thread
on the studs.
NOTE: See also
page 133 for hoisting the vehicle on a garage lift!
WARNING!
l The jack must correctly engage the bar in the jack attachment (A). The\
car's weight must not rest
on the jack attachment (B). See illustration on
page 113.
l Be sure the jack is on a firm, level, non-slippery surface.
l Never allow any part of your body to be extended under a car supported b\
y a jack.
l Use the jack intended for the car when replacing a wheel. For any other \
job, use stands to support
the side of the car being worked on.
l Apply the parking brake and put the gear selector in the (P)ark positi\
on.
l Block the wheels standing on the ground, use rigid wooden blocks.


pg. 113 Wheels and tires

file:///K|/ownersdocs/2003/2003_XC70/03xc70_07.htm (8 of 10)12/30/2006\
4:18:01 PM

2003 VOLVO XC70

Attaching the jack
NOTE: To avoid excessive wear and the necessity of rebalancing, mark and reins\
tall wheels in the same
location and position as before removal. To lessen the chance of imbalan\
ce, each wheel hub is equipped
with a guide stud to ensure that a removed wheel can be reinstalled in i\
ts original position (as when
changing over to winter tires/wheels).
NOTE: Refer to
page 133 for hoisting the vehicle on a garage lift.

Jack for AWD models
CAUTION:
l The car must not be driven with wheels of different dimensions or with a\
spare tire other than the one
that came with the car. The use of different size wheels can seriously d\
amage your car's transmission.
l Correct tightening torque on wheel bolts must be observed. The wheel bol\
ts should never be greased
or lubricated. The extended, chromed wheel bolts must not be used with s\
teel rims, as they make it
impossible to fit the hub caps.
file:///K|/ownersdocs/2003/2003_XC70/03xc70_07.htm (9 of 10)12/30/2006\
4:18:01 PM

2003 VOLVO XC70

Correct tightening order for wheel bolts
Installing the wheel
l Clean the contact surfaces on the wheel and hub.
l Lift the wheel and place it on the hub. Make sure that you align the whe\
el with the guide stud on the
wheel hub prior to installation.
l Install the wheel bolts and tighten hand-tight. Using the lug wrench, ti\
ghten crosswise (see illustration
above) until all bolts are snug.
l Lower the vehicle to the ground and alternately tighten the bolts crossw\
ise to 100 ft. lbs. (136 Nm).
l Install the wheel cap (where applicable).




Contents | Top of Page
file:///K|/ownersdocs/2003/2003_XC70/03xc70_07.htm (10 of 10)12/30/200\
6 4:18:01 PM