air filter YAMAHA FX HO 2006 Owners Manual

2-4
E
1Air filter case
2Water separator
3Fuel tank
4Battery
5Flush hose connector
Use to flush the engine cooling water pas-
sages.
6Electrical box
Protects electrical components from water.
7Oil tank8Muffler
9Spark plugs/Spark plug caps/Ignition coils
E_F1X-70.book Page 4 Friday, August 26, 2005 11:00 AM

3-7
E
EJU20831
Engine oil level
Check the engine oil level before each
use.
CAUTION:@
When checking the engine oil level on
water, be careful of other watercraft,
boats, swimmers, and obstacles. The
water current and wind can cause the
watercraft to move and lead to a colli-
sion.

When checking the engine oil level on
land, supply water to the cooling water
passages. (See page 4-1 for proce-
dures on supplying water.)

Make sure that the engine has enough
oil but do not overfill it. If there is too
little oil, the engine can be damaged. If
there is too much oil, the air filter can
become saturated with oil, perma-
nently damaging the filter and reduc-
ing engine performance. Follow the
checking procedure carefully.

Make sure that debris and water do not
enter the oil tank filler hole. Debris and
water in the engine oil can cause seri-
ous engine damage.
@
Checking the engine oil level:
1. Place the watercraft in a horizontal posi-
tion or launch the watercraft, and then
start the engine.
2. Run the engine at trolling speed for
6 minutes or more, and then stop the
engine.
NOTE:@ If the ambient temperature is 20 °C (68 °F)
or less, warm up the engine for an additional
5 minutes.
@
3. Remove the rear and front seats. (See
pages 2-5 and 2-6 for seat removal and
installation procedures.)
E_F1X-70.book Page 7 Friday, August 26, 2005 11:00 AM

3-29
E
EJU18102
Capsized watercraft
If the watercraft capsizes, turn it over
immediately.
Be sure to carefully follow the procedures
below to prevent injury or damage to the
watercraft.
WARNING@ IMPROPER UPRIGHTING CAN CAUSE
INJURY:

Make sure that the engine shut-off
cord is removed from the engine shut-
off switch.

Do not put your hands in the intake
grate.

Watch so you are not hit by the water-
craft as it comes over.
@
CAUTION:@ If the watercraft capsizes, release the
throttle lever immediately. Oil could flow
into the air filter case and the engine
could be damaged.
@
1. Remove the clip from the engine shut-off
switch.
2. Swim to the rear of the watercraft. Pull
the watercraft over with your left hand on
the ride plate while pushing down on the
gunwale with your right hand or foot.
NOTE:@ If the port (left) side of the capsized water-
craft is tilting up, push down on the gunwale
so that the port (left) side is down before
turning the watercraft clockwise.
@
CAUTION:@ Do not turn the watercraft over counter-
clockwise, otherwise water can leak into
the engine, which can result in severe
damage.
@
E_F1X-70.book Page 29 Friday, August 26, 2005 11:00 AM

E
4
EJU10860
MAINTENANCE AND
CARE
Storage ...................................................... 4-1
Flushing the cooling system .................. 4-1
Lubrication .............................................. 4-3
Fuel system ............................................ 4-4
Battery .................................................... 4-5
Cleaning the watercraft .......................... 4-6
Maintenance and adjustments .............. 4-7
Owner’s/Operator’s Manual and
tool kit ..................................................... 4-9
Periodic maintenance chart ................. 4-10
Inspecting the fuel system ................... 4-11
Changing the engine oil ....................... 4-12
Checking the air filter element ............. 4-14
Inspecting the jet thrust
nozzle angle ......................................... 4-15
Inspecting the shift cable ..................... 4-15
Inspecting and adjusting the
throttle cable ......................................... 4-15
Cleaning and adjusting the
spark plugs ........................................... 4-16
Lubrication points ................................. 4-18
Inspecting the battery .......................... 4-21
Adjusting the fuel injection system ...... 4-23
Replacing the fuse ............................... 4-24
Specifications ........................................ 4-25
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM

