turn signal VOLVO XC70 2009 Owner´s Manual

04 Comfort and driving pleasure
Collision warning with Auto-brake (option)
04``161
support is activated. Brake support prepares
the brake system to react quickly, and the
brakes are applied slightly. This may be expe-
rienced as a light tug.
If the brakes are applied quickly, full braking
effect will be provided, even if pressure on the
brake pedal is light.Auto-brakeIf a collision is imminent and the driver has not
applied the brakes, the auto-brake function is
activated without the driver pressing the brake
pedal. Limited brake force is applied to reduce
the vehicle’s speed when the collision occurs.
WARNING
The auto-brake function connot prevent a
collision but instead is intended to reduce
speed at the moment of impact. For full
braking effect, driver must apply the brakes.
NOTE
The auto-brake function is always on and
cannot be turned off.OperationSome settings are controlled from the center
console via a menu system. For information on
how the menu system is used, see page 120.
On and offTo switch Collision Warning on or off, go into
the menu Car settings
Collision warning
settings and select On or Off. When the engine
is started, the setting that was selected when
it was switched off will be used.
Activating/deactivating warning signalsThe collision warning system’s audible and vis-
ual signals are activated automatically when
the engine is started if the collision warning
system is activated.
The audible warning signal can be activated/
deactivated by selecting the alternative
On
or
Off
in Car settings
Collision warning
settings
Warning sound.
Setting a warning distanceThis setting determines the distance at which
the visual and audible warnings are triggered.
Select
Long, Normal
or
Short
under
Car
settings
Collision warning settings
Warning distance
The warning distance determines the level of
sensitivity used by the system. The warning
distance
Long
provides an earlier warning.
Begin by using Long and if the system gives
too many warnings, try changing to
Normal.
WARNING
•
The setting
Short
should only be used
in situations where traffic is light and
moving at low speeds.
•
Collision Warning alerts the driver to the
risk of a collision but this function can-
not reduce the driver’s reaction time.
•
For Collision Warning to be as effective
as possible, it is recommended that Dis-
tance Alert be set to 4 or 5, see
page 173.NOTE
•
When adaptive cruise control is used,
the warning light and signal will be used
by cruise control, even if they have been
deactivated by the driver.
•
In situations where traffic is moving at
considerably different speeds, or if the
vehicle ahead brakes suddenly, warn-
ings may be considered to be late, even
if the setting
Long
has been selected.
Checking settingsThe current Collision Warning settings can be
checked by going into the menu system at Car
settings
Collision warning settings. See
page 120 for more information on the menu
system.

04 Comfort and driving pleasureAdaptive Cruise Control–ACC (option)
04170
•
if the radar sensor is obstructed and can-
not detect other vehicles, for example in
heavy rain, or if snow or other objects are
obscuring the radar sensor.NOTE
Keep the area in front of the radar sensor
clean.•
if the speed of vehicles ahead is signifi-
cantly different from your own speed.WARNING
The radar sensor has a limited field of vision.
In some situations it may detect a vehicle
later than expected or not detect vehicles at
all.
G021414
Radar sensor field of vision (gray)
In certain situations, the radar sensor can-
not detect vehicles at close quarters, for
example a vehicle that suddenly enters thelanes between your vehicle and the one
that the system has already detected.
Small vehicles, such as motorcycles, or
vehicles not driving in the center of the lane
may remain undetected.In curves, the radar sensor may detect the
wrong vehicle or lose a detected vehicle
from view.
Fault tracing and actionsIf the message
Radar blocked See manual
is
displayed, this means that the radar signals
from the sensor have been obstructed and that
a vehicle ahead cannot be detected.
This, in turn, means that the functions of the
ACC, Distance Alert, and Collision Warning
System with Auto-brake will not function.
The table lists possible causes for this mes-
sage being displayed, and suitable actions.
Cause
Action
The surface of the radar in the grille is dirty or obstructed in some way.
Clean the radar surface, or remove the object causing the obstruction.
Heavy rain or snow is interfering with the radar signals.
No action possible. Heavy precipitation may affect the function of the
radar.

