display YAMAHA FX HO 2010 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2010, Model line: FX HO, Model: YAMAHA FX HO 2010Pages: 110, PDF Size: 7.76 MB
Page 6 of 110
Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Craft Identification Number (CIN) ...... 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 8
Safety information ........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 12
Recommended equipment ........... 14
Hazard information ....................... 15
Watercraft characteristics ............. 15
Water-skiing ................................. 17
Safe boating rules ........................ 19
Enjoy your watercraft
responsibly ................................ 19
Description....................................... 21
Watercraft glossary ...................... 21
Location of main components ...... 22
Control function operation ............. 26
Watercraft control functions ......... 26
Remote control transmitter .............. 26
Yamaha Security System ................ 27
Engine stop switch .......................... 28
Engine shut-off switch ..................... 28
Start switch ...................................... 28
Throttle lever ................................... 29
Steering system ............................... 29
Adjustable tilt steering system ......... 30
Cooling water pilot outlet ................. 30
Water separator ............................... 31
Watercraft operation ....................... 32
Watercraft operation functions ..... 32
Reverse system ............................... 32
Quick Shift Trim System
(Q.S.T.S.) ..................................... 33
Watercraft operation modes ......... 34
Low RPM Mode ............................... 34
No-wake mode ................................ 35
Cruise assist .................................... 36
Instrument operation ...................... 39
Multifunction information center ... 39
Analog speedometer/tachometer .... 39
Information display .......................... 40
Equipment operation ...................... 45
Equipment .................................... 45
Seats ............................................... 45
Handgrip .......................................... 46
Reboarding step .............................. 46
Bow eye ........................................... 47
Stern eyes ....................................... 47
Cleat ................................................ 47
Pull-up cleats (FX Cruiser HO) ........ 48
Storage compartments .................... 48
Fire extinguisher container .............. 51
Operation and handling
requirements ................................... 52
Fuel requirements ........................ 52
Fuel ................................................. 52
Engine oil requirements ............... 54
Engine oil ......................................... 54
Draining the bilge water ............... 55
Draining the bilge water on land ...... 55
Draining the bilge water on water .... 56
Transporting on a trailer ............... 57
First-time operation ........................ 58
Engine break-in ............................ 58
Pre-operation checks ..................... 59
Pre-operation checklist .................... 59
UF2H71E0.book Page 1 Thursday, July 2, 2009 10:05 AM
Page 42 of 110
Watercraft operation
35
TIP:
If the remote control transmitter is operated
while the multifunction information center is in
the standby state, the center performs the ini-
tial operation, and then the setting is selected.
To activate the Low RPM Mode:
Push the “L-Mode” (unlock) button on the re-
mote control transmitter for more than 4 sec-
onds. Once the beeper sounds three times
and the “UNLOCK” indicator light blinks three
times, then comes on, the “L-MODE” indicator
light comes on and the Low RPM Mode is ac-
tivated.
TIP:
If the Low RPM Mode is activated immediate-
ly after the information display turns off, the
“L-MODE” indicator light will not come on. The
“L-MODE” indicator light will come on when
the engine is started.
To deactivate the Low RPM Mode:
Push the “L-Mode” (unlock) button on the re-
mote control transmitter for more than 4 sec-onds. Once the beeper sounds two times and
the “UNLOCK” indicator light blinks two times,
then comes on, the “L-MODE” indicator light
goes off and the Low RPM Mode is deactivat-
ed. When the Low RPM Mode is deactivated,
the watercraft returns to the normal operation
mode.
EJU37015No-wake mode
The no-wake mode is a function that main-
tains the engine speed at a fixed setting for
operating the watercraft at low speeds. This
function can be used only for forward opera-
tion of the watercraft.
TIP:
The no-wake mode can only be activated af-
ter 5 seconds have elapsed since starting the
engine.
Activating and deactivating the no-wake
mode
Activation of the no-wake mode will be con-
firmed by the number of beeps when the “NO-
WAKE MODE” switch is pushed, and by the
digital speedometer display of the multifunc-
tion information center. (See page 39 for infor-
mation on the multifunction information
center.)
TIP:
The beeps and the blinking digital speedome-
ter display also indicate the activation of the
cruise assist. (See page 36 for information on
the cruise assist.)
Number of
beepsLow RPM Mode
operation“L-
MODE”
indicator
light
ActivatedComes
on
Deactivated Goes off
1“L-Mode” (unlock) button
2“L-MODE” indicator light
L-MODE
L-Mode12Number
of beepsNo-wake mode oper-
ationDigital
speedome-
ter display
ActivatedStarts
blinking
DeactivatedStops
blinking
UF2H71E0.book Page 35 Thursday, July 2, 2009 10:05 AM
Page 43 of 110
Watercraft operation
36
To activate the no-wake mode:
(1) Release the throttle lever and let the en-
gine speed return to idle.
