light YAMAHA BLASTER 200 2002 Manuale de Empleo (in Spanish)

8-77
2. Remove the bulb holder cover, turn the bulb
holder counterclockwise and remove the
defective bulb.
w
The headlight bulb is hot when it is on and
immediately after it is turned off. Wait for the
bulb to cool before touching or removing it.
You can be burned, or a fire could start if the
bulb touches something flammable.
3. Put a new bulb into position and secure it in
place with the bulb holder.
4. Install the bulb holder cover.
cC
Make sure the bulb holder cover is securely
fitted over the bulb holder and seated
against the reflector.
5. Install the headlight unit assembly.
Adjust the headlight beam if necessary.
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 78

8-79
EBU00411
Headlight beam adjustment
cC
It is advisable to have a Yamaha dealer make
this adjustment.
Vertical adjustment:
Loosen the headlight assembly mounting bolts
and adjust the vertical beam by moving the
headlight up or down.
q
q
1. Mounting bolt (× 2)1. Boulon de montage (× 2)1. Tornillo de montaje (× 2)
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 80

8-81
EBU00861
Tail/brake light bulb replacement
1. Remove the bulb holder (together with the
bulb) by turning it counterclockwise.
2. Remove the defective bulb from the bulb
holder by pushing it inward and turning it
counterclockwise.
3. Install a new bulb in the bulb holder by
pushing it inward and turning it clockwise.
4. Install the bulb holder (together with the
bulb).
q
q
w
1. Bulb holder1. Fixation d’ampoule1. Portabombillas
1. Bulb holder 2. Bulb
1. Fixation d’ampoule 2. Ampoule
1. Portabombillas 2. Bombilla
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 82

8-85
w
Do not smoke when checking the fuel sys-
tem. Fuel can ignite or explode, causing
severe injury or property damage. Make sure
there are no open flames or sparks in the
area, including pilot lights from water
heaters or furnaces.
5KJ-62 (8 shou) 4/23/01 3:08 PM Page 86

9-9
4. Lubricate all control cables.
5. Block up the frame to raise all wheels off the
ground.
6. Tie a plastic bag over the exhaust pipe out-
let to prevent moisture from entering.
7. If storing in a humid or salt-air atmosphere,
coat all exposed metal surfaces with a light
film of oil. Do not apply oil to any rubber
parts or the seat cover.
NOTE:
Make any necessary repairs before storing the
machine.
5KJ-62 (9 shou ~) 4/23/01 3:09 PM Page 10

10-5
Model YFS200
Suspension:
Front suspension Double wishbone
Rear suspension Swingarm (monocross)
Shock absorber:
Front shock absorber Coil spring/Oil damper
Rear shock absorber Coil spring/Gas-oil damper
Wheel travel:
Front wheel travel 180 mm
Rear wheel travel 180 mm
Electrical:
Ignition system C.D.I.
Generator system C.D.I. magneto
Headlight type: Bulb type
Bulb voltage, wattage ×quantity:
Headlight 12V, 45 W/45 W ×1
Tail/brake light 12V, 5/21 W ×1
Indicator light:
Oil level 12V, 3.4 W ×1
5KJ-62 (9 shou ~) 4/23/01 3:09 PM Page 16