04 Comfort and driving pleasure
Adaptive Cruise Control–ACC (option)
04``171
Cause
Action
Swirling water or snow from the surface of the road may interfere with
the radar signals.
No action possible. A very wet or snow-covered road surface may affect
the function of the radar.
The surface of the radar is clean but the message remains in the display.
Wait a short time. It may take several minutes for the radar to detect that
it is no longer obstructed.
Symbols and messages in the displaySymbol
Message
DescriptionStandby mode or active mode when no other vehicle has been detected.Active mode with a detected vehicle to which ACC is adapting speed/distance.Time interval while it is being set.Time interval after it has been set.
Turn on DSTC
to enable Cruise
ACC cannot be activated until the stability system (DSTC) has been activated. see page 155 for more
information on DSTC.
Cruise control canceled
ACC has been automatically switched off.
The driver must regulate the vehicle’s speed/distance to the vehicle ahead.
Cruise control unavailable
ACC cannot be activated. This may be due to:•
high brake temperature
•
the radar sensor is obstructed (by heavy rain, snow, etc.)

04 Comfort and driving pleasure
Driver Alert System (option)
04``177 Operating DAC
Certain settings can be made from the menu
system controlled from the center instrument
panel, see page 120 for more information on
the menu system.
The current system status can be checked on
the trip computer’s display by using the but-
tons on the left steering wheel lever.
G017329
Thumb wheel. Turn this wheel until
Driver
Alert
is displayed. The second line shows
the alternative
Off, Unavailable
, or
[-----]
, i.e., the number of bars.
READbutton. Confirms and erases a mes-
sage in the display.
Activating DACIn the center instrument panel, go to Car
settings Driver Alertand select
On
.
The function is activated when the
vehicle exceeds a speed of 40 mph
(65 km/h). The display will show level
markings of 1–5 bars, where a low
number of bars indicates erratic driving. A high
number of bars indicates stable driving.
If the vehicle is being driven erratically, the
driver will be alerted by an audible signal and
the message Driver Alert, Time for a break is
displayed. The warning will be repeated after a
short time if the driving pattern remains the
same.
WARNING
•
An alert should be taken seriously since
it is sometimes difficult for a driver to
realize that he/she is fatigued.
•
In the event of a warning or if the driver
feels fatigued, stop as soon as possible
in a safe place and rest.

04 Comfort and driving pleasure
Driver Alert System (option)
04``179 Lane Departure Warning (LDW)–
general information
G017394
This function is designed to help reduce the
risk of accidents in situations where the vehicle
leaves its lane and there is a risk of driving off
the road or into the opposite lane. LDW con-
sists of a camera that monitors the lane’s side
marker lines. The driver is alerted by an audible
signal if the vehicle crosses a side marker line
or the road’s center dividing line.
Operation and function
G017426
LDW can be switched on or off by pressing the
button on the center console. A light in the but-
ton illuminates when the function is on.
The trip computer display shows
Lane Depart
Warn Unavailable
when the function is in
standby mode.
When LDW is in standby mode, the function is
activated automatically after the camera has
monitored the road’s side marker lines and the
vehicle’s speed exceeds 40 mph (65 km/h).
Lane Depart Warn Available
will be dis-
played.If the camera can no longer monitor the road’s
side marker lines, or if the vehicle’s speed falls
below 37 mph (60 km/h), LDW will return to
standby mode and
Lane Depart Warn
Unavailable
will be displayed.
If the vehicle unexpectedly crosses the lane’s
left or right side marker lines, the driver will be
alerted by an audible signal.
No warning signal will be given in the follow-
ing situations:
•
The turn signal is being used
•
The driver’s foot is on the brake pedal
1
•
The throttle pedal is pressed quickly
•
If the steering wheel is moved quickly
•
In sharp turns that cause the vehicle’s
body to sway.
See page 162 for information on the camera’s
limitations.WARNING
The driver will only be warned once for each
time the wheels cross a marker line. No
alarm will be given if a marker line is
between the wheels.
1A warning will be given even when
Increased sensitivity
has been selected.