(2) Make sure that the shift lever is in the for-
ward position. The no-wake mode cannot
be activated when the shift lever is in the
reverse position.
(3) Push and hold the “NO-WAKE MODE”
switch. Once the beeper sounds three
times quickly and “8” (when kilometers
are selected) or “5” (when miles are se-
lected) starts blinking in the digital speed-
ometer display, the no-wake mode is
activated. Keep the throttle lever in the
fully closed (idle) position when the no-
wake mode is activated.TIP:
The digital speedometer display blinks contin-
ually while the no-wake mode is activated.
To deactivate the no-wake mode:
Perform one of the following operations. The
beeper sounds two times quickly and the dig-
ital speedometer display stops blinking when
the no-wake mode is deactivated.
Push the “NO-WAKE MODE” switch.
Squeeze the throttle lever.
TIP:
The no-wake mode is also deactivated when
the engine is stopped.
EJU37025Cruise assist
The cruise assist is a function for maintaining
a desired engine speed within a fixed range
while operating the watercraft.
1Shift lever
2Forward position
1
2
1“NO-WAKE MODE” sw itch
1
UF2H71E0.book Page 36 Thursday, July 2, 2009 10:05 AM
Page 44 of 110
Watercraft operation
37
TIP:
The cruise assist can only be set between
engine speeds of approximately 3000 r/min
and approximately 7000 r/min.
The cruise assist cannot be activated in the
Low RPM Mode. (See page 34 for Low
RPM Mode activation procedures.)
Activating and deactivating the cruise as-
sist
Activation of the cruise assist will be con-
firmed by the number of beeps when the
“SET” switch, up switch, or down switch is
pushed, and by the digital speedometer dis-
play of the multifunction information center.
(See page 39 for information on the multifunc-
tion information center.)
TIP:
The beeps and the blinking digital speedome-
ter display also indicate the activation of the
no-wake mode. (See page 35 for information
on the no-wake mode.)
To activate the cruise assist:
(1) Operate the throttle lever until the desired
engine speed is reached.
(2) When the engine speed reaches the de-
sired cruise assist setting, push the “SET”
switch. Once the beeper sounds three
times quickly and the digital speedometer
display starts blinking, the cruise assist is
activated. When the cruise assist is acti-
vated, slowly squeeze the throttle lever to
keep it squeezed further than the positionat which the cruise assist was set; releas-
ing the throttle lever will deactivate the
cruise assist.
TIP:
The digital speedometer display blinks contin-
ually while the cruise assist is activated. Make
sure that the beeper has sounded and the dig-
ital speedometer display is blinking before
squeezing the throttle lever to the full throttle
position. If the speedometer display is not
blinking, the cruise assist is not activated and
Number
of beepsCruise assist opera-
tionDigital
speedome-
ter display
ActivatedStarts
blinking
DeactivatedStops
blinking
Set engine speed in-
creases or decreasesContinues
blinking
UF2H71E0.book Page 37 Thursday, July 2, 2009 10:05 AM
Page 45 of 110
Watercraft operation
38
the engine will respond normally to the throttle
operation.
TIP:
Once the cruise assist is activated, the set en-
gine speed can be increased by pushing the
up switch or decreased by pushing the down
switch. Each time a switch is pushed, the
beeper will sound one time quickly and the setengine speed will change. However, the ad-
justment is limited to a maximum of five incre-
ments above or below the initial cruise assist
setting.
To deactivate the cruise assist:
Relax your grip on the throttle lever. The
beeper sounds two times quickly and the dig-
ital speedometer display stops blinking when
the cruise assist is deactivated.
TIP:
The cruise assist is also deactivated when the
engine is stopped.
1Up switch
2Down switch
3“SET” sw itch
1
2
3
UF2H71E0.book Page 38 Thursday, July 2, 2009 10:05 AM
Page 46 of 110
Instrument operation
39
EJU34906
Multifunction information
center
The multifunction information center displays
various watercraft information.
Multifunction information center initial op-
eration
When the multifunction information center is
activated, the analog speedometer/tachome-
ter makes one sweep, all of the display seg-
ments and indicator lights come on. After 2
seconds, the “WARNING” indicator light and
the warning indicators in the information dis-
play go off, and then the center starts to oper-
ate normally.
TIP:
The “UNLOCK” indicator light will go off when
the engine is started.
