maintenance reset YAMAHA CYGNUS 125 2000 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2000, Model line: CYGNUS 125, Model: YAMAHA CYGNUS 125 2000Pages: 76, PDF Size: 1.3 MB
Page 42 of 76
6-8
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRZAUM00**
1
1. Spark plug gap
Spark plug gap:
0.6~0.7 mm (0.024~0.028 in)
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
3. Install the spark plug with the spark
plug wrench, and then tighten it to
the specified torque.
Tightening torque:
Spark plug:
13 Nm (1.3m kgf, 9.4ft lbf)
NOTE:
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4~1/2 turn past
finger tight. However, the spark plug
should be tightened to the specified
torque as soon as possible.4. Install the spark plug cap.
5. Install the panel.
EAUT1350
Engine oil and oil strainerThe engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil strainer cleaned
at the intervals specified in the periodic
maintenance and lubrication chart. The
engine oil must also be changed at the
initial 1000 km (600 mi) and when the
oil change indicator changes from green
to red. The oil change indicator must be
reset after the initial 1000 km (600 mi).
(See page 3-2 for reset procedures.)
To check the engine oil level
1.Place the vehicle on the centerstand.NOTE:
Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.2. Start the engine, warm it up for sev-
eral minutes, and then turn it off.
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, inser t it
back into the oil filler hole (without
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 8
Page 44 of 76
6-10
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
and engine oil drain bolts, and then
tighten the drain bolts to the speci-
fied torque.
Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m kgf, 14.5ft lbf)
Engine oil drain bolt B:
20 Nm (2.0 m kgf, 14.5 ft lbf)
NOTE:
Make sure that the O-ring is properly
seated.7. Add the specified amount of the
recommended engine oil, and then
install and tighten the engine oil filler
cap.
Recommended engine oil:
See page 8-1.
Oil change quantity:
0.9 L (0.98 US qt) (0.83 Imp.qt)
ECA11670
cC8 88 8
8Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. Inaddition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
8 88 8
8Be sure no foreign material en-
ters the crankcase.
8. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
9. Turn the engine off, and then check
the oil level and correct it if neces-
sary.
10. Reset the oil change indicator. (See
page 3-2 for reset procedures.)NOTE:
If the engine oil is changed before the
oil change indicator changes to red (i.e.
before the periodic oil change interval
has been reached), the indicator must
be reset after the oil change for the next
periodic oil change to be indicated at the
correct time.
EAU20060
Final transmission oilThe final transmission case must be
checked for oil leakage before each ride.
If any leakage is found, have a Yamaha
dealer check and repair the scooter. In
addition, the final transmission oil must
be changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several min-
utes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 10