06 Maintenance and specificationsReplacing bulbs
06224
IntroductionAll bulb specifications are listed on page 230.
The following bulbs should only be replaced by
a trained and qualified Volvo service techni-
cian:•
Dome lighting
•
Reading lights
•
Glove compartment lighting
•
Turn signals in the door mirror
•
Approach lighting in the door mirror
•
Brake/fog/taillights
•
Rear side parking lights
•
Active Bi-XenonŸ and LED bulbsNOTE
For information regarding any other bulbs
not mentioned in this section, please con-
tact your Volvo retailer or a trained and
authorized Volvo service technician.
WARNING
•
Active Bi-XenonŸ headlights (option) –
due to the high voltage used by these
headlights, these bulbs should only be
replaced by a trained and qualified
Volvo service technician.
•
Turn off the lights and remove the
remote key from the ignition before
changing any bulbs.
Headlight housing
G010479
G010325
WARNING
•
The engine should not be running when
changing bulbs.
•
When changing in the headlight hous-
ing, if the engine has been running just
prior to replacing bulbs, please be
aware that components in the engine
compartment will be hot.
The entire headlight housing must be lifted out
when replacing all front bulbs (except for the
fog lights).

06 Maintenance and specifications
Replacing bulbs
06``227 Parking lights
G021749
1. Remove the headlight housing from the
vehicle (see page 224).
2. Remove the cover over the bulbs (see
page 225).
3. To access the bulb, first remove the high
beam bulb.
4. Pull the wire to withdraw the bulb holder.
5. Remove the burned out bulb and install a
new one. It can only be secured in one
position.
6. Press the bulb holder into the socket and
press until it clicks into place.
7. Put the cover back into position and rein-
stall the headlight housing.
Turn signals
G021750
1. Remove the headlight housing from the
vehicle (see page 224).
2. Remove the round cover by pulling the tab
until the cover comes off.
3. Pull out the holder to access the bulb.
4. Remove the burned out bulb by pressing it
in slightly and turning out before pulling it
out. Press a new bulb into the socket.
5. Press the bulb holder into the socket and
press until it clicks into place.
6. Press the cover until it clicks into position.
7. Reinstall the headlight housing.
Side marker lights
G021751
NOTE
Before starting to replace a bulb, see
page 224.1. Remove the headlight housing from the
vehicle (see page 224).
2. Remove the round cover.
3. Pull the wire to withdraw the bulb holder.
4. Pull out the burned out bulb and install a
new one. It can only be secured in one
position.
5. Press the bulb holder into the socket and
press until it clicks into place.
6. Press the cover until it clicks into position.

06 Maintenance and specificationsReplacing bulbs
06228
Fog lights
G026015
1. Remove the cover by pressing in the clips
and pulling straight out.
2. Unscrew the fog light housing screw and
pull it out.
3. Turn the bulb counterclockwise and
remove it.
4. Install a new bulb by turning clockwise.
5. Press the bulb into the holder. (The profile
of the bulb holder corresponds to the pro-
file of the foot of the bulb.)
6.
Reinstall the bulb holder. The TOP mark on
the bulb holder must always be upward.
7. Put the cover back into place.
Taillight housing, turn signal
G017456
The bulbs in the taillight cluster are replaced
from inside the cargo area (not the LED func-
tions).
NOTE
Before starting to replace a bulb, see
page 224.1. Open the panel.
2. Remove the insulation by pulling straight
out.
3. Remove the entire bulb unit by turning its
handle counterclockwise.
4. Remove the bulb by pulling it straight out.
Replace the bulb in the reverse order.
Location of taillight bulbs
G017457
Taillight lens, right side
Parking/brake lights (LED)Side maker lights (LED)Turn signalReflectorRear fog light (driver's side only)Backup lightBrake lights (LED)High-mounted brake lights (LED)