Multifunction information center standby
state
If the multifunction information center does
not receive any operation input within 25 sec-
onds after the engine stops, the center will
turn off and enter a standby state. When the
engine is started again, the displays return to
their state before the center turned off, and
then the center starts to operate normally.
EJU36794Analog speedometer/tachometer
The analog speedometer/tachometer has
both a speedometer function and a tachome-
ter function. By switching the meter, it can be
used as either a speedometer or a tachome-
ter.
TIP:
The analog speedometer is selected at the
Yamaha factory.
Analog speedometer
The analog speedometer shows the water-
craft speed against water.
The small outer numbers on the meter show
the watercraft speed in kilometers per hour
“km/h” and the large inner numbers show the
speed in miles per hour “mph”.
The “SPEED” indicator light comes on when
the analog speedometer is selected.
To switch to the speedometer from the ta-
chometer:
Push the “Speed/RPM” button for at least 1
second after the multifunction information
center is activated. When the meter switches
to the analog speedometer function, the
“SPEED” indicator light comes on if “km/h” are
selected as the display units. The “SPEED”
indicator light blinks three times, then comes
on, if “mph” are selected as the display units.
1“Volt/Hour” button
2“Speed/RPM” button
3Information display
4Analog speedometer/tachometer
3421
UF2H71E0.book Page 39 Thursday, July 2, 2009 10:05 AM
Page 47 of 110
Instrument operation
40
(See page 40 for information on switching the
digital speedometer display units.)
Analog tachometer
The analog tachometer shows the engine
speed.
The large inner numbers on the meter show
the engine speed × 100 rpm (r/min).
The “RPM” indicator light comes on when the
analog tachometer is selected.
To switch to the tachometer from the speed-
ometer:
Push the “Speed/RPM” button for at least 1
second after the multifunction information
center is activated. When the meter switches
to the analog tachometer function, the “RPM”
indicator light comes on.
EJU35024Information display
The information display shows watercraft op-
erating conditions.
EJU37084Digital speedometer
The digital speedometer shows the watercraft
speed against water.
By switching the display units, the speed can
be shown in kilometers per hour (km/h) or
miles per hour (mph).
TIP:
Kilometers are selected as the display units at
the Yamaha factory.
1“Speed/RPM” button
2“SPEED” indicator light
1“Speed/RPM” button
2“RPM” indicator light
2
1
1
2
1Fuel level meter
2Fuel indicator
3Hour meter/voltmeter
4Digital speedometer
5Engine overheat warning indicator
6Check engine warning indicator
7Oil pressure warning indicator
1Digital speedometer
1
UF2H71E0.book Page 40 Thursday, July 2, 2009 10:05 AM
Page 48 of 110
Instrument operation
41
Digital speedometer display (km/h)
The “SPEED” indicator light blinks once if kilo-
meters are selected as the display units when
the multifunction information center is activat-
ed.
TIP:
If the analog speedometer is selected, the
“SPEED” indicator light blinks once, then
comes on.
Digital speedometer display (mph)
The “SPEED” indicator light blinks three times
if miles are selected as the display units when
the multifunction information center is activat-
ed.
TIP:
If the analog speedometer is selected, the
“SPEED” indicator light blinks three times,
then comes on.
To switch the digital speedometer display
units:
Push the “Volt/Hour” button for at least 1 sec-
ond, within 10 seconds after the multifunction
information center is activated. The digital
speedometer display changes. When the dis-
play units are switched from kilometers to
miles only, the “SPEED” indicator light blinks
three times.
EJU35064Hour meter/voltmeter
The hour meter/voltmeter has both an hour
meter function and a voltmeter function. By
switching the meter, it can be used as either
an hour meter or a voltmeter.
TIP:
The hour meter is selected at the Yamaha
factory.
Hour meter
The hour meter shows the total number of
hours that the engine has been running since
the watercraft was new.
TIP:
The elapsed time will be kept even if the bat-
tery terminals have been disconnected.
To switch to the hour meter from the voltme-
ter:
Push the “Volt/Hour” button for at least 1 sec-
ond after the multifunction information center
is activated for more than 10 seconds. The
1“Volt/Hour” button
2“SPEED” indicator light
1
2
1Hour meter/voltmeter
1
UF2H71E0.book Page 41 Thursday, July 2, 2009 10:05 AM
Page 49 of 110
Instrument operation
42
display switches to the hour meter from the
voltmeter.
Voltmeter
The voltmeter shows the battery voltage.
When the battery voltage is normal, the volt-
meter displays approximately 12 volts.
