weight YAMAHA BIG BEAR PRO 400 2005 User Guide

7-47
CLIMBING UPHILL
Use proper riding techniques to avoid vehicle
overturns on hills. Be sure that you can maneuver
your ATV well on flat ground before attempting any
incline and then practice riding first on gentle
slopes. Try more difficult climbs only after you
have developed your skill. In all cases avoid in-
clines with slippery or loose surfaces, or obstacles
that might cause you to lose control.
WARNING
_ Never operate the ATV on hills too steep for
the ATV or for your abilities. The vehicle can
overturn more easily on extremely steep hills
than on level surfaces or small hills. Practice
on smaller hills before attempting large hills. _ It is important when climbing a hill to make sure
that your weight is transferred forward on the ATV.
This can be accomplished by leaning forward and,
on steeper inclines, standing on the footboards
and leaning forward over the handlebars.
U1C160.book Page 47 Wednesday, May 12, 2004 4:55 PM

7-49
WARNING
_

Always follow proper procedures for
climbing hills as described in this Owner’s
Manual.


Always check the terrain carefully before
you start up any hill.


Never climb hills with excessively slippery
or loose surfaces.


Shift your weight forward.


Never open the throttle suddenly or make
sudden gear changes. The ATV could flip
over backwards.


Never go over the top of any hill at high
speed. An obstacle, a sharp drop, or anoth-
er vehicle or person could be on the other
side of the hill.
_
U1C160.book Page 49 Wednesday, May 12, 2004 4:55 PM

7-51
If you are climbing a hill and you find that you have
not properly judged your ability to make it to the
top, you should turn the ATV around while you still
have forward motion (provided you have the room
to do so) and go down the hill.
WARNING
_ Never attempt to turn the ATV around on any
hill until you have mastered the turning tech-
nique as described in the Owner’s Manual on
level ground. Be very careful when turning on
any hill.
Avoid crossing the side of a steep hill if possi-
ble.
When crossing the side of a hill:

Always follow proper procedures as de-
scribed in the Owner’s Manual.


Avoid hills with excessively slippery or
loose surfaces.


Shift your weight to the uphill side of the
ATV.
_
U1C160.book Page 51 Wednesday, May 12, 2004 4:55 PM

7-55
WARNING
_ Use proper gear and maintain steady speed
when climbing a hill. If you lose all forward
speed:

Keep weight uphill.


Apply the brakes.


Lock the parking brake after you are
stopped.
If you begin rolling backwards:


Keep weight uphill.


Never apply the rear brake while rolling
backwards. Apply the front brake.
When fully stopped, apply the rear brake
as well, and then lock the parking brake.
Dismount on uphill side or to a side if pointed
straight uphill. Turn the ATV around and re-
mount, following the procedure described in
the Owner’s Manual.
_
U1C160.book Page 55 Wednesday, May 12, 2004 4:55 PM

7-57
RIDING DOWNHILL
When riding your ATV downhill, shift your weight
as far to the rear and uphill side of the ATV as pos-
sible. Move back on the seat and sit with your
arms straight. Choose a low gear which will allow
the engine compression to do most of the braking
for you. Improper braking may cause a loss of trac-
tion.
Use caution while descending a hill with loose or
slippery surfaces. Braking ability and traction may
be adversely affected by these surfaces. Improper
braking may also cause a loss of traction.
Whenever possible, ride your ATV straight down-
hill. Avoid sharp angles which could allow the ATV
to tip or roll over. Carefully choose your path and
ride no faster than you will be able to react to ob-
stacles which may appear.
U1C160.book Page 57 Wednesday, May 12, 2004 4:55 PM

7-59
WARNING
_ Always follow proper procedures for going
down hills as described in this Owner’s Manu-
al.
Note: a special technique is required when
braking as you go down a hill.

Always check the terrain carefully before
you start down any hill.


Shift your weight backward.


Never go down a hill at high speed.


Avoid going down a hill at an angle that
would cause the vehicle to lean sharply to
one side.
Go straight down the hill where possible.
_
U1C160.book Page 59 Wednesday, May 12, 2004 4:55 PM

7-61
CROSSING A SLOPE
Traversing a sloping surface on your ATV requires
you to properly position your weight to maintain
proper balance. Be sure that you have learned the
basic riding skills on flat ground before attempting
to cross a sloping surface. Avoid slopes with slip-
pery surfaces or rough terrain that may upset your
balance.
As you travel across a slope, lean your body in the
uphill direction. It may be necessary to correct the
steering when riding on loose surfaces by pointing
the front wheels slightly uphill. When riding on
slopes be sure not to make sharp turns either up or
down hill.
U1C160.book Page 61 Wednesday, May 12, 2004 4:55 PM

7-63
If your ATV does begin to tip over, gradually steer
in the downhill direction if there are no obstacles in
your path. As you regain proper balance, gradually
steer again in the direction you wish to travel.
WARNING
_ Never attempt to turn the ATV around on any
hill until you have mastered the turning tech-
nique as described in the Owner’s Manual on
level ground. Be very careful when turning on
any hill. Avoid crossing the side of a steep hill
if possible.
When crossing the side of a hill:

Always follow proper procedures as de-
scribed in the Owner’s Manual.


Avoid hills with excessively slippery or
loose surfaces.


Shift your weight to the uphill side of the
ATV.
_
U1C160.book Page 63 Wednesday, May 12, 2004 4:55 PM

7-71
SLIDING AND SKIDDING
Care should be used when riding on loose or slip-
pery surfaces since the ATV may slide. If unex-
pected and uncorrected, sliding could lead to an
accident.
To reduce the tendency for the front wheels to
slide in loose or slippery conditions, positioning
your weight over the front wheels will sometimes
help.
If the rear wheels of your ATV start to slide side-
ways, control can usually be regained (if there is
room to do so) by steering in the direction of the
slide. Applying the brakes or accelerating is not
recommended until you have corrected the slide.
U1C160.book Page 71 Wednesday, May 12, 2004 4:55 PM

7-75
WHAT TO DO IF ...
This section is designed to be a reference guide
only. Be sure to read each section on riding tech-
niques completely.
WHAT TO DO ...

If your ATV doesn’t turn when you want it to:
Bring the ATV to a stop and practice the turning
maneuvers again. Be sure you are putting your
weight on the footboard to the outside of the
turn. Position your weight over the front wheels
for better control. (See pages 7-41–7-45.)


If your ATV begins to tip while turning:
Lean more into the turn to regain balance. If
necessary, gradually let off the throttle and/or
steer to the outside of the turn. (See pages
7-41–7-45.)


If your ATV starts to slide sideways:
Steer in the direction of the slide if you have the
room.
Applying the brakes or accelerating is not rec-
ommended until you have corrected the slide.
(See pages 7-71–7-73.)
U1C160.book Page 75 Wednesday, May 12, 2004 4:55 PM