start stop button VOLVO XC90 TWIN ENGINE HYBRID 2017 Owners Manual
[x] Cancel search | Manufacturer: VOLVO, Model Year: 2017, Model line: XC90 TWIN ENGINE HYBRID, Model: VOLVO XC90 TWIN ENGINE HYBRID 2017Pages: 584, PDF Size: 14.2 MB
Page 144 of 584
||
INSTRUMENTS AND CONTROLS
142
SymbolMeaning
Oil pressure
If the symbol illuminates duringdriving, stop the vehicle, theengine oil level is too low. Stop theengine immediately and check theengine oil level. Add oil if neces-sary. If the oil level is normal andthe symbol remains illuminated,have the vehicle towed to thenearest authorized Volvo work-shop or trained and qualified Volvoservice technician.
Generator not charging
This symbol illuminates duringdriving if a fault has occurred inthe electrical system. Contact anauthorized Volvo workshop ortrained and qualified Volvo servicetechnician.
AUS modelsBCanadian models
WARNING
•If the fluid level is below the MIN mark inthe brake fluid reservoir or if a warningmessage is displayed in the text window:DO NOT DRIVE. Have the vehicle towedto a trained and qualified Volvo servicetechnician and have the brake systeminspected.
•If the BRAKE and ABS symbols illumi-nate at the same time, there is a risk ofreduced vehicle stability.
Door/hood/tailgate/fuel filler door
reminder
It a door, tailgate, the hood or the fuel filler doorare not closed properly, the information or warn-ing symbol will illuminate and a graphic will bedisplayed in the instrument panel.
Related information
•Instrument panel (p. 132)
•Indicator symbols in the instrument panel(p. 130)
Compass
The rear-view mirror has an integrated compassthat shows the direction in which the vehicle istraveling.
Rearview mirror with compass
Eight different directions are shown with theabbreviations: N (north) NE (northeast) E (east),SE (southeast) S (south), SW (southwest) W(west) NW (northwest)
Switching the compass on/off
The compass is displayed automatically when thevehicle is started or in ignition mode II.
To switch the compass on/off:
–Use a pen, paperclip or similar object andpress in the button on the underside of themirror.
Page 145 of 584
INSTRUMENTS AND CONTROLS
}}
* Option/accessory, for more information, see Introduction.143
Related information
•Calibrating the compass (p. 143)
•Ignition modes (p. 400)
Calibrating the compass
North America is divided into 15 magnetic zonesand the compass will need to be calibrated if thevehicle is driven from one zone to another.
To calibrate the compass:
1.Stop the vehicle in a large open area, safelyout of traffic and away from steel structuresand high-tension electrical wires.
2. Start the vehicle.
NOTE
•For best calibration results, switch off allelectrical equipment in the vehicle (climatesystem, windshield wipers, audio system,etc.) and make sure that all doors areclosed.
•Calibration may not succeed or be incor-rect if the vehicle's electrical equipment isnot switched off.
3. Using a pen, paperclip or similar object, pressand hold the button on the underside of mir-ror for approx. 3 seconds until the number ofthe current magnetic zone is displayed.
15
14
13
12
1198
76
5
4
3
2
1
10
Magnetic zones
4. Press the button on the underside of mirrorrepeatedly until the desired magnetic zone(1–15) is displayed (see the map of mag-netic zones).
5.Wait until C is again displayed in the mirroror hold the button on the underside of mirrorfor approx. 6 seconds until C is displayed inthe mirror.
6.Drive slowly in a circle at a speed of no morethan 6 mph (10 km/h) until a direction is dis-played. This indicates that calibration is com-plete. Drive around in a circle an additionaltwo times to fine-tune the calibration.
7.Vehicles with an electrically heated wind-shield:* if C is displayed when the heatingfunction is activated, perform step 6 with theheating function on.
Page 152 of 584
||
INSTRUMENTS AND CONTROLS
150
NOTE
This function is only active in twilight or darkconditions, and only when the vehicle is inmotion.
Deactivating/activating the function
ABL can be deactivated/activated in two ways inthe center display:
Via Function view
Tap the Active BendingLights button.
