check engine light YAMAHA FX HO 2006 Owners Manual

2-23
E
CAUTION:@ If the remote control transmitter does not
operate when its buttons are pressed,
the battery may be low. Have a Yamaha
dealer replace the battery.
@
EJU22240
Multifunction meter
The multifunction meter is equipped with
the following three main components for
help and convenience in operating the
watercraft.
1
Analog speedometer/tachometer and indicator
lights
2
Left multifunction display and operation but-
tons
3
Right multifunction display and operation but-
tons (for FX Cruiser High Output)
CAUTION:@ Do not run the engine for more than 15
seconds when checking the operation of
the meter on land. The engine could
overheat.
@
NOTE:@
When the multifunction meter starts oper-
ating, the analog speedometer/tachome-
ter makes one sweep, all displays light up
for 2 seconds, and then the meter starts
to operate normally.

The multifunction meter will continue to
operate for 25 seconds after the engine
stops.
@
E_F1X-70.book Page 23 Friday, August 26, 2005 11:00 AM

2-27
E
EJU22040
Left multifunction display and
operation buttons
The left multifunction display is equipped
with the following functions.
1
Digital speedometer
2
Fuel meter
3
Hour meter/Voltmeter
4
Check engine warning indicator
5
Fuel warning indicator
6
Oil pressure warning indicator
7
Engine overheat warning indicator
The following operation buttons are on the
left side of the multifunction meter.
8
“Volt/Hour” button
9
“Speed/RPM” button
EJU22270
Digital speedometer
The digital speedometer 1
shows the
watercraft speed against water.
NOTE:@
To switch the speedometer display
between kilometers and miles, push the
“Vo l t / H o u r” button 2
for at least 1 second,
within 10 seconds after the multifunction
meter starts operating.

The “SPEED” indicator light 3
blinks
three times if miles are selected as the
display units when the multifunction meter
starts operating, or if the display units of
the meter are switched to miles.
@
E_F1X-70.book Page 27 Friday, August 26, 2005 11:00 AM

2-29
E
EJU22060
Check engine warning indicator
If a sensor malfunction or a short circuit is
detected, the “WARNING” indicator light and
the check engine warning indicator begin to
blink and the buzzer sounds intermittently.
If this occurs, reduce the engine speed,
return to shore, and have a Yamaha dealer
check the engine.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22070
Fuel warning indicator
If the fuel remaining in the tank drops to
about 13 L (3.4 US gal, 2.9 Imp gal), the
lowest two fuel level segments, the fuel
warning indicator, and the “WARNING” indi-
cator light all begin to blink. The buzzer also
starts sounding intermittently.
The warning signals will be cleared when
the engine is restarted after refilling.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
E_F1X-70.book Page 29 Friday, August 26, 2005 11:00 AM

2-30
E
EJU22080
Oil pressure warning indicator
If the oil pressure does not rise to specifi-
cation, the “WARNING” indicator light and
the oil pressure warning indicator begin to
blink and the buzzer sounds intermittently.
At the same time, the engine speed is lim-
ited to help prevent damage.
If this occurs, reduce the engine speed,
return to shore, and then check the engine
oil level. (See page 3-7 for engine oil level
checking procedures.) If the oil level is low,
add enough engine oil to raise it to the
proper level. If the oil level is sufficient, have
a Yamaha dealer check the watercraft.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22090
Engine overheat warning indicator
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the
“WARNING” indicator light and the overheat
warning indicator blink, and then come on.
The buzzer also begins to sound intermit-
tently, and then it sounds continuously. After
the light and indicator start to blink and the
buzzer sounds, the engine speed is limited
to help prevent damage.
If this occurs, immediately reduce the
engine speed, return to shore, and then
check for water discharge at the port (left)
cooling water pilot outlet. If there is no dis-
charge of water, check the intake grate and
impeller for clogging.
E_F1X-70.book Page 30 Friday, August 26, 2005 11:00 AM

