brakes YAMAHA BANSHEE 350 2001 Owners Manual

LOCATION OF THE WARNING AND
SPECIFICATION LABELS .......................1-1
SAFETY INFORMATION .........................2-1
DESCRIPTION AND MACHINE
IDENTIFICATION.....................................3-1
Identification number records ...............3-3
Key identification number .....................3-5
Vehicle identification number ...............3-5
Model label ...........................................3-7
CONTROL FUNCTIONS .........................4-1
Main switch ...........................................4-1
Handlebar switches ..............................4-3
Throttle lever ........................................4-5
Throttle OverRide System ....................4-7
Speed limiter ........................................4-9
Clutch lever ........................................4-11
4
3
2
1Front brake lever ................................4-11
Rear brake pedal ................................4-13
Parking brake .....................................4-13
Shift pedal ..........................................4-17
Kick starter .........................................4-17
Fuel tank cap ......................................4-19
Fuel cock ............................................4-19
Starter (choke)....................................4-21
Seat ....................................................4-23
Front shock absorber adjustment .......4-25
Rear shock absorber adjustment .......4-27
PRE-OPERATION CHECKS ...................5-1
Front and rear brakes ...........................5-5
Fuel ....................................................5-11
Engine mixing oil ................................5-15
Transmission oil .................................5-17
Chain ..................................................5-19
Throttle lever ......................................5-19
5
EBU00015
CONTENTS

2-13
8Never attempt to operate over large obstacles,
such as large rocks or fallen trees. Always fol-
low proper procedures when operating over
obstacles as described in this manual.
8Always be careful when skidding or sliding.
Learn to safely control skidding or sliding by
practicing at low speeds and on level, smooth
terrain. On extremely slippery surfaces, such
as ice, go slowly and be very cautious in order
to reduce the chance of skidding or sliding out
of control.
8Never operate an ATV in fast flowing water or
in water deeper than that recommended in
this manual. Remember that wet brakes may
have reduced stopping ability. Test your
brakes after leaving water. If necessary, apply
them several times to let friction dry out the
linings.
8Always use the size and type tires specified in
this manual.
8Always maintain proper tire pressure as
described in this manual.

4-15
w
8Always set the parking brake before start-
ing the engine. The ATV could start mov-
ing unexpectedly if the parking brake is
not applied. This could cause loss of con-
trol or a collision.
8Always be sure you have released the
parking brake before you begin to ride. The
brake could overheat if you ride the ATV
without releasing the parking brake. You
could lose braking performance which
could cause an accident. You could also
wear out the brakes prematurely.

5-1
EBU00113
PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Brakes9Check operation, free play, fluid level and fluid leakage. 5-5 ~ 5-9
9Fill with DOT 4 (or DOT 3) brake fluid if necessary. 8-73 ~ 8-83
Clutch9Check operation, condition and lever free play. 8-89
Parking brake9Check operation, condition and free play. 8-85 ~ 8-87
Fuel9Check fuel level.
9Fill with fuel if necessary.5-11 ~ 5-13
Transmission oil9Check oil level.
9Fill with oil if necessary.5-17, 8-17 ~ 8-23
Coolant reservoir 9Check coolant level.
9Fill with coolant if necessary.8-23 ~ 8-37
Drive chain9Check chain slack and condition.
9Adjust if necessary.5-19, 8-89 ~ 8-93
Throttle9Check for proper throttle cable operation. 5-19, 8-71
Wheels and tires9Check tire pressure, wear and damage. 5-23 ~ 5-29, 8-101
Fittings and Fasteners9Check all fittings and fasteners. 5-19
Lights9Check for proper operation. 5-21, 8-103 ~ 8-105

5-5
EBU00481
Front and rear brakes
1. Brake lever and brake pedal
Check for correct free play in the front
brake lever. If the free play is incorrect,
adjust it. Check for correct rear brake pedal
height. If the pedal height is incorrect, have
a Yamaha dealer adjust it. (See pages 8-81
~ 8-83.)
Check the operation of the lever and pedal.
They should move smoothly and there
should be a firm feeling when the brakes
are applied. If not, have the machine
inspected by a Yamaha dealer.
2. Brake fluid level
Check the brake fluid level.
Add fluid if necessary. (See pages 8-75 ~
8-79.)
Recommended brake fluid: DOT 4

5-7
NOTE:
If DOT 4 is not available, DOT 3 can be used.
3. Brake fluid leakage
Check to see if any brake fluid is leaking
out of the pipe joints or master cylinders.
Apply the brakes firmly for one minute. If
there is any leaking, have the machine
inspected by a Yamaha dealer.
4. Brake operation
Test the brakes at slow speed after starting
out to make sure they are working properly.
If the brakes do not provide proper braking
performance, inspect the brake pads for
wear.
(See page 8-73.)

5-9
w
Always check the brakes at the start of every
ride. Do not ride the ATV if you find any prob-
lem with the brakes or you could lose braking
ability, which could lead to an accident. If a
problem cannot be corrected by the adjust-
ment procedures provided in this manual,
have the ATV inspected by a Yamaha dealer.

6-19
EBU00208
To decelerate
When slowing down or stopping, release the
throttle and apply the brakes smoothly and
evenly. As you slow down, shift to a lower gear.
Be sure that the engine has sufficiently slowed
before engaging a lower gear. Improper use of
the brakes or shifting can cause the tires to lose
traction, reducing control and increasing the
possibility of an accident.
w
Make sure the engine has sufficiently slowed
before shifting to a lower gear. Engaging a
lower gear when the engine speed is too
high could make the wheels stop rotating.
This could cause loss of control, an accident
and injury. It could also cause engine or
drive train damage.

6-27
EBU00214
Parking on a slope
w
Avoid parking on hills or other inclines.
Parking on a hill or other incline could cause
the ATV to roll out of control, increasing the
chance of an accident. If you must park on
an incline, put the machine in low gear, apply
the parking brake, and block the front and
rear wheels with rocks or other objects.
Do not park the ATV at all on hills that are so
steep you could not walk up them easily.
1. Bring the machine to a stop by applying the
brakes in low gear.
2. Stop the engine and release the clutch
lever.
3. With the front and rear brakes applied, apply
the parking brake and slowly release the
rear brake pedal.

7-35
Select a large, flat area off-road to become
familiar with your ATV. Make sure that this area
is free of obstacles and other riders. You should
practice control of the throttle, brakes, shifting
procedures, and turning techniques in this area
before trying more difficult terrain. Always avoid
riding on paved surfaces: the ATV is designed
for off-road use only, and handling maneuvers
are more difficult to perform on pavement.
Set the parking brake and follow the instruction
on page 6-3 to start the engine. Once it has
warmed up you are ready to begin riding your
ATV. As you get on the ATV, be sure not to
accidentally move the shift pedal. Remember
that the engine and exhaust pipe will be hot
when riding and afterwards; do not allow skin or
clothing to come in contact with these compo-
nents.