Via settings
1.Tap Settings in Top view.
2.Tap My CarLightsExterior Lights.
3.Deselect/select Active Bending Lights.
Related information
•Settings view (p. 115)
Rear fog lights (certain models only)
The rear fog lights12 are considerably brighterthan the normal taillight and should be used onlywhen conditions such as fog, rain, snow, smokeor dust reduce visibility for other vehicles to lessthan approx. 500 ft. (150 meters).
Rear fog light button
NOTE
Rear fog lights are not available on all modelsor in all markets.
The rear fog lights can only be used when:
•the ignition is in mode II or if the engine is
running and the lighting ring is in the
or position
Press the button to turn the fog lights on/off. The
rear fog light indicator symbol in theinstrument panel illuminates when the rear foglights are switched on.
The rear fog lights switch off automatically when:
The rear fog lights turn off automatically whenthe start knob is turned to STOP, or when the
lighting ring is turned to the or posi-tions.
Related information
•Lighting panel and controls (p. 144)
12Some models are equipped with one rear fog light only, on the driver's side of the vehicle.
Page 158 of 584
||
INSTRUMENTS AND CONTROLS
156
The message may be displayed along with graph-ics, symbols or buttons for e.g., confirming themessage or accepting a request.
Service messages
The following table lists a selection of importantservice messages and the action that should betaken.
MessageAction
Stop safelyAStop and switch off theengine. There is a risk ofserious damage to the vehi-
cleB.
Turn off
engineAStop and switch off theengine. There is a risk ofserious damage to the vehi-
cleB.
Serviceurgent Drive
to workshopA
Contact a workshopB to havethe vehicle inspected imme-diately.
Service
requiredAContact a workshopB to havethe vehicle inspected assoon as possible.
Book time formaintenance
Time formaintenance
Time for the next scheduledservice. Contact a work-
shopB.
MessageAction
MaintenanceoverdueTime for the next scheduledservice. Contact a work-
shopB. If the service sched-ule is not followed, this mayvoid all or part of the vehi-cle's warranty and result indamage to vehicle compo-nents.
Temporarily
offAA function has been tempo-rarily deactivated and will bereactivated automaticallywhile driving or after theengine is restarted.
APart of the message is context-dependent.BContact a Volvo retailer or a trained and qualified Volvo servicetechnician.
Center display
Message in the center display's status bar
Messages with lower priority for the driver areshown in the center display.
Most of the messages are shown in the centerdisplay's status bar. The message times out aftera short period of time or disappears if it has beenconfirmed or if action has been taken. Messagesthat need to be stored are saved under My carmessages in Top view.
Some messages in the center display containone or more buttons for e.g., confirming the mes-sage or accepting a request.
Messages' form can vary and they may be dis-played with graphics, symbols or buttons for e.g.,confirming a message or accepting a request.
Page 196 of 584
CLIMATE
* Option/accessory, for more information, see Introduction.194
Starting and stoppingpreconditioning
Preconditioning heats/cools the passenger com-partment prior to driving. Please note that thecharging cable must be connected.
Starting/stopping from the center
display
The preconditioning button in the Parking climate tabin Climate view.
1. Open Climate view in the center display.
2.Tap Parking climate .
The window for seat/steering wheel heating in Climateview's Parking climate tab
3. Tap the boxes to select if seat/steeringwheel heating is to be activated/deactivatedwhen preconditioning starts.
4.Tap Preconditioning.
>Preconditioning starts/stops and the indi-cator lights in the buttons will be on/off.
NOTE
Full preconditioning is only possible when thevehicle's charging cable is connected.
In other cases, the passenger compartmentcan be cooled for 3 minutes in warm weather.This function is started from the Parkingclimate tab in the center display's Climateview.
The vehicle's doors and windows should beclosed during preconditioning.
Starting from a cell phone *
Starting preconditioning and checking the cur-rent settings can be done from a cell phone withthe Volvo On Call mobile app. Preconditioningheats the passenger compartment to a comforta-ble temperature or cools the compartment to thecurrent ambient temperature.