4-3
E
EJU18980
Lubrication
WARNING@ Do not spray flammable rust inhibitor
products on engine surfaces while the
engine is hot. The sprayed substance or
propellants could catch fire.
@
1. Remove the rear and front seats. (See
pages 2-5 to 2-6 for seat removal and
installation procedures.)
2. Remove the air filter case cover
screws1, slide the locks 2 open, and
then remove the case cover.
3. Remove the air filter case cover and air
filter element.
4. Spray a rust inhibitor into each intake
opening 3 for 3 seconds.
5. Install the air filter element and air filter
case cover.
6. Start the engine in a well-ventilated area
and let it run at idle for 15 seconds.
CAUTION:@ Do not run the engine for more than
15 seconds. The engine could overheat.
@
7. Lubricate all cables such as the throttle
and steering cables.
NOTE:@ Use a suitable marine grease applicator to
pressure lubricate the cables and purge out
any moisture between the inner and outer
cables.
@
8. Lubricate the areas of the watercraft
specified under Lubrication points on
page 4-18.
E_F1X-70.book Page 3 Friday, August 26, 2005 11:00 AM

4-10
E
EJU13550
Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, depend-
ing on your operating conditions maintenance may need to be performed more frequently.
PMC-F1B1(
) This mark indicates maintenance that you may do yourself.
(
❍) This mark indicates work to be done by a Yamaha dealer.
MAINTENANCE INTERVAL
INITIALTHEREAFTER
EVERYPA G E
10
hours50
hours100
hours100
hours200
hours
ITEM
6
months12
months12
months24
months
Spark plug Inspect, clean, adjust



4-16
Lubrication points Lubricate

/❍

/❍
4-18
Intermediate housing Lubricate❍
*1

*2

*2 4-20
Fuel system Inspect❍❍
4-11
Fuel tank Inspect, clean❍❍
4-11
Trolling speed Inspect, adjust❍❍
4-23
Throttle shaft Inspect❍❍
—
Cooling water passages Flush

*3 4-1
Water inlet strainer Inspect, clean❍❍
—
Bilge strainer Clean❍❍
—
Electric bilge pump strainer Inspect, clean❍❍
—
Impeller Inspect❍❍
—
Jet thrust nozzle angle Inspect, adjust

/❍

/❍
4-15
Steering master Inspect❍❍❍
—
QSTS mechanism Inspect, adjust❍❍❍
—
Shift cable and mechanism Inspect, adjust❍❍
4-15
Throttle cable Inspect, adjust❍❍❍
4-15
Stern drain plugs Inspect, replace❍❍
3-10
Battery Inspect ❍❍
—
Rubber coupling Inspect❍
—
Engine mount Inspect❍
—
Nuts and bolts Inspect❍❍❍
—
Air filter Inspect, replace


4-14
Engine oil Replace❍❍❍
4-12
Engine oil filter Replace❍❍
—
Valve clearance Inspect, adjust❍
—
*1: Grease quantity: 33.0–35.0 cm3 (1.11–1.18 oz)
*2: Grease quantity: 6.0–8.0 cm3 (0.20–0.27 oz)
*3: After every use
E_F1X-70-4.fm Page 10 Monday, August 29, 2005 1:36 PM

4-14
E
EJU18190
Checking the air filter element
The air filter element should be checked
every 12 months or every 100 hours of oper-
ation.
To check the air filter:
1. Remove the rear and front seats. (See
pages 2-5 and 2-6 for seat removal and
installation procedures.)
2. Remove the air filter case cover
screws1, slide the locks 2 open, and
then remove the case cover.
3. Remove the air filter element and check
it for dirt and oil. Replace the air filter ele-
ment if there is any oil buildup, or every
2 years or every 200 hours of operation.
4. Install the air filter element in the air filter
case, and then install the case cover.
CAUTION:@
Make sure that the air filter element is
installed in the filter case properly.

Do not start the engine with the air fil-
ter element removed, otherwise the
pistons and cylinders could be dam-
aged.

