lights YAMAHA BLASTER 200 2005 Manuale de Empleo (in Spanish)

LOCATION OF THE WARNING AND
SPECIFICATION LABELS .......................1-1
SAFETY INFORMATION .........................2-1
DESCRIPTION AND MACHINE
IDENTIFICATION.....................................3-1
Identification number records ...............3-3
Key identification number .....................3-5
Vehicle identification number ...............3-7
Model label ...........................................3-9
CONTROL FUNCTIONS..........................4-1
Main switch ...........................................4-1
Indicator lights ......................................4-3
Oil level warning light checking
method ...............................................4-5
Handlebar switches ..............................4-9Throttle lever ......................................4-11
Throttle OverRide System ..................4-13
Speed limiter ......................................4-15
Clutch lever ........................................4-17
Brake lever .........................................4-17
Brake pedal ........................................4-19
Parking brake .....................................4-19
Shift pedal ..........................................4-23
Kick starter .........................................4-23
Fuel tank cap ......................................4-25
Fuel cock ............................................4-25
Starter (choke) ....................................4-27
Seat ....................................................4-29
Front shock absorber adjustment .......4-31
Rear shock absorber adjustment .......4-33
PRE-OPERATION CHECKS ...................5-1
Front and rear brakes ...........................5-5
Fuel ......................................................5-9
EBU00015
CONTENTS
1
2
3
4
5
5VM-9-62-01 3/12/04 2:33 PM Page 12

Engine oil ............................................5-13
Transmission oil .................................5-15
Chain ..................................................5-17
Throttle lever ......................................5-17
Fittings and fasteners .........................5-17
Lights ..................................................5-19
Switches .............................................5-19
Tires ...................................................5-21
How to measure tire pressure ............5-25
Tire wear limit .....................................5-27
OPERATION ............................................6-1
Starting a cold engine ...........................6-3
Starting a warm engine ........................6-9
Warming up ..........................................6-9
Shifting ...............................................6-11
To start out and accelerate .................6-15
To decelerate .....................................6-19
Engine break-in ..................................6-21
Parking ...............................................6-25
Parking on a slope ..............................6-27Accessories and loading ....................6-29
RIDING YOUR ATV .................................7-1
Getting to know your ATV.....................7-3
Ride with care and good
judgement ...........................................7-5
Be careful where you ride ...................7-27
Turning your ATV ...............................7-43
Climbing uphill ....................................7-47
Riding downhill ...................................7-59
Crossing a slope .................................7-63
Crossing through shallow water .........7-67
Riding over rough terrain ....................7-71
Sliding and skidding ...........................7-73
What to do if .......................................7-77
What to do ..........................................7-77
PERIODIC MAINTENANCE AND
ADJUSTMENT.........................................8-1
Owner’s manual and tool kit .................8-3
Periodic maintenance/Lubrication ........8-7
Transmission oil .................................8-17
6
7
8
5VM-9-62-01 3/12/04 2:33 PM Page 13

2-15
8Always maintain proper tire pressure as
described in this manual.
8Never modify an ATV through improper instal-
lation or use of accessories.
8Never exceed the stated load capacity for an
ATV. Cargo should be properly distributed
and securely attached. Reduce speed and fol-
low instructions in this manual for carrying
cargo or pulling a trailer. Allow greater dis-
tance for braking.
w
8Always turn off the engine when refueling.
8Do not refuel immediately after the engine
has been running and is still very hot.
8Do not spill gasoline on the engine or
exhaust pipe/muffler when refueling.
Never refuel while smoking or in the vicini-
ty of sparks, open flames, or other
sources of ignition such as the pilot lights
of water heaters and clothes dryers.
Gasoline can catch fire. You could be
burned.
5VM-9-62-01 3/12/04 2:33 PM Page 50

4-3
EBU00043
Indicator lights
EBU01274
Oil level warning light “7”
This light comes on when the oil level is low.
The light circuit can be checked by the following
procedure.
cC
Always make sure there is enough engine oil
before starting the engine.
1
1. Oil level warning light “7”1. Témoin d’avertissement du niveau d’huile “7”1. Luz de aviso del nivel del aceite “7”
5VM-9-62-02 3/12/04 4:13 PM Page 4