If the vehicle is equipped with the optionalEngine Remote Start (ERS), the air conditioningcan be used to pre-cool the passenger compart-ment to a comfortable temperature.
Related information
•Setting the parking climate (preconditioning)timer (p. 192)
•Activating/deactivating the parking climatetimer (p. 191)
•Hybrid battery charging cable (p. 405)
Page 305 of 584
DRIVER SUPPORT
* Option/accessory, for more information, see Introduction.303
Automatic braking with PilotAssist-1
The auto-hold brakes function as follows withPilot Assist.
Auto-hold brake function
In slow-moving, stop-and-go traffic or when stop-ped at a traffic light, driving will resume automati-cally if the vehicle is not stopped for more thanapprox. 3 seconds. If it takes more than3 seconds for the vehicle ahead to begin movingagain, Pilot Assist will go into standby mode andthe auto-hold brake function will activate.
–The driver will then have to reactivate PilotAssist in one of the following ways:
•Press the button on the left-sidesteering wheel keypad
•Press the accelerator pedal
>Pilot Assist will resume following the vehi-cle ahead (target vehicle) if it begins tomove within approx. 6 seconds.
NOTE
Pilot Assist can keep the vehicle at a stand-still for up to 5 minutes, after which the park-ing brake will be set and Pilot Assist will gointo standby mode.
The parking brake has to be released beforePilot Assist can be reactivated.
Deactivation of the auto-hold brake function
In certain situations, auto-hold will be deactivatedwhen the vehicle is at a standstill and Pilot Assistwill go into standby mode.
This means that the brakes will be released andthe vehicle can begin to roll.
The driver must actively apply the brakes to keepthe vehicle at a standstill.
This can occur in the following situations:
•the driver presses the brake pedal
•the parking brake is set
•the gear selector is moved to the P, N or Rpositions
•the driver puts Pilot Assist in standby mode
Automatically setting the parking brake
In certain situations, the parking brake is setautomatically to help keep the vehicle at a stand-still.
This occurs if:
•the driver unbuckles the seat belt or opensthe door
•Pilot Assist has kept the vehicle at a stand-still for more than approx. 5 minutes
•the engine is turned off
•the brakes overheat
Related information
•Pilot Assist* (p. 295)
•Pilot Assist-1* (p. 295)
•Starting and activating Pilot Assist-1*(p. 298)
•Setting a Pilot Assist-1 time interval (p. 300)
•Deactivating/resuming Pilot Assist-1(p. 301)
•Pilot Assist-1 limitations (p. 304)
Page 372 of 584
||
DRIVER SUPPORT
370
1: Searching and measuring
Parallel parking
Perpendicular parking
PAP searches for a potential parking space andmeasures it to see if there is sufficient space foryour vehicle. To start this procedure:
1. Tap the Park In button inthe center display's Functionview.
If necessary, slow down to:
•a speed below 20 mph (30 km/h) for parallelparking
•approx. 12 mph ( 20 km/h) for perpendicularparking.
2.Keep an eye on the display and be preparedto stop the vehicle when you are instructedby PAP to do so.
3.Select Parallel parking or Perpendicularparking and put the transmission in reverse.
4.Keep an eye on the display and be preparedto stop the vehicle when you are instructedby PAP to do so.
5. Stop the vehicle when instructed to do so.
NOTE
PAP normally searches for available parkingspaces along the curb on the right (passeng-er's) side of the vehicle. However, it can alsoassist in finding and parking in spaces on thedriver's side. To do so:
•Activate the left turn signal. PAP will thensearch for a parking space on the leftside of the vehicle.
2: Backing into the parking space
Parallel parking
Perpendicular parking
Page 395 of 584
STARTING AND DRIVING
}}
393
Opening/closing the fuel filler door
The fuel tank has a filling system that does nothave a cover.
Opening/closing the fuel filler door
An arrow next to the fuel pumpsymbol in the instrument panelindicates the side of the vehiclewhere the fuel filler door islocated.
1. Press the button on the lighting panel.
>Pressure equalization in the fuel tank cau-ses a slight delay before the fuel fillerdoor opens. Fuel tank Fuel lid isopening will be displayed in the instru-ment panel, followed by Fuel tank Readyfor refueling.
