oil YAMAHA BLASTER 200 2003 Owner's Manual

8-81
EBU00570
Cable inspection and lubrication
w
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer
covering of control cables becomes dam-
aged. Cables can also become frayed or
kinked. Operation of controls could be
restricted, which could cause an accident or
injury.
Lubricate the inner cables and the cable ends. If
the cables do not operate smoothly, ask a
Yamaha dealer to replace them.
Recommended lubricant:
Engine oil
5VM-9-60 (8 shou) 6/20/02 4:23 PM Page 82

a
22
11
cC
Do not touch the glass part of the headlight
bulb to keep it free from oil, otherwise the
transparency of the glass, the luminosity of
the bulb, and the bulb life will be adversely
affected. Thoroughly clean off any dirt and
fingerprints on the headlight bulb using a
cloth moistened with alcohol or thinner.
8. Install the headlight bulb holder cover.
cC
Make sure the headlight bulb holder cover is
securely fitted over the bulb holder.
9. Install the headlight unit assembly by
installing the screws.
a. Do not touch the glass part of the bulb.a. Ne pas toucher le verre de l’ampoule.a. No toque la parte de vidrio de la bombilla.
8-95 1. Headlight unit assembly 2. Screw (×2)
1. Optique de phare 2. Vis (×2)1. Unidad del faro 2. Tornillo (×2)
5VM-9-60 (8 shou) 6/20/02 4:23 PM Page 96

9-7
EBU00528
B. STORAGE
Long term storage (60 days or more) of your
machine will require some preventive proce-
dures to guard against deterioration. After thor-
oughly cleaning the machine, prepare for stor-
age as follows:
1. Fill the fuel tank with fresh fuel and add fuel
stabilizer (if available).
NOTE:
Use of fuel stabilizer eliminates the need to
drain the fuel system. Consult a Yamaha dealer
if the fuel system is to be drained instead.
2. Remove the spark plug, pour about one
tablespoon of SAE 10W30 or 20W40 motor
oil in the spark plug hole and reinstall the
spark plug. Ground the spark plug wire and
turn the engine over several times to coat
the cylinder wall with oil.
3. Clean the drive chain thoroughly and lubri-
cate it. (See page 8-77.)
5VM-9-60 (9 shou ~) 6/21/02 11:14 AM Page 8

9-9
4. Lubricate all control cables.
5. Block up the frame to raise all wheels off the
ground.
6. Tie a plastic bag over the exhaust pipe out-
let to prevent moisture from entering.
7. If storing in a humid or salt-air atmosphere,
coat all exposed metal surfaces with a light
film of oil. Do not apply oil to any rubber
parts or the seat cover.
NOTE:
Make any necessary repairs before storing the
machine.
5VM-9-60 (9 shou ~) 6/21/02 11:14 AM Page 10

10-1
Model YFS200
Dimensions:
Overall length 1,735 mm
Overall width 1,035 mm
Overall height 1,040 mm
Seat height 740 mm
Wheelbase 1,100 mm
Ground clearance 120 mm
Minimum turning radius 3,000 mm
Basic weight:
With oil and full fuel tank 155 kg
Engine:
Engine type Air-cooled 2-stroke
Cylinder arrangement Forward-inclined single cylinder
Displacement 195 cm
3
Bore × stroke 66 ×57 mm
Compression ratio 6.6 : 1
Starting system Kick starter
Lubrication system Separate lubrication (Yamaha Autolube)
EBU00428
SPECIFICATIONS
5VM-9-60 (9 shou ~) 6/21/02 11:14 AM Page 12

10-2
Model YFS200
Engine oil (2-cycle):
Type Air-cooled 2-stroke engine oil
Quantity 1.3 L
Transmission oil:
Type SAE 10W30 type SE motor oil
Recommended transmission oil
classificationAPI Service SE, SF, SG type or higher
cC
In order to prevent clutch slippage (since the
transmission oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD” or
oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING
II” or higher.
Quantity:
Periodic oil change 0.65 L
Total amount 0.7 L
Air filter Wet type element
10
5VM-9-60 (9 shou ~) 6/21/02 11:14 AM Page 13

10-5
Model YFS200
Suspension:
Front suspension Double wishbone
Rear suspension Swingarm (monocross)
Shock absorber:
Front shock absorber Coil spring/Oil damper
Rear shock absorber Coil spring/Gas-oil damper
Wheel travel:
Front wheel travel 180 mm
Rear wheel travel 180 mm
Electrical:
Ignition system C.D.I.
Generator system C.D.I. magneto
Headlight type: Bulb type
Bulb voltage, wattage ×quantity:
Headlight 12V, 35 W/36.5 W ×1
Tail/brake light 12V, 5/21 W ×1
Oil level warning light 12V, 3.4 W ×1
5VM-9-60 (9 shou ~) 6/21/02 11:14 AM Page 16

10-15
Modelo YFS200
Suspensión:
Suspensión delantera Brazo oscilante doble
Suspensión trasera Brazo oscilante (monocross)
Amortiguador:
Amortiguador delantero Resorte en espiral/Amortiguador de aceite
Amortiguador trasero Resorte en espiral/Amortiguador de gasoil
Trayectoria de la rueda:
Trayectoria de la rueda frontal 180 mm
Trayectoria de la rueda trasera 180 mm
Sistema eléctrico:
Sistema de encendido C.D.I.
Sistema de generador Magneto de C.D.I.
Tipo del faro: Tipo de bombilla
Voltaje, vataje de bombilla ×cantidad:
Faro 12V, 35 W/36.5 W ×1
Luz de cola/freno 12V, 5/21 W ×1
Luz de aviso del nivel del aceite 12V, 3,4 W ×1
5VM-9-60 (9 shou ~) 6/21/02 11:14 AM Page 26