fuel YAMAHA FJR1300A 2003 User Guide

PERIODIC MAINTENANCE AND MINOR REPAIR
6-3
6
9
*Wheels
Check runout and for damage.√√√√
10*TiresCheck tread depth and for damage.
Replace if necessary.
Check air pressure.
Correct if necessary.√√√√ √
11*Wheel bearings
Check bearing for looseness or damage.√√√√
12*SwingarmCheck operation and for excessive play.√√√√
Lubricate with lithium-soap-based grease. Every 50,000 km
13*Steering bearingsCheck bearing play and steering for roughness.√√√√√
Lubricate with lithium-soap-based grease. Every 20,000 km
14*Chassis fasteners
Make sure that all nuts, bolts and screws are properly tightened.√√√√ √
15 Sidestand/centerstandCheck operation.
Lubricate.√√√√ √
16*Sidestand switch
Check operation.√√√√√ √
17*Front fork
Check operation and for oil leakage.√√√√
18*Shock absorber assembly
Check operation and shock absorber for oil leakage.√√√√
19*Rear suspension relay
arm and connecting arm
pivoting pointsCheck operation.√√√√
20*Electronic fuel injection
Adjust engine idling speed and synchronization.√√√√√ √
21 Engine oilChange.
Check oil level and vehicle for oil leakage.√√√√√ √ NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (×
1,000 km)
ANNUAL
CHECK
1 10203040
U5JWE2.book Page 3 Wednesday, November 6, 2002 3:32 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-17
6
EAU00635
Adjusting the throttle cable
free play The throttle cable free play should
measure 3–5 mm at the throttle grip.
Periodically check the throttle cable
free play and, if necessary, have a
Yamaha dealer adjust it.
EAU00637
Adjusting the valve clearance The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
EAU00658
Tires To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
EW000082
WARNING
_

The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).


The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.
_
a. Throttle cable free playU5JWE2.book Page 17 Wednesday, November 6, 2002 3:32 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-32
6
EC000102
CAUTION:_

Always keep the battery
charged. Storing a discharged
battery can cause permanent
battery damage.


To charge a sealed-type (MF)
battery, a special (constant-
voltage) battery charger is re-
quired. Using a conventional
battery charger will damage the
battery. If you do not have ac-
cess to a sealed-type (MF) bat-
tery charger, have a Yamaha
dealer charge your battery.
_
EAU05025
Replacing the fuses The fuse box, which contains the fuses
for the individual circuits, is located un-
der panel A. Both the electronic fuel in-
jection fuse and the main fuse are
located under panel D. The main fuse
is located beside the battery. (See pag-
es 6-6 and 6-7 for panel removal and
installation procedures.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.1. Electronic fuel injection fuse
2. Electronic fuel injection spare fuse
1. Headlight fuse
2. Signaling system fuse
3. Ignition fuse
4. Windshield motor fuse
5. Radiator fan fuse
6. Odometer, clock and immobilizer system fuse
(backup fuse)
7. Spare fuse (× 5)
8. Hazard fuse
9. Anti-lock Brake System fuse
(For FJR1300A only)
10.Parking lighting fuse
E_5jw_Periodic.fm Page 32 Monday, November 11, 2002 10:00 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-33
6
EC000103
CAUTION:_ Do not use a fuse of a higher amper-
age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire. _3. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
4. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
EAU04586
Replacing a headlight bulb This motorcycle is equipped with
quartz bulb headlights. If a headlight
bulb burns out, replace it as follows.
1. Remove panel B (if replacing the
left headlight bulb) or panel C (if
replacing the right headlight bulb).
(See page 6-6 for panel removal
and installation procedures.)
2. Disconnect the headlight coupler,
and then remove the headlight
bulb cover.
1. Main fuseSpecified fuses:
Main fuse: 50 A
Headlight fuse: 25 A
Signaling system fuse: 15 A
Ignition fuse: 10 A
Windshield motor fuse: 2 A
Radiator fan fuse: 15 A
Odometer, clock and
immobilizer system fuse
(backup fuse): 10 A
Hazard fuse: 7.5 A
Parking lighting fuse: 10 A
Electronic fuel injection
fuse: 15 A
Anti-lock Brake System
fuse
(For FJR1300A only): 7.5 A
1. Headlight coupler
2. Headlight bulb cover
E_5jw_Periodic.fm Page 33 Monday, November 11, 2002 10:00 AM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-36
6
EAU05019
Replacing a rear turn signal
light bulb or a tail/brake light
bulb 1. Remove the passenger seat. (See
page 3-17 for passenger seat re-
moval and installation proce-
dures.)
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
3. Remove the defective bulb by
turning it counterclockwise.4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the socket (together with
the bulb) by turning it clockwise.
6. Install the passenger seat.
EAU03087
Troubleshooting Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
1. Turn signal light bulb socket
2. Tail/brake light bulb socket
U5JWE2.book Page 36 Wednesday, November 6, 2002 3:32 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-37
6
EAU02990
Troubleshooting charts Starting problems or poor engine performance
EW000125
WARNING
_ Keep away open flames and do not smoke while checking or working on the fuel system. _
Check the fuel level in
the fuel tank.1. Fuel
There is enough fuel.
There is no fuel.
Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
Operate the electric starter.2. Compression
There is compression.
There is no compression.
Check the ignition.
Have a Yamaha dealer
check the vehicle.
Remove the spark plugs
and check the electrodes.3. Ignition
Wipe off with a dry cloth and correct the
spark plug gaps, or replace the spark plugs.
Have a Yamaha dealer check the vehicle.
The engine does not start.
Have a Yamaha dealer
check the vehicle.
The engine does not start.
Check the battery.
Operate the electric starter.4. Battery
The engine turns over
quickly.
The engine turns over
slowly.
The battery is good.Check the battery lead connections,
and charge the battery if necessary.
DryWet
Open the throttle halfway and operate
the electric starter.
U5JWE2.book Page 37 Wednesday, November 6, 2002 3:32 PM