2.After refueling, close the fuel filler door bypressing lightly.
Refueling from a service station pump
To refuel:
1.Open the fuel filler door. Do not refuel with
the engine running1
2. Insert the pump's nozzle into the fuel fillerpipe's opening as far as possible (see theillustration).
3. Avoid overfilling the fuel tank. Do not pressthe handle on the filler nozzle after it hasstopped pumping. Too much fuel in the tankin hot weather conditions can cause the fuelto overflow. Overfilling could also cause dam-age to the emission control systems.
1If the engine is running when the vehicle is refueled, the Check Engine Light (malfunction indicator lamp) may indicate a fault. However, your vehicle's performance will not be affected.
Page 413 of 584
STARTING AND DRIVING
}}
411
Pull off the charging socket's protectivecover and place it in the holder on the insideof the door. Be sure that the protective cov-er's rubber plug faces down to help keep thecover from falling out of the holder.
Put the cover back in position and close the doorin reverse order.
Stopping hybrid battery charging
Stop hybrid battery charging by unlocking thevehicle, disconnecting the charging cable fromthe vehicle's charging socket and then unplug-ging the cable from the 120-/240-volt socket.
NOTE
Always unlock the vehicle to stop the charg-ing process before disconnecting the charg-ing cable from the vehicle's charging socketand then unplugging it from the120-/240-volt socket.
The cable must be disconnected from thevehicle's charging socket before it isunplugged from the 120-/240-volt socketto help prevent damage to the chargingsystem.
Unlock the vehicle with the remote key.
Press the release button on the charge cou-pler to release it and disconnect the couplerfrom the vehicle's charging socket. Removethe cable from the vehicle. Put the socket'scover back in place and close the chargerdoor.
Disconnect the cable from the120-/240-volt socket.
Stow the cable in the storage compartmentunder the cargo area floor.
Page 419 of 584
STARTING AND DRIVING
}}
417
Charger status indicators
The red and blue lights in the charging cable'scharge module give an indication of the chargestatus.
Charge module: 1. red warning light, 2. blue status indi-cator
Red warning light
•When the charge module is initially pluggedinto a wall socket, the red warning light willflash once to indicate that a startup safetycheck has been performed. When the safetycheck has been completed, the blue statusindicator will glow steadily and the red warn-ing light will be off.
•If the red warning light continues to flash orglows steadily, a fault has been detected andthe charger will not deliver power to the vehi-cle. Contact a Volvo retailer or a trained andqualified Volvo service technician.
Blue status indicator
•When the charge module is plugged into awall socket, the blue status indicator illumi-nates and glows steadily to show that thecharger is ready to use.
•When the charge coupler (the plug on theother end of the charging cable) has beenplugged into the vehicle's charging socket,the blue status indicator will flash once.
•The blue status indicator will then flashapproximately every two seconds to indicatethat charging is taking place.
•When the indicator light glows steadily, thisindicates that charging has been completed.This will also be indicated by the charginggauge on the instrument panel.
When charging is completed, press the releasebutton on the charge coupler and disconnect itfrom the vehicle.
Unplug the charge module from the wall socket.
Related information
•Hybrid battery charging cable (p. 405)
•Hybrid battery charge status (p. 415)
•Hybrid charging cable circuit breaker(p. 407)
•Hybrid-related symbols and messages(p. 408)
Hybrid battery charging current
Charging current is used to charge the hybridbattery and to precondition the vehicle. Chargingis done through a cable connected between thevehicle's charging socket and a120-/240-volt socket.
When charging is in progress, an indicator light inthe charging socket illuminates to indicate thecharging status. Charging current is primarilyused to recharge the hybrid battery and to pre-condition the vehicle but is also used to rechargethe vehicle's start battery.
CAUTION
Never disconnect the charging cable from the120-/240-volt socket while charging is inprogress. This could damage the socket.
Always stop the charging process (by unlock-ing the vehicle) and disconnect the chargingcable from the vehicle's charging socketbefore disconnecting the other end from the120-/240-volt socket being used.