start stop button YAMAHA FX HO 2006 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2006, Model line: FX HO, Model: YAMAHA FX HO 2006Pages: 152, PDF Size: 11.96 MB
Page 29 of 152
E
2
EJU10070
FEATURES AND
FUNCTIONS
Location of main components .............. 2-1
Operation of controls and other
functions ................................................... 2-5
Rear seat ................................................ 2-5
Front seat ............................................... 2-6
Hood ....................................................... 2-7
Fuel tank filler cap .................................. 2-7
Remote control transmitter .................... 2-8
Engine stop switch ............................... 2-10
Engine shut-off switch .......................... 2-10
Start switch ........................................... 2-11
Throttle lever ........................................ 2-11
Cooling water pilot outlet ..................... 2-12
Steering system ................................... 2-13
Tilt lever ................................................ 2-14
Shift lever .............................................. 2-15
Quick Shift Trim System (QSTS)
selector ................................................. 2-16
Handgrip ............................................... 2-18
Reboarding step
(for FX Cruiser High Output) ............... 2-18
Pull-up cleats
(for FX Cruiser High Output) ............... 2-19
Yamaha Engine Management System
(YEMS) ................................................. 2-20
Yamaha Security System/Low-RPM
mode .................................................... 2-20
Multifunction meter ............................... 2-23
Analog speedometer/tachometer and
indicator lights ...................................... 2-24
Left multifunction display and
operation buttons ................................. 2-27
Right multifunction display and
operation buttons
(for FX Cruiser High Output) ............... 2-31
Storage compartments ........................ 2-36
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM
Page 39 of 152
2-10
E
EJU10150
Engine stop switch
Push this switch 1 (red button) to stop
the engine normally.
EJU10160
Engine shut-off switch
Insert the clip 1, on the end of the engine
shut-off cord 2, under the engine shut-off
switch 3 (black button). The engine will stop
automatically when the clip is removed from
the switch, such as if the operator falls off
the watercraft.
WARNING@ Always attach the engine shut-off cord
to your wrist and the clip to the engine
shut-off switch BEFORE starting the
engine.
To prevent accidental starting of the
engine or unauthorized use by chil-
dren or others, always remove the clip
from the shut-off switch when the
engine is not running.
@
E_F1X-70.book Page 10 Friday, August 26, 2005 11:00 AM
Page 50 of 152
2-21
E
EJU21780
Yamaha Security System lock and
unlock modes
The lock and unlock modes of this system
can only be selected while the engine is
stopped.
When the lock button 1 is pressed, the
beeper sounds once. This indicates the lock
mode is selected and the engine cannot be
started.
The “UNLOCK” indicator light 2 comes
on when the security system is in the unlock
mode and goes off when the security sys-
tem is in the lock mode.
When the unlock button 3 is pressed for
a short time, the beeper sounds two times
for the normal mode or three times for the
low-RPM mode. The “UNLOCK” indicator
light will come on and the engine can be
started. (See the items in “Selecting the nor-
mal mode/low-RPM mode” for operation
mode information.)
Number of
beepsYamaha Security
System modeEngine can
be started
1 beep Lock NO
2 beepsUnlock
(normal mode)YES
3 beepsUnlock
(low-RPM mode)YES
E_F1X-70.book Page 21 Friday, August 26, 2005 11:00 AM
Page 51 of 152
2-22
E
EJU21583
Selecting the normal mode/low-
RPM mode
The normal mode and low-RPM mode
can only be selected when the engine is
stopped in the unlock mode. Press the
unlock button for more than 4 seconds to
select the normal mode or low-RPM mode.
Normal mode
If the beeper sounds twice, the normal
mode is activated.
The watercraft can be ridden normally.
Low-RPM mode
If the beeper sounds three times, the low-
RPM mode is activated and the “L-MODE”
indicator light 1 comes on.
Maximum engine speed (r/min) in the low-
RPM mode is limited to approximately 80%
of the maximum engine speed in the normal
mode.
NOTE:@ If neither the start switch nor the remote
control transmitter is operated within
25 seconds after the unlock button is
pressed to select the unlock mode, the
multifunction meter display and the
“L-MODE” indicator light will go off. If this
occurs, press the lock button briefly to
select the lock mode, press the unlock
button briefly to select the unlock mode,
and then press the unlock button again for
more than 4 seconds to select the normal
mode or low-RPM mode.
While the engine is running, input from
the remote control transmitter is not
received.
@
E_F1X-70-2.fm Page 22 Tuesday, January 31, 2006 9:53 AM
Page 52 of 152
2-23
E
CAUTION:@ If the remote control transmitter does not
operate when its buttons are pressed,
the battery may be low. Have a Yamaha
dealer replace the battery.
@
EJU22240
Multifunction meter
The multifunction meter is equipped with
the following three main components for
help and convenience in operating the
watercraft.
1
Analog speedometer/tachometer and indicator
lights
2
Left multifunction display and operation but-
tons
3
Right multifunction display and operation but-
tons (for FX Cruiser High Output)
CAUTION:@ Do not run the engine for more than 15
seconds when checking the operation of
the meter on land. The engine could
overheat.