MOTORCYCLE CARE AND STORAGE
7-2
7


Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.


Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.


For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quali-
ty plastic polishing compound
after washing.
_After normal useRemove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.After riding in the rain, near the sea or
on salt-sprayed roadsSince sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:_ Salt sprayed on roads in the winter may
remain well into spring. _1. Clean the motorcycle with cold
water and a mild detergent, after
the engine has cooled down.
ECA00012
CAUTION:_ Do not use warm water since it in-
creases the corrosive action of the
salt. _2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick-
el-plated, surfaces to prevent cor-
rosion.
U5JWE2.book Page 2 Wednesday, November 6, 2002 3:32 PM

MOTORCYCLE CARE AND STORAGE
7-4
7
Storage Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.
ECA00014
CAUTION:_

Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.


To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
_
Long-term
Before storing your motorcycle for
several months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.a. Remove the spark plug caps
and spark plugs.
b. Pour a teaspoonful of engine
oil into each spark plug bore.
c. Install the spark plug caps onto
the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder walls with oil.)
e. Remove the spark plug caps
from the spark plugs, and then
install the spark plugs and the
spark plug caps.
EWA00003
WARNING
_ To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over. _
U5JWE2.book Page 4 Wednesday, November 6, 2002 3:32 PM

8-1
8
EAU01038
8-SPECIFICATIONSSpecifications CS-01E
Model FJR1300/FJR1300A
Dimensions
Overall length 2,195 mm
Overall width 760 mm
Overall height 1,435 mm
Seat height 805 mm
Wheelbase 1,515 mm
Ground clearance 135 mm
Minimum turning radius 3,100 mm
Basic weight (with oil and full
fuel tank)
FJR1300 275 kg
FJR1300A 282 kg
Engine
Engine type Liquid-cooled 4-stroke, DOHC
Cylinder arrangement Forward-inclined parallel
4-cylinder
Displacement 1,298 cm
3
Bore × stroke 79.0 × 66.2 mm
Compression ratio 10.8:1
Starting system Electric starter
Lubrication system Wet sumpEngine oil
Ty p e
Recommended engine oil
classification API Service SE, SF, SG or
higher
Quantity
Without oil filter cartridge
replacement 3.8 L
With oil filter car tridge
replacement 4 L
Total amount (dry engine) 4.9 L
-20 -10 0
10 20 30
40
50 ˚C
SAE 15W-40SAE 20W-40SAE 10W-40
CAUTION:In order to prevent clutch slippage (since the engine oil also
lubricates the clutch), do not mix any chemical additives. Do
not use oils with a diesel specification of “CD” or oils of a
higher quality than specified. In addition, do not use oils la-
beled “ENERGY CONSERVING II” or higher.
U5JWE2.book Page 1 Wednesday, November 6, 2002 3:32 PM

SPECIFICATIONS
8-2
8
Final gear oil
Type Shaft drive gear oil
(Part No.: 9079E-SH001-00)
Quantity 0.2 L
Cooling system capacity
(total amount)
3.3 L
Air filterDry element
Fuel
Type REGULAR UNLEADED
GASOLINE ONLY
Fuel tank capacity 25 L
Fuel reserve amount 5 L
Electronic Fuel Injection system
Model INP-732/4
Manufacturer NIPPON INJECTOR
Spark plug
Manufacturer/model NGK / CR8E or
DENSO / U24ESR-N
Gap 0.7–0.8 mm
Clutch typeWet, multiple-disc
Transmission
Primary reduction system Helical gear
Primary reduction ratio 1.563
Secondary reduction system Shaft drive
Secondary reduction ratio 2.773Transmission type Constant-mesh 5-speed
Operation Left foot
Gear ratio
1st 2.529
2nd 1.773
3rd 1.348
4th 1.077
5th 0.929
Chassis
Frame type Diamond
Caster angle 26°
Trail 109 mm
Tires
Front
Type Tubeless tire
Size 120/70 ZR17 M/C (58 W)
Manufacturer/model Metzeler / MEZ4J FRONT
Bridgestone / BT020FN
Rear
Type Tubeless tire
Size 180/55 ZR17 M/C (73 W)
Manufacturer/model Metzeler / MEZ4J
Bridgestone / BT020RN
U5JWE2.book Page 2 Wednesday, November 6, 2002 3:32 PM