turn signal bulb VOLVO XC90 2014 Owner´s Manual

02 Instruments and controls
Left-side steering wheel lever
02
71
Lever positions
G026954
Turn signals, lane change position
Turn signals, position for normal turns
High beam flash
Toggle between high and low beams, Home Safe lighting
Turn signals
When turningMove the lever as far up or down as possible (to position 2) to start the turn signals. Theturn signals will be cancelled automatically bythe movement of the steering wheel, or thelever can be returned to its initial position byhand.
When changing lanesThe driver can automatically flash the turnsignals 3 times by:• Moving the turn signal lever up or down to position (1) and releasing it.
• Moving the lever up or down to position(2) and immediately back to its originalposition.
NOTE
• This automatic flashing sequence can be interrupted by immediately movingthe lever in the opposite direction.
• If the turn signal indicator flashesfaster than normal, check for aburned-out turn signal bulb.
High/low beam headlights
Continuous high beams1. Turn the ignition key to position
II.
2. With the light switch in position
,
(see page 67) pull the turn signal lever toward the steering wheel to togglebetween high and low beams.
High beam flash1. Turn the ignition key to position II.
2. Pull the turn signal lever to position (3). The high beams will remain on until thelever is released.
Home safe lightingWhen leaving your vehicle at night, home safelighting can illuminate the area in front of thevehicle.
1. Remove the key from the ignition switch.
2. Pull the turn signal lever as far as possibletoward the steering wheel and release it.
3. Exit the vehicle and lock the doors.The headlights and parking lights will illumi- nate and remain on for 30 1
, 60 or 90 seconds.
The time interval can be changed by a trained and qualified Volvo service technician.
1 Factory setting

09 Maintenance and servicing
Replacing bulbs 09
230* Option/accessory, for more information, see Introduction.
When replacing bulbs, keep the following points in mind:
• Never touch the glass of bulbs with your fingers. Grease and oils from your fingersvaporize in the heat and will leave adeposit on the reflector, which will dam-age it.
• The optional Active Bending Light bulbscontain trace amounts of mercury. Thesebulbs should always be disposed of by anauthorized Volvo retailer.
The following bulbs should only be replaced by a trained and qualified Volvo service tech-nician:
• Active Bending Lights (ABL)
• Daytime running lights (DRL) under the front bumper
• Turn signals and courtesy lights in theside door mirrors
• Reading lights and glove compartmentlight
• Courtesy (dome) lighting
• Rear parking lights
• Brake lights
• High-mounted brake lights
If a problem occurs with the daytime running lights (DRL) under the front bumper, the entirelamp housing will have to be replaced. If a problem occurs with the rear parkinglights or the brake lights, the entire taillighthousing will have to be replaced. See page 236 for a list of bulb specifications.
Replacing high/low beams/turn signal/parking light bulbs
WARNING
•
The engine should not be running when changing bulbs.
• If the engine has been running justprior to replacing bulbs in the head-light housing, please keep in mind thatcomponents in the engine compart-ment will be hot.
WARNING
Active Bending Lights* - due to the high voltage used by these headlights, thesebulbs should only be replaced by a trainedand qualified Volvo service technician.
G027081
The entire lamp housing must be lifted out when replacing these bulbs. To lift out the lamp housing:
1. Switch off the ignition.
2. Open the hood.
3. Pull up the retaining pins (see the illustra-
tion).
4. Lift out the lamp housing.

09 Maintenance and servicing
Replacing bulbs09
}}
* Option/accessory, for more information, see Introduction.231
G027083
Location of the bulbs in the headlight housing
G027082
Low/high beam (models with Active Bending Lights)*, Low beam (models withHalogen headlights)
High beam 1
(models with Halogen head-
lights)
Turn signal
Parking light
Side marker light
Replacing the low beam bulb (halogen headlights)
G027088
1. Remove the plastic cover over the bulb by turning it counterclockwise.
2. Pull the connector from the lamp housing.
3. Loosen the bulb's retaining spring by first moving it to the right and then moving it out of the way.
4. Pull out the bulb from the holder.
5. Insert the new bulb (without touching the glass) in the holder.
1This bulb has no function on models with the optional Active Bending Lights.

09 Maintenance and servicing
Replacing bulbs 09
232
6. Move the retaining spring up and push itslightly to the left until it seats properly.
7. Press the bulb holder into place on the headlight housing.
8. Reinstall the plastic cap. The letters "HAUT " on the cap must be upward.
Replacing the high beam bulb (halogen headlights)
G027085
1. Remove the rubber cover by pulling it off.
2. Pull the connector from the lamp housing.
3. Loosen the bulb's retaining spring by first
moving it to the right and then moving it out of the way. 4. Pull out the bulb from the holder.
5. Insert the new bulb (without touching the
glass) in the holder.
6. Move the retaining spring up and push it slightly to the left until it seats properly.
7. Press the bulb holder into place on the headlight housing.
8. Press the rubber cover into place.
Replacing parking light/side marker light bulbs
G028409
1. Turn the lamp holder approximately 1/4 turn counterclockwise and pull it out of the headlight housing. 2. Pull the bulb straight out.
3. Align the guide lugs on the side of the
base of the new bulb in the grooves in the holder and press it into place.
4. Press the lamp holder into the place in the headlight housing and turn it approxi-mately 1/4 turn clockwise.
Replacing the turn signal bulb
G027089
1. Turn the lamp holder approximately 1/4turn counterclockwise and pull it out of the headlight housing.
2. Press in the bulb slightly and pull it out of the holder.

09 Maintenance and servicing
Replacing bulbs09
233
3. Align the guide lugs on the side of the
base of the new bulb in the grooves in the holder. Press it in and turn it slightlyclockwise.
4. Press the lamp holder into the place in the headlight housing and turn it approxi-mately 1/4 turn clockwise.
Location of taillight bulbs
Turn signal
Backup light
NOTE
If the message indicating a burned out bulb remains in the information displayafter a bulb has been replaced, consult atrained and qualified Volvo service techni-cian.

09 Maintenance and servicing
Replacing bulbs 09
236
Cargo compartment light
1. Carefully insert a screwdriver and pry outthe lens. 2. Pry out the bulb and replace it.
3. Press the lens back into place.
Vanity mirror lights
Removing the lens1. Insert a flat screwdriver under the lens
and carefully exert upward pressure to release the retaining lugs.
2. Snap out the lens.
3. Use needle nose pliers to pull the bulb straight to the side. Replace the bulb. Do not exert too much pressure on the bulbwith the pliers to help avoid damaging it.
Reinserting the lens1. Put the lens back into position.
2. Press it into place.
Bulb specifications
Lighting functionWattageBulb
Low beam (halogen)55H11 LL
High beam (halogen)55H7 LL
Front turn signals21H21W LL

09 Maintenance and servicing
Replacing bulbs09
237
Lighting functionWattageBulb
Front parking lights, front side marker lights, rear courtesy lighting5W5W LL
Turn signals in door mirrors5WY5W LL
Rear fog light21H21W LL
Backup lights21P21W LL
Rear turn signals21PY21W SV
Vanity mirror lighting2W2x4.6d type T5
License plate lighting5C5W LL
Glove compartment5SV8.5 (length 43 mm)
Cargo area lighting10SV8.5 (length 43 mm)
Front footwell lighting5SV8.5 (length 38 mm)
NOTE
Please consult a Volvo retailer’s Parts department for the most up-to-date speci-fications.