If the battery voltage has dropped significant-
ly, “LO” is displayed on the voltmeter. If the
battery voltage has risen significantly, “HI” is
displayed. If “LO” or “HI” is displayed, immedi-
ately return to shore and have a Yamaha
dealer service the watercraft.
To switch to the voltmeter from the hour
meter:
Push the “Volt/Hour” button for at least 1 sec-
ond after the multifunction information center
is activated for more than 10 seconds. The
display switches to the voltmeter from the
hour meter.
EJU31514Fuel level meter
The fuel level meter shows the amount of fuel
remaining in the fuel tank. The amount of re-
maining fuel is shown using eight display seg-
ments, which disappear two at a time as the
fuel level decreases.
TIP:
The accuracy of the fuel level meter varies de-
pending on the operating conditions. Use this
function as a reference only.
EJU36815Fuel level warning
If the fuel remaining in the fuel tank drops to
about 18 L (4.8 US gal, 4.0 Imp. gal), the
“WARNING” indicator light, the fuel indicator,
and the lowest two fuel level segments blink,
and the buzzer sounds intermittently.
If the fuel level warning is activated, refill the
fuel tank as soon as possible. (See page 52
for information on filling the fuel tank.)
1“Volt/Hour” button
2Hour meter
1“Volt/Hour” button
2Vo l t m e t e r
1Fuel level meter
1
UF2H71E0.book Page 42 Thursday, July 2, 2009 10:05 AM
Page 107 of 110
Index
A
Adjustable tilt steering system.................. 30
Adjustable tilt steering system checks ..... 63
After removing the watercraft
from the water ....................................... 80
Analog speedometer/tachometer ............. 39
B
Battery care .............................................. 82
Battery checks.......................................... 62
Battery, jumping ....................................... 97
Beaching and docking the watercraft ....... 79
Beverage holder ....................................... 51
Bilge water check ..................................... 62
Bilge water, draining................................. 55
Bilge water, draining on land .................... 55
Bilge water, draining on water .................. 56
Boarding alone ......................................... 75
Boarding and starting off from a dock ...... 78
Boarding the watercraft ............................ 74
Boarding with passenger(s) ..................... 75
Bow eye ................................................... 47
Bow storage compartment ....................... 48
Builder’s plate............................................. 2
C
Capsized watercraft ................................. 78
Check engine warning.............................. 44
Cleaning ................................................... 85
Cleaning the watercraft ............................ 82
Cleat ......................................................... 47
Cooling water pilot outlet .......................... 30
Cooling water pilot outlet check ............... 68
Craft Identification Number (CIN) ............... 1
Cruise assist............................................. 36
Cruising limitations ................................... 11
D
Digital speedometer ................................. 40
E
Emergency procedures ............................ 96
Engine break-in ........................................ 58
Engine compartment check...................... 61
Engine cover, removing and installing ..... 87
Engine idling speed check ....................... 68
Engine oil ................................................. 54
Engine oil and oil filter .............................. 91
Engine oil level check............................... 62Engine oil requirements ........................... 54
Engine overheat warning ......................... 43
Engine serial number ................................. 1
Engine shut-off cord (lanyard) check ....... 65
Engine shut-off switch .............................. 28
Engine stop switch ................................... 28
Engine unit check ..................................... 62
Enjoy your watercraft responsibly ............ 19
Equipment ................................................ 45
F
Fire extinguisher check ............................ 66
Fire extinguisher container ....................... 51
Fire extinguisher container checks ........... 66
Flushing the cooling water passages ....... 81
Fuel .......................................................... 52
Fuel level check ....................................... 61
Fuel level meter ........................................ 42
Fuel level warning .................................... 42
Fuel requirements .................................... 52
Fuel system checks .................................. 61
Fuses, replacing ....................................... 97
G
Getting to know your watercraft ............... 69
Glossary, watercraft ................................. 21
Glove compartment .................................. 49
H
Handgrip ................................................... 46
Hazard information ................................... 15
Hood check .............................................. 67
Hour meter/voltmeter ............................... 41
Hull and deck check ................................. 67
I
Identification numbers ................................ 1
Information display ................................... 40
J
Jet intake and impeller, cleaning .............. 96
Jet intake checks ...................................... 67
Jumper cables, connecting ...................... 97
L
Labels, important ........................................ 3
Labels, other .............................................. 8
Labels, warning .......................................... 4
Launching the watercraft .......................... 70
Learning to operate your watercraft ......... 69
Leaving the watercraft .............................. 71
UF2H71E0.book Page 1 Thursday, July 2, 2009 10:05 AM