key YAMAHA AEROX50 2007 User Guide

OPERATION AND IMPORTANT RIDING POINTS
5-4
5
EAU16830
Engine break-in There is never a more important period
in the life of your engine than the period
between 0 and 1000 km (600 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.
EAUM2090
0–150 km (0–90 mi)
Avoid prolonged operation above 1/3
throttle. Vary the speed of the scooter
from time to time. Do not operate it at
one set throttle position.
150–500 km (90–300 mi)
Avoid prolonged operation above 1/2
throttle.
500–1000 km (300–600 mi)
Avoid cruising speeds in excess of 3/4
throttle.
CAUTION:
ECAM1070
After 1000 km (600 mi) of operation,
the final transmission oil must bechanged.
1000 km (600 mi) and beyond
Avoid prolonged full throttle operation.
Vary speeds occasionally.CAUTION:
ECA10270
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealercheck the vehicle.
EAU17212
Parking When parking, stop the engine, and
then remove the key from the main
switch.
WARNING
EWA10310


Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them.


Do not park on a slope or on soft
ground, otherwise the vehiclemay overturn.
CAUTION:
ECA10380
Never park in an area where there
are fire hazards such as grass orother flammable materials.

PERIODIC MAINTENANCE AND MINOR REPAIR
6-20
6 that the breather hose is properly
routed, in good condition, and not
obstructed.
CAUTION:
ECA10600
If the breather hose is positioned in
such a way that the frame is ex-
posed to electrolyte or gas expelled
from the battery, the frame could
suffer structural and external dam-ages.
EAU23501
Replacing the fuse The fuse holder is located behind panel
A. (See page 6-5.)
If the fuse is blown, replace it as fol-
lows.
1. Turn the key to “” and turn off all
electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
CAUTION:
ECA10640
Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly afire.
3. Turn the key to “” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
1. Fuse
Specified fuse:
7.5 A
1
ZAUM0282

CONSUMER INFORMATION
9-1
9
EAU26351
Identification numbers Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.
KEY IDENTIFICATION NUMBER:
VEHICLE IDENTIFICATION
NUMBER:
MODEL LABEL INFORMATION:
EAU26381
Key identification number
The key identification number is
stamped into the key tag. Record this
number in the space provided and use
it for reference when ordering a new
key.
EAU26410
Vehicle identification number
The vehicle identification number is
stamped into the frame.NOTE:
The vehicle identification number is
used to identify your vehicle and may
be used to register it with the licensingauthority in your area.
1. Key identification number
1
ZAUM0070
1. Vehicle identification number1ZAUM0287

INDEX
AAcceleration and deceleration ................ 5-2
Air filter element, cleaning ...................... 6-9BBattery .................................................. 6-18
Brake fluid, changing ............................ 6-15
Brake fluid level, checking .................... 6-15
Brake lever, front .................................... 3-5
Brake lever, rear ..................................... 3-5
Brake levers, lubricating ....................... 6-16
Braking ................................................... 5-3CCarburetor,adjusting ............................. 6-10
Care ........................................................ 7-1
Catalytic converter .................................. 3-7
Centerstand, checking and
lubricating ........................................... 6-16
Coolant ................................................... 6-8
Coolant temperature warning light.......... 3-2
Cowling and panel, removing and
installing ............................................... 6-5DDimmer switch ........................................ 3-4EEngine break-in ...................................... 5-4FFinal transmission oil .............................. 6-7
Front and rear brake lever free play,
checking ............................................. 6-13
Front and rear brake pads, checking .... 6-14
Front fork, checking .............................. 6-17
Fuel......................................................... 3-6
Fuel consumption, tips for reducing........ 5-3
Fuel gauge.............................................. 3-4Fuel tank cap........................................... 3-5
Fuse, replacing...................................... 6-20
HHandlebar switches ................................. 3-4
Headlight bulb, replacing....................... 6-21
High beam indicator light......................... 3-2
Horn switch ............................................. 3-4IIdentification numbers ............................. 9-1
Indicator and warning lights .................... 3-2KKey identification number ........................ 9-1
Kickstarter ............................................... 3-8MMain switch/steering lock ........................ 3-1
Model label .............................................. 9-2OOil level warning light .............................. 3-2PParking ....................................................5-4
Part locations .......................................... 2-1
Periodic maintenance and lubrication
chart ......................................................6-2
Pre-operation check list........................... 4-2RRider seat ................................................ 3-8SSafe-riding points .................................... 1-4
Safety information ...................................1-1
Shock absorber assembly, adjusting
(Depends on models).......................... 3-10
Spark plug, checking ...............................6-6
Specifications .......................................... 8-1
Speedometer unit .................................... 3-3Starting off .............................................. 5-2
Starting the engine.................................. 5-1
Start switch ............................................. 3-4
Steering, checking ................................ 6-17
Storage ................................................... 7-3
Storage compartment A .......................... 3-9
Storage compartment B ........................ 3-10
TTachometer (Depends on models) ......... 3-3
Tail/brake light bulb, replacing .............. 6-21
Throttle cable free play, checking ......... 6-11
Throttle grip and cable, checking and
lubricating ........................................... 6-16
Tires ...................................................... 6-11
Troubleshooting .................................... 6-22
Troubleshooting charts ......................... 6-23
Turn signal indicator light ........................ 3-2
Turn signal light bulb, replacing ............ 6-22
Turn signal switch ................................... 3-4
Two-stroke engine oil.............................. 3-8
Two-stroke engine oil tank ...................... 3-7VVehicle identification number .................. 9-1WWheel bearings, checking..................... 6-18
Wheels .................................................. 6-13