oil level YAMAHA BLASTER 200 2005 Owners Manual

LOCATION OF THE WARNING AND
SPECIFICATION LABELS .......................1-1
SAFETY INFORMATION .........................2-1
DESCRIPTION AND MACHINE
IDENTIFICATION.....................................3-1
Identification number records ...............3-3
Key identification number .....................3-5
Vehicle identification number ...............3-7
Model label ...........................................3-9
CONTROL FUNCTIONS..........................4-1
Main switch ...........................................4-1
Indicator lights ......................................4-3
Oil level warning light checking
method ...............................................4-5
Handlebar switches ..............................4-9Throttle lever ......................................4-11
Throttle OverRide System ..................4-13
Speed limiter ......................................4-15
Clutch lever ........................................4-17
Brake lever .........................................4-17
Brake pedal ........................................4-19
Parking brake .....................................4-19
Shift pedal ..........................................4-23
Kick starter .........................................4-23
Fuel tank cap ......................................4-25
Fuel cock ............................................4-25
Starter (choke) ....................................4-27
Seat ....................................................4-29
Front shock absorber adjustment .......4-31
Rear shock absorber adjustment .......4-33
PRE-OPERATION CHECKS ...................5-1
Front and rear brakes ...........................5-5
Fuel ......................................................5-9
EBU00015
CONTENTS
1
2
3
4
5
5VM-9-62-01 3/12/04 2:33 PM Page 12

4-3
EBU00043
Indicator lights
EBU01274
Oil level warning light “7”
This light comes on when the oil level is low.
The light circuit can be checked by the following
procedure.
cC
Always make sure there is enough engine oil
before starting the engine.
1
1. Oil level warning light “7”1. Témoin d’avertissement du niveau d’huile “7”1. Luz de aviso del nivel del aceite “7”
5VM-9-62-02 3/12/04 4:13 PM Page 4

4-5
EBU00757
Oil level warning light checking method
Start the engine.
Wait a few seconds.
Engine oil level and
electrical circuit are OK.Supply engine oil.
Oil level warning light
does not come on
(see NOTE).
Ask a Yamaha dealer to
inspect the electrical circuit.
NOTE:
If the main switch is turned off after the oil level
warning light goes off and the engine is immedi-
ately started again, the oil level warning light
may not come on. This does not indicate a cir-
cuit failure.
Turn the main switch to
“ON” and the engine
stop switch to“RUN”.
Oil level warning
light comes on.
The oil level warning
light stays on.The oil level warning light
goes off.
5VM-9-62-02 3/12/04 4:13 PM Page 6

5-1
EBU00113
PRE-OPERATION CHECKS
Before using this machine, check the following points:
ITEM ROUTINE PAGE
Brakes9Check operation, free play, fluid level and fluid leakage. 5-5–5-7
9Fill with DOT 4 brake fluid if necessary. 8-55–8-63
Clutch9Check operation, condition and lever free play. 8-71
Parking brake9Check operation, condition and cable free play. 8-65–8-67
Fuel 9Check fuel level.
9Fill with fuel if necessary.5-9–5-11
Transmission oil9Check oil level.
9Fill with oil if necessary.5-15, 8-17–8-23
2-cycle engine oil9Check oil level.
9Fill with oil if necessary.5-13
Drive chain9Check chain slack and condition.
9Adjust if necessary.5-17, 8-73–8-79
Throttle9Check for proper throttle cable operation. 5-17, 8-53
Wheels and tires9Check tire pressure, wear and damage. 5-21–5-27, 8-87
Fittings and fasteners9Check all fittings and fasteners. 5-17
Lights and switches9Check for proper operation. 5-19, 8-89–8-99
5VM-9-62-02 3/12/04 4:13 PM Page 38

5-13
EBU00134
Engine oil
Make sure the engine oil is at the specified level.
Add oil as necessary (see page 10-2).
NOTE:
Be sure to push the cap into the filler neck until it
is properly seated.
q
1. Oil tank filler cap1. Bouchon de remplissage de réservoir d’huile1. Tapa de llenado de depósito de aceite
Recommended oil:
Air-cooled 2-stroke engine oil
Oil quantity:
Total amount:
1.3 L
5VM-9-62-02 3/12/04 4:13 PM Page 50

5-15
EBU12891
Transmission oil
Make sure the transmission oil is at the specified
level. Add oil as necessary. (See pages 8-17–
8-23.)
cC
8In order to prevent clutch slippage (since
the transmission oil also lubricates the
clutch), do not mix any chemical additives.
Do not use oils with a diesel specification of
“CD” or oils of a higher quality than speci-
fied. In addition, do not use oils labeled
“ENERGY CONSERVING
II” or higher.
8Make sure that no foreign material enters
the crankcase.
Recommended oil type and quantity:
See page 10-2.
5VM-9-62-02 3/12/04 4:13 PM Page 52

8-9
NOTE:
8Recommended brake fluid: DOT 4
8Brake fluid replacement:
9When disassembling the master cylinders or caliper cylinders, replace the brake fluid.
Normally check the brake fluid level and add fluid as required.
9On the inner parts of the master cylinders and caliper cylinders, replace the oil seals every
two years.
9Replace the brake hoses every four years, or if cracked or damaged.
5VM-9-62-05 3/12/04 4:15 PM Page 10

EBU08371
Transmission oil
Transmission oil measurement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes,
and stop it.
3. Check the oil level through the level window
located at the right side crankcase cover.
NOTE:
Wait a few minutes until the oil level settles
before checking.
4. The oil level should be between the mini-
mum and maximum marks. If the level is
low, add the recommended oil to raise it to
the proper level.
1
2
3
1
1. Level window
2. Maximum level mark 3. Minimum level mark
1. Hublot de contrôle du niveau d’huile
2. Repère de niveau maximum 3. Repère de niveauminimum
1. Mirilla del nivel
2. Marca de máximo 3. Marca de mínimo
8-17
5VM-9-62-05 3/12/04 4:15 PM Page 18

q
1. Drain bolt1. Boulon de vidange1. Perno de drenaje
8-19
Transmission oil replacement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes,
and stop it.
3. Place a container under the engine to col-
lect the used oil.
4. Remove the oil filler cap and drain bolt to
drain the oil.
5. Install the drain bolt and tighten it to the
specified torque.
6. Fill the engine with the recommended oil
and install the filler cap.
1
1. Transmission oil filler cap1. Bouchon de remplissage d’huile1. Tapón de llenado del aceite
Tightening torque
Drain bolt:
20 Nm (2.0 m0kgf)
5VM-9-62-05 3/12/04 4:15 PM Page 20

8-23
7. Start the engine and warm it up for a few
minutes. While warming up, check for oil
leakage. If oil leakage is found, stop the
engine immediately, and check for the
cause.
8. Check the oil level.
5VM-9-62-05 3/12/04 4:15 PM Page 24