If cleaning the air filter element, use
cold or lukewarm water and let it air
dry completely. Do not use detergent
or solvent to clean the air filter ele-
ment, or dry it with heat or com-
pressed air, otherwise it could be
damaged.
@
E_F1X-70.book Page 14 Friday, August 26, 2005 11:00 AM

4-16
E
EJU21070
Cleaning and adjusting the
spark plugs
The spark plug is an important engine
component and is easy to inspect. The con-
dition of the spark plug can indicate some-
thing about the condition of the engine. For
example, if one spark plug shows a distinctly
different color, the engine could be defec-
tive. Do not attempt to diagnose any prob-
lems yourself. Have a Yamaha dealer
service the watercraft.
Remove and inspect the spark plugs peri-
odically; heat and deposits will cause the
spark plugs to slowly break down and erode.
If electrode erosion becomes excessive, or if
carbon and other deposits are excessive,
replace the spark plug with the specified
plug.
Removing a spark plug:
1. Remove the air filter case cover and air
filter element. (See page 4-14 for air filter
removal and installation procedures.)
2. Remove the spark plug cap.
CAUTION:@ Do not use any tools to remove or install
the spark plug cap, otherwise the igni-
tion coil coupler may get damaged. The
spark plug cap may be difficult to remove
because the rubber seal on the end of
the cap fits tightly. To remove the spark
plug cap, simply twist it back and forth
while pulling it up; to install it, twist it
back and forth while pushing it down.
@
3. Remove the spark plug.
Specified spark plug: NGK CR9EB
E_F1X-70.book Page 16 Friday, August 26, 2005 11:00 AM

4-17
E
Measure the spark plug gap a with a
wire thickness gauge. Replace the spark
plug or adjust the gap to specification if nec-
essary.
To install the spark plug:
1. Clean the gasket surface.
2. Wipe any dirt from the threads of the
spark plug.
3. Install the spark plug, and then tighten it
to the specified torque.
4. Install the spark plug cap.
NOTE:@
Wipe off any water on the spark plug or
inside the cap before installing the spark
plug cap. Push the spark plug cap down
until it is securely installed.

If a torque wrench is not available when
you are installing a new spark plug, a good
estimate of the correct torque is 1/4 turn to
1/2 turn past finger tight with the spark
plug wrench included in the tool kit. Have
the spark plug adjusted to the correct
torque with a torque wrench as soon as
possible.
@
WARNING@ Be careful not to damage the insulator
when removing or installing a spark plug.
A damaged insulator could allow sparks
to escape, which could lead to an explo-
sion or fire.
@
5. Install the air filter element in the air filter
case, and then install the air filter case
cover. Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Spark plug tightening torque:
12.5 N·m (1.25 kgf·m, 9 ft·lb)
E_F1X-70.book Page 17 Friday, August 26, 2005 11:00 AM

5-2
E
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as possi-
ble3-4
Stale or contaminated Have serviced by
Yamaha dealer4-11
Fuel tank Water or dirt present Have serviced by
Yamaha dealer4-11
Spark plug Fouled or defective Replace 4-16
Incorrect heat range Replace 4-16
Gap incorrect Adjust 4-16
Spark plug cap Loose Connect properly 4-16
Cracked, torn, or dam-
agedReplace
—
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel injection
systemJet nozzle clogged Have serviced by
Yamaha dealer—
Warning light or
indicator blinksFuel level Empty Refill as soon as possi-
ble3-4
Engine over-
heatedJet intake clogged Clean
5-3
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer—
Wate rcr af t slow or
loses powerYamaha
Security
SystemLow-RPM mode
selectedSelect normal mode
2-22
Cavitation Jet intake clogged Clean 5-3
Impeller damaged or
wornHave serviced by
Yamaha dealer—
Engine over-
heat warningEngine speed reduc-
tion control activatedClean jet intake and
cool engine2-30
Oil pressure
warningEngine speed reduc-
tion control activatedAdd oil
2-30
Spark plug Fouled or defective Replace 4-16
Incorrect heat range Replace 4-16
Gap incorrect Adjust 4-16
Spark plug
capsLoose Connect properly
4-16
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel Stale or contaminated Have serviced by
Yamaha dealer4-11
Air filter Clogged Clean or replace 4-14
Oil buildup Replace 4-14 TROUBLE POSSIBLE CAUSE REMEDY PAGE
E_F1X-70.book Page 2 Friday, August 26, 2005 11:00 AM