3-22
E
EJU10680
Operating your watercraft
EJU12500
Getting to know your
watercraft
Operating your watercraft requires skills
acquired through practice over a period of
time. Take the time to learn the basic tech-
niques well before attempting more difficult
maneuvers.
Operating your new watercraft can be a
very enjoyable activity, providing you with
hours of pleasure. However, it is essential to
familiarize yourself with the operation of the
watercraft to achieve the skill level neces-
sary to enjoy riding safely. Before operating
this watercraft, read this Owner’s/Operator’s
Manual, the Riding Practice Guide, and all
warning and caution labels on the water-
craft. Pay particular attention to the safety
information on pages 1-13 to 1-20. These
materials should give you an understanding
of the watercraft and its operation.
Remember: This watercraft is designed to
carry the operator and up to 2 passengers.
Never exceed the maximum load limit or
allow more than 3 persons (or 2 persons if a
water-skier is being pulled) to ride the water-
craft at one time.
EJU10700
Learning to operate your
watercraft
Before operating the watercraft, always
perform the pre-operation checks listed on
page 3-5. The short time spent checking the
watercraft will reward you with added safety
and reliability.
Check all local laws before operating your
watercraft.
Operate defensively at safe speeds and
keep a safe distance away from people,
objects, and other watercraft. Select a wide
area to learn in, where you have good visi-
bility and light boat traffic.
Use the buddy system—operate with
someone nearby. Scan constantly for peo-
ple, objects, and other watercraft. Be alert
for conditions that limit your visibility or block
your vision of others.
Attach the engine shut-off cord (lanyard)
to your wrist and keep it free from the han-
dlebars so that the engine stops if the opera-
tor falls off.
Wear a personal flotation device (PFD).
All riders must wear an authority-approved
PFD that is suitable for personal watercraft
use. Maximum load: 240 kg (530 lb)
Load is the total weight of cargo,
operator and passengers.
E_F1X-70.book Page 22 Friday, August 26, 2005 11:00 AM

5-2
E
Engine runs irregu-
larly or stallsFuel Empty Refill as soon as possi-
ble3-4
Stale or contaminated Have serviced by
Yamaha dealer4-11
Fuel tank Water or dirt present Have serviced by
Yamaha dealer4-11
Spark plug Fouled or defective Replace 4-16
Incorrect heat range Replace 4-16
Gap incorrect Adjust 4-16
Spark plug cap Loose Connect properly 4-16
Cracked, torn, or dam-
agedReplace
—
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel injection
systemJet nozzle clogged Have serviced by
Yamaha dealer—
Warning light or
indicator blinksFuel level Empty Refill as soon as possi-
ble3-4
Engine over-
heatedJet intake clogged Clean
5-3
Check engine
warningFaulty sensors Have serviced by
Yamaha dealer—
Wate rcr af t slow or
loses powerYamaha
Security
SystemLow-RPM mode
selectedSelect normal mode
2-22
Cavitation Jet intake clogged Clean 5-3
Impeller damaged or
wornHave serviced by
Yamaha dealer—
Engine over-
heat warningEngine speed reduc-
tion control activatedClean jet intake and
cool engine2-30
Oil pressure
warningEngine speed reduc-
tion control activatedAdd oil
2-30
Spark plug Fouled or defective Replace 4-16
Incorrect heat range Replace 4-16
Gap incorrect Adjust 4-16
Spark plug
capsLoose Connect properly
4-16
Electrical wir-
ingLoose connection Tighten or connect
properly—
Fuel Stale or contaminated Have serviced by
Yamaha dealer4-11
Air filter Clogged Clean or replace 4-14
Oil buildup Replace 4-14 TROUBLE POSSIBLE CAUSE REMEDY PAGE
E_F1X-70.book Page 2 Friday, August 26, 2005 11:00 AM

