tow YAMAHA BANSHEE 350 2005 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2005, Model line: BANSHEE 350, Model: YAMAHA BANSHEE 350 2005Pages: 402, PDF Size: 4.93 MB
Page 70 of 402
4-11
EBU00068
Clutch lever
The clutch lever is located on the left handlebar.
Pull the clutch lever to the handlebar to disen-
gage the clutch, and release the lever to engage
the clutch. The lever should be pulled rapidly and
released slowly for smooth clutch operation.
EBU09880
Brake lever
The brake lever is located on the right handlebar.
Pull it toward the handlebar to apply the front
brake.
q
q
1. Clutch lever1. Levier d’embrayage1. Palanca de embrague
1. Brake lever
1. Levier de frein1. Palanca del freno
5FK-9-66-02 12/3/04 6:36 PM Page 12
Page 142 of 402
6-13
cC
8Do not coast for long periods with the
engine off, and do not tow the machine a
long distance. Even in neutral position, the
transmission is only properly lubricated
when the engine is running. Inadequate
lubrication may cause damage.
8Always use the clutch when changing
gears. The engine, transmission and drive
train are not designed to withstand the
shock of forced shifting and can be dam-
aged by shifting without the clutch.
5FK-9-66-03 11/2/04 10:20 AM Page 14
Page 162 of 402
6-33
EBU00224
Loading
As originally equipped, this ATV is not designed
to carry cargo or tow a trailer. If you choose to
add accessories so that you can carry cargo or
tow a trailer, you must use common sense and
good judgement. Keep the following points in
mind:
8Never exceed the weight limits shown. An
overloaded ATV can be unstable.
MAXIMUM LOADING LIMIT
Vehicle loading limit (total weight of rider,
cargo and accessories): 100 kg
5FK-9-66-03 11/2/04 10:20 AM Page 34
Page 164 of 402
6-35
8Load cargo on the carriers as close to the
center of the vehicle as possible. Put cargo at
the rear of the front carrier and at the front of
the rear carrier. Center the load from side to
side.
8Tie down cargo securely to the carriers. Make
sure cargo in the trailer cannot move around.
A shifting load can cause an accident.
8Make sure the load does not interfere with
controls or your ability to see where you are
going.
8Ride more slowly than you would without a
load. The more weight you carry, the slower
you should go. Although conditions vary, it is
good practice not to exceed 2nd gear when-
ever you are carrying heavier loads or when
towing a trailer.
8Allow more braking distance. A heavier vehi-
cle takes longer to stop.
5FK-9-66-03 11/2/04 10:20 AM Page 36
Page 166 of 402
6-37
8Avoid making sharp turns unless at very slow
speeds.
8Avoid hills and rough terrain. Choose terrain
carefully. Added weight affects the stability
and handling of the ATV.
w
Never exceed the stated load capacity for
this ATV. Overloading this ATV or carrying
or towing cargo improperly could cause
changes in vehicle handling which could
lead to an accident.
Cargo should be properly distributed and
securely attached. Reduce speed when car-
rying cargo or pulling a trailer. Allow greater
distance for braking.
5FK-9-66-03 11/2/04 10:20 AM Page 38
Page 184 of 402
7-17
Speed limiter
For riders inexperienced with this model, this
model is equipped with a speed limiter in the
throttle lever housing. The speed limiter limits
the power and top speed of the ATV. Turning
the adjusting screw in decreases the top speed,
and turning it out increases the top speed. (See
page 4-9 for details.)
Loading and accessories
As originally equipped, this ATV is not designed
to carry cargo or tow a trailer. If you choose to
add accessories so that you can carry cargo or
tow a trailer, you must use common sense and
good judgment.
Use extra caution when riding the ATV with
additional loads, such as accessories or cargo.
The ATV’s handling may be adversely affected.
Reduce your speed when adding additional
loads.
MAXIMUM LOADING LIMIT
Vehicle loading limit (total weight of rider,
cargo and accessories):
100 kg
5FK-9-66-04 4/3/04 1:24 PM Page 18
Page 210 of 402
1. Lean towards inside of turn.
2. Support your weight on the outer footrest.
1. Se pencher vers l’intérieur du virage.
2. S’appuyer sur le repose-pied externe.
1. Inclínese hacia el interior del giro.
2. Descanse su peso en el descansapie externo.
7-43
As you approach a curve, slow down and begin
to turn the handlebars in the desired direction.
As you do so, put your weight on the footboard
to the outside of the turn (opposite your desired
direction) and lean your upper body into the
turn. Use the throttle to maintain an even speed
through the turn. This maneuver will let the
wheel on the inside of the turn slip slightly,
allowing the ATV to make the turn properly.
This procedure should be practiced at slow
speed many times in a large off-road area with
no obstacles. If an incorrect technique is used,
your ATV may continue to go straight. If the ATV
doesn’t turn, come to a stop and then practice
the procedure again. If the riding surface is slip-
pery or loose, it may help to position more of
your weight over the front wheels by moving for-
ward on the seat. Once you have learned this
technique you should be able to perform it at
higher speeds or in tighter curves.
q
w
5FK-9-66-04 4/3/04 1:24 PM Page 44
Page 246 of 402
7-79
8If your ATV is traversing a sloping surface:
Be sure to ride with your weight positioned
towards the uphill side of the ATV to maintain
proper balance. If the ATV starts to tip, steer
down the hill (if there are no obstacles in your
way) to regain balance. If you discover that
the ATV is going to tip over, dismount on the
uphill side. (See pages 7-61–7-63.)
8If your ATV encounters shallow water:
Ride slowly and carefully through slow mov-
ing water, watching for obstacles. Be sure to
let water drain from the ATV and CHECK
YOUR BRAKES FOR PROPER OPERATION
when you come out of the water. Do not con-
tinue to ride your ATV until you have regained
adequate braking ability. (See pages 7-65–
7-67.)
5FK-9-66-04 4/3/04 1:24 PM Page 80
Page 374 of 402
9-3
cC
Excessive water pressure may cause water
seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high pressure deter-
gent applications such as those available in
coin-operated car washers.
4. Once the majority of the dirt has been
hosed off, wash all surfaces with warm
water and mild, detergent-type soap. An
old toothbrush or bottle brush is handy for
hard-to-get-at places.
5. Rinse the machine off immediately with
clean water and dry all surfaces with a
chamois, clean towel or soft absorbent
cloth.
6. Dry the chain and lubricate it to prevent
rust.
5FK-9-66-06 12/3/04 5:54 PM Page 4