@
NOTE:@ When the multifunction meter starts oper-
ating, the analog speedometer/tachome-
ter makes one sweep, all displays light up
for 2 seconds, and then the meter starts
to operate normally.
The multifunction meter will continue to
operate for 25 seconds after the engine
stops.
@
E_F1X-70.book Page 23 Friday, August 26, 2005 11:00 AM
Page 58 of 152
2-29
E
EJU22060
Check engine warning indicator
If a sensor malfunction or a short circuit is
detected, the “WARNING” indicator light and
the check engine warning indicator begin to
blink and the buzzer sounds intermittently.
If this occurs, reduce the engine speed,
return to shore, and have a Yamaha dealer
check the engine.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22070
Fuel warning indicator
If the fuel remaining in the tank drops to
about 13 L (3.4 US gal, 2.9 Imp gal), the
lowest two fuel level segments, the fuel
warning indicator, and the “WARNING” indi-
cator light all begin to blink. The buzzer also
starts sounding intermittently.
The warning signals will be cleared when
the engine is restarted after refilling.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
E_F1X-70.book Page 29 Friday, August 26, 2005 11:00 AM
Page 59 of 152
2-30
E
EJU22080
Oil pressure warning indicator
If the oil pressure does not rise to specifi-
cation, the “WARNING” indicator light and
the oil pressure warning indicator begin to
blink and the buzzer sounds intermittently.
At the same time, the engine speed is lim-
ited to help prevent damage.
If this occurs, reduce the engine speed,
return to shore, and then check the engine
oil level. (See page 3-7 for engine oil level
checking procedures.) If the oil level is low,
add enough engine oil to raise it to the
proper level. If the oil level is sufficient, have
a Yamaha dealer check the watercraft.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22090
Engine overheat warning indicator
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the
“WARNING” indicator light and the overheat
warning indicator blink, and then come on.
The buzzer also begins to sound intermit-
tently, and then it sounds continuously. After
the light and indicator start to blink and the
buzzer sounds, the engine speed is limited
to help prevent damage.
If this occurs, immediately reduce the
engine speed, return to shore, and then
check for water discharge at the port (left)
cooling water pilot outlet. If there is no dis-
charge of water, check the intake grate and
impeller for clogging.
E_F1X-70.book Page 30 Friday, August 26, 2005 11:00 AM
Page 61 of 152
2-32
E
The following operation buttons are on the
right side of the multifunction meter.
1
“Mode/Reset” button
2
“Start/Stop” button
To switch the display mode, push the
“Mode/Reset” button 1
for less than 1 sec-
ond. The display mode changes in the fol-
lowing order.
Compass → Average speed → Tr i p m e t e r
→ Trip timer → Fuel consumption per hour
→ Fuel consumption per kilometer/mile →
Water temperature → Air temperature
NOTE:@ To switch the display units between kilo-
meters/liters/degrees Celsius and miles/
gallons/degrees Fahrenheit, push the
“Vo l t / H o u r” button 3
for at least 1 second,
within 10 seconds after the multifunction
meter starts operating.
The “SPEED” indicator light blinks three
times if miles/gallons/degrees Fahrenheit
are selected as the display units when the
multifunction meter starts operating, or if
the display units of the meter are switched
to miles/gallons/degrees Fahrenheit.
@
E_F1X-70.book Page 32 Friday, August 26, 2005 11:00 AM
Page 64 of 152
2-35
E
Average speed/Tripmeter/Trip timer
modes
Average speed, distance traveled, and
trip time are recorded once measurements
have started, regardless of the current dis-
play.
To start the measurements, push the
“Start/Stop” button 2 for less than 1 sec-
ond. The beeper sounds once.
To stop the measurements, push the
“Start/Stop” button for less than 1 second.
The beeper sounds once. To restart the
measurements, push the “Start/Stop” button
for less than 1 second. The beeper sounds
once.
To reset the displays, push the “Mode/
Reset” button 1 for at least 2 seconds while
the measurements are stopped. The beeper
sounds twice.
NOTE:@ The displays can be reset only when the
measurements are stopped.
@
E_F1X-70.book Page 35 Friday, August 26, 2005 11:00 AM
Page 89 of 152
3-20
E
3. Attach the clip 1 to the engine shut-off
switch 2 and attach the engine shut-off
cord 3 to your left wrist.
WARNING@ Check that the engine shut-off cord is not
frayed or broken, and keep it free from
the handlebars so the engine stops if the
operator falls off. The engine shut-off
cord may not pull free if wrapped around
the handlebars when the operator falls
off, allowing the watercraft to continue to
run and cause an accident.
@
NOTE:@ It is not possible to start the engine with the
clip removed from the engine shut-off
switch.
@
4. Push the start switch (green button), and
then release it as soon as the engine
starts to run.
NOTE:@ The engine will not start if the throttle lever is
squeezed.
@
CAUTION:@ Never push the start switch while the
engine is running.
Do not operate the start switch for
more than 5 seconds, otherwise the
battery will be discharged and the
engine will not start. Also, the starter
motor may be damaged. If the engine
does not start in 5 seconds, release
the start switch, wait 15 seconds, and
then try again.
@
E_F1X-70.book Page 20 Friday, August 26, 2005 11:00 AM