4-9
EBU00053
Handlebar switches
EBU01158
Engine stop switch “ENG. STOP”
Make sure that the engine stop switch is in the
“RUN” position before starting the engine. The
engine stop switch controls ignition and can be
used at all times to stop the engine, especially in
an emergency. The engine will not start or run
when the engine stop switch is turned to “OFF”.
EBU01286
Light switch “LIGHTS”
Set the switch to the “LO” position to switch on
the low beam and the taillight.
Set the switch to the “HI” position to switch on
the high beam and the taillight.
Set the switch to the “OFF” position to switch off
all the lights
NOTE:
The headlight and the taillight can be turned on
only when the engine is started.
q
w
1. Light switch “LIGHTS”
2. Engine stop switch “ENG. STOP”
1. Contacteur d’éclairage “LIGHTS”
2. Coupe-circuit du moteur “ENG. STOP”
1. Interruptor de luce “LIGHTS”
2. Interruptor de paro del motor “ENG. STOP”
5VM-9-62-02 3/12/04 4:13 PM Page 10

4-10
FBU00053
Contacteurs au guidon
FBU01158
Coupe-circuit du moteur “ENG. STOP”
S’assurer que le coupe-circuit du moteur est placé
sur “RUN” avant de mettre le moteur en marche.
Le coupe-circuit du moteur contrôle l’allumage et
peut à tout moment servir à couper le moteur. Il
est particulièrement utile en cas d’urgence. Le
moteur ne se met pas en marche ou ne tourne pas
quand son coupe-circuit est sur “OFF”.
FBU01286
Contacteur d’éclairage “LIGHTS”
Placer le contacteur à la position “LO” pour
allumer le feu de croisement et le feu arrière.
Placer le contacteur à la position “HI” pour allu-
mer le feu de route et le feu arrière.
Placer le contacteur sur “OFF” pour éteindre
tous les feux.
N.B.:
Le phare et le feu arrière ne s’allument que
lorsque le moteur tourne.
SBU00053
Interruptores del manillar
SBU01158
Interruptor de parada del motor “ENG.
STOP”
Asegúrese de que el interruptor de parada del
motor esté en la posición “RUN” antes de arrancar
el motor. El interruptor de parada del motor con-
trola el encendido y puede utilizarse para parar el
motor en cualquier momento, especialmente en
casos de emergencia. Cuando se gira el interrup-
tor de parada a la posición “OFF”, el motor no
puede ser puesto en marcha ni funcionar.
SBU01286
Interruptor de luces “LIGHTS”
Ponga el interruptor a la posición “LO” para
encender la luz de cruce y la luz de cola.
Ponga el interruptor a la posición “HI” para
encender la luz de carretera y la luz de cola.
Ponga el interruptor a la posición “OFF” para
apagar todas las luces.
NOTA:
El faro y la luz de cola sólo pueden encenderse
cuando se ha puesto en marcha el motor.
5VM-9-62-02 3/12/04 4:13 PM Page 11

5-1
EBU00113
PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Brakes9Check operation, free play, fluid level and fluid leakage. 5-5–5-7
9Fill with DOT 4 brake fluid if necessary. 8-55–8-63
Clutch9Check operation, condition and lever free play. 8-71
Parking brake9Check operation, condition and cable free play. 8-65–8-67
Fuel 9Check fuel level.
9Fill with fuel if necessary.5-9–5-11
Transmission oil9Check oil level.
9Fill with oil if necessary.5-15, 8-17–8-23
2-cycle engine oil9Check oil level.
9Fill with oil if necessary.5-13
Drive chain9Check chain slack and condition.
9Adjust if necessary.5-17, 8-73–8-79
Throttle9Check for proper throttle cable operation. 5-17, 8-53
Wheels and tires9Check tire pressure, wear and damage. 5-21–5-27, 8-87
Fittings and fasteners9Check all fittings and fasteners. 5-17
Lights and switches9Check for proper operation. 5-19, 8-89–8-99
5VM-9-62-02 3/12/04 4:13 PM Page 38

5-19
EBU00803
Lights
Check the headlight and tail/brake light to make
sure they are in working condition. Repair as
necessary for proper operation.
EBU01170
Switches
Check the operation of all switches. Have a
Yamaha dealer repair as necessary for proper
operation.
5VM-9-62-02 3/12/04 4:13 PM Page 56

8-103
w
Do not smoke when checking the fuel sys-
tem. Fuel can ignite or explode, causing
severe injury or property damage. Make sure
there are no open flames or sparks in the
area, including pilot lights from water
heaters or furnaces.
5VM-9-62-05 3/12/04 4:15 PM Page 104