6-1
E
EJU11250
Index
A
Adjusting the fuel injection system ........ 4-23
Analog speedometer/tachometer .......... 2-24
Analog speedometer/tachometer and
indicator lights ....................................... 2-24
Approval label of Emission control
certificate ................................................. 1-4
B
Battery ............................................ 3-10, 4-5
Beaching the watercraft ........................ 3-34
Beverage holder .................................... 2-38
Bilge ........................................................ 3-9
Boarding alone ...................................... 3-26
Boarding and starting in deep water ..... 3-26
Boarding with passengers ..................... 3-27
Bow down.............................................. 2-17
Bow up .................................................. 2-17
Builder’s plate.......................................... 1-3
C
Capsized watercraft .............................. 3-29
Changing the engine oil ........................ 4-12
Check engine warning indicator ............ 2-29
Checking the air filter element............... 4-14
Checking the trolling speed ................... 4-23
Cleaning and adjusting the
spark plugs ............................................ 4-16
Cleaning the jet intake and impeller ........ 5-3
Cleaning the watercraft ........................... 4-6
Connecting the jumper cables................. 5-6
Cooling water pilot outlet .............. 2-12, 3-16
Cruising limitations ................................ 1-14
D
Digital speedometer .............................. 2-27
Docking the watercraft .......................... 3-34
E
Emergency procedures ........................... 5-3
Emission control information
(For Canada only) ................................... 1-4
Engine break-in ..................................... 3-17
Engine compartment ............................... 3-6Engine oil ................................................ 3-3
Engine oil level ........................................ 3-7
Engine overheat warning indicator ........ 2-30
Engine serial number .............................. 1-2
Engine shut-off cord (lanyard) ............... 3-15
Engine shut-off switch ........................... 2-10
Engine stop switch ................................ 2-10
Enjoy your watercraft responsibly ......... 1-21
F
Filling the fuel tank .................................. 3-4
Fire extinguisher .................................... 3-11
Flushing the cooling system .................... 4-1
Front seat ................................................ 2-6
Front storage compartment ................... 2-36
Fuel and oil.............................................. 3-1
Fuel level ................................................. 3-6
Fuel meter ............................................. 2-28
Fuel system ............................................. 4-4
Fuel tank ............................................... 4-11
Fuel tank filler cap ................................... 2-7
Fuel warning indicator ........................... 2-29
G
Gasohol ................................................... 3-2
Gasoline .................................................. 3-1
Getting to know your watercraft ............ 3-22
Glove compartment ............................... 2-37
H
Handgrip ................................................ 2-18
Hazard information ................................ 1-18
Hood........................................................ 2-7
Hour meter/Voltmeter ............................ 2-28
Hull and deck .......................................... 3-6
Hull Identification Number (HIN).............. 1-2
I
Identification numbers ............................. 1-1
Important labels ....................................... 1-5
Inspecting and adjusting the
throttle cable.......................................... 4-15
Inspecting the battery ............................ 4-21
Inspecting the fuel system ..................... 4-11
Inspecting the jet thrust nozzle angle .... 4-15
Inspecting the shift cable ....................... 4-15
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM

6-2
E
J
Jet unit................................................... 3-15
Jumping the battery................................. 5-5
L
Label location .......................................... 1-5
Launching the watercraft ....................... 3-18
Learning to operate your watercraft ...... 3-22
Leaving the watercraft ........................... 3-21
Left multifunction display and
operation buttons .................................. 2-27
Limitations on who may operate the
watercraft .............................................. 1-13
“L-MODE” indicator light........................ 2-26
Location of main components ................. 2-1
Lubrication............................................... 4-3
Lubrication points .................................. 4-18
M
Maintenance and adjustments ................ 4-7
Manufactured date label.......................... 1-4
Model information.................................... 1-3
Multifunction meter ....................... 2-23, 3-16
O
Oil pressure warning indicator............... 2-30
Operating your watercraft...................... 3-22
Operation .............................................. 3-17
Operation of controls and other
functions .................................................. 2-5
Operation requirements ........................ 1-15
Other labels ........................................... 1-11
Owner’s/Operator’s Manual and
tool kit ...................................................... 4-9
P
Periodic maintenance chart................... 4-10
Post-operation checks........................... 3-36
Pre-operation check list........................... 3-5
Pre-operation check points ..................... 3-6
Pre-operation checks .............................. 3-5
Primary Identification (PRI-ID) number ... 1-1
Pull-up cleats
(for FX Cruiser High Output) ................. 2-19
Q
Quick Shift Trim System (QSTS) .......... 3-14Quick Shift Trim System (QSTS)
selector.................................................. 2-16
R
Rear seat................................................. 2-5
Reboarding step
(for FX Cruiser High Output) ................. 2-18
Recommended equipment .................... 1-17
Remote control transmitter ...................... 2-8
Replacing the fuse ................................ 4-24
Reverse on waterways .......................... 3-35
Riding watercraft with passengers ........ 3-23
Right multifunction display and
operation buttons
(for FX Cruiser High Output) ................. 2-31
Rough water operation .......................... 3-35
“RPM” indicator light.............................. 2-26
S
Safe boating rules ................................. 1-21
Safety information ................................. 1-13
Seat storage compartment .................... 2-37
Selecting the normal mode/
low-RPM mode...................................... 2-22
Shift lever .............................................. 2-15
Shift lever and reverse gate .................. 3-13
Specifications ........................................ 4-25
“SPEED” indicator light ......................... 2-25
Starting and boarding in shallow
water ..................................................... 3-25
Starting from a dock .............................. 3-25
Starting the engine ................................ 3-19
Starting the watercraft ........................... 3-24
Start switch............................................ 2-11
Steering system ...........................2-13, 3-12
Stern drain plug ..................................... 3-10
Stopping the engine .............................. 3-21
Stopping the watercraft ......................... 3-33
Storage.................................................... 4-1
Storage compartments .......................... 2-36
Submerged watercraft ............................. 5-8
Switches ................................................ 3-16
T
Throttle .................................................. 3-12
Throttle lever ......................................... 2-11
E_F1X-70.book Page 2 Friday, August 26, 2005 11:00 AM