06 Maintenance and specifications
Wheels and tires
06``259
CAUTION
The compressor should not be used for
more than 10 minutes at a time to avoid
overheating.9. Turn off the compressor (press the on/off
switch to position 0) when the correct infla-
tion pressure has been reached.
10. Unscrew the hose from the tire’s inflation
valve and reinstall the valve cap.
11. Disconnect the electrical wire from the
12-volt socket.Tire Pressure Monitoring System
(TPMS)–U.S models only
NOTE
USA – FCC ID: KR5S122780002
This device complies with part 15 of the
FCC rules. Operation is subject to the fol-
lowing conditions: (1) This device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that may
cause undesired operation.The tire pressure monitoring system uses sen-
sors mounted in the tire valves to check infla-
tion pressure levels. When the vehicle ismoving at a speed of approximately 20 mph
(30 km/h) or faster, these sensors transmit
inflation pressure data to a receiver located in
the vehicle.
When low inflation pressure is detected, TPMS
will light up the tire pressure warning light
(
) (also referred to as a telltale) in the
instrument panel, and will display a message in
the text window. The wording of this message
is determined by the degree of inflation pres-
sure loss.NOTE
If a fault occurs in TPMS, the tire pressure
warning light will flash for approximately
1 minute and
TIRE PRESS SYST
SERVICE REQUIRED
will be displayed.
Each tire, including the spare (if provided),
should be checked monthly when cold and
inflated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
placard or tire inflation pressure label. (If your
vehicle has tires of a different size than the size
indicated on the vehicle placard or tire inflation
pressure label, you should determine the
proper tire inflation pressure for those tires.)
As an added safety feature, your vehicle has
been equipped with a tire pressure monitoring
system (TPMS) that illuminates a low tire pres-sure telltale when one or more of your tires is
significantly under-inflated. Accordingly, when
the low tire pressure telltale illuminates, you
should stop and check your tires as soon as
possible, and inflate them to the proper pres-
sure. Driving on a significantly under-inflated
tire causes the tire to overheat and can lead to
tire failure. Under-inflation also reduces fuel
efficiency and tire tread life, and may affect the
vehicle's handling and stopping ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv-
er's responsibility to maintain correct tire pres-
sure, even if under-inflation has not reached
the level to trigger illumination of the TPMS low
tire pressure telltale.
Your vehicle has also been equipped with a
TPMS malfunction indicator to indicate when
the system is not operating properly. The
TPMS malfunction indicator is combined with
the low tire pressure telltale. When the system
detects a malfunction, the telltale will flash for
approximately one minute and then remain
continuously illuminated. This sequence will
continue upon subsequent vehicle start-ups as
long as the malfunction exists. When the mal-
function indicator is illuminated, the system
may not be able to detect or signal low tire
pressure as intended. TPMS malfunctions may
occur for a variety of reasons, including the

07 Index
07
283
Starting the vehicle
after a crash (crash mode)....................32
Start inhibitor (immobilizer)........................ 52
Steel grid in cargo area............................ 207
Steering wheel
adjusting............................................... 84
horn....................................................... 84
keypad.................................. 84, 120, 131
Stone chips, touching up......................... 264
Storage spaces........................................ 188
Studded tires........................................... 253
Sunroof (moonroof).............................. 98, 99
Supplemental restraint system.................. 18
warning light......................................... 74TTailgate
driving with it open.............................194
power operated.................................. 202
wiper/washer........................................ 92
Tailgate wipers......................................... 232
Taillights, changing bulbs........................ 228Telephone (cellular), hands-free connec-
tion (Cell phone, hands-free connection). 143
Temporary spare tire...............................254
Three-way catalytic converter................. 200
Tire designations.....................................249
Tire Pressure Monitoring System....259, 260
indicator light........................................ 73
Tires
age...................................................... 245
changing from summer to winter........ 254
glossary of terms................................ 250
improving economy............................ 245
inflation pressure........................ 246, 247
inflation pressure tables.............248, 249
snow...................................................253
spare................................................... 254
specifications...................................... 247
storing................................................. 244
studded............................................... 253
tire pressure monitoring system......... 259
uniform tire quality grading................. 252
Top tether anchors (child restraint sys-
tems).......................................................... 43
Touching up paint.................................... 264
Towing a trailer................................210, 211
trailer hitch.......................................... 211Towing the vehicle........................... 212, 213
Traction control........................................ 155
Trailer towing...................................210, 211
trailer hitch.......................................... 211
Transmission
general description..................... 107, 108
oil........................................................ 274
shiftlock override................................ 108
Tread wear indicator................................ 244
Trip computer.......................................... 152
Trip odometers.......................................... 76
Trips, long distance................................. 195
Turn signals
changing bulbs................................... 227
indicator lights................................73, 88
Two-stage booster cushion....................... 45
UUniform Tire Quality Grading................... 252
Unlocking the vehicle................................. 54
Upholstery care....................................... 263