check engine YAMAHA FX HO CRUISER 2006 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2006, Model line: FX HO CRUISER, Model: YAMAHA FX HO CRUISER 2006Pages: 152, PDF Size: 11.96 MB
Page 24 of 152
1-17
E
Do not attempt to modify this watercraft!
Modifications to your watercraft may
reduce safety and reliability, and render
the watercraft unsafe or illegal for use.
Attach the engine shut-off cord (lanyard)
to your wrist and keep it free from the
handlebars so that the engine stops if the
operator falls off. After riding, remove the
engine shut-off cord from the watercraft to
avoid accidental starting or unauthorized
use by children or others.
Scan carefully for swimmers and stay
away from swimming areas. Swimmers
are hard to see and you could acciden-
tally hit someone in the water.
Avoid being hit by another boat! You
should always take the responsibility to
watch for traffic; other boaters may not be
watching for you. If they do not see you,
or if you maneuver more quickly than
other boaters expect, you risk a collision.
Maintain a safe distance from other boats
and watercraft, and also watch for ski
ropes or fishing lines. Obey the “Safe
boating rules,” and be sure to check
behind you before making a turn. (See
Safe boating rules on page 1-21.)
EJU13820
Recommended equipment
The following items should be carried on
board your watercraft:
Sound-signaling device
You should carry a whistle or other sound-
signaling device that can be used to sig-
nal other boats.
Visual distress signals
It is recommended that an authority-
approved pyrotechnic device be stored in
a waterproof container on your watercraft.
A mirror can also be used as an emer-
gency signal. Contact your Yamaha
dealer for more information.
Watch
A watch is helpful so you will know how
long you have been operating.
Towline
A towline can be used to tow a disabled
watercraft in an emergency.
E_F1X-70.book Page 17 Friday, August 26, 2005 11:00 AM
Page 32 of 152
2-3
E
1Quick Shift Trim System (QSTS) selector
Use to select the trim angle of the watercraft.
2QSTS shift lock lever
3Start switch
Push to start the engine.
4Engine shut-off switch
Remove the clip to stop the engine and dis-
able it from starting.
5Clip
Insert into the engine shut-off switch to enable
starting of the engine.
Remove to stop the engine or prevent acci-
dental star ting of the engine or unauthorized
use of the watercraft.
6Rearview mirrors
7Multifunction meter
Use to check watercraft operation.8Shift lever
Use to put the watercraft into forward or
reverse.
9Throttle lever
Use to accelerate and decelerate.
0Tilt lever
Use to adjust the tilt of the handlebars.
AGlove compartment
BRemote control transmitter
CEngine stop switch
Push to stop the engine normally.
DEngine shut-off cord (lanyard)
Attach to wrist so that the engine stops if the
operator falls off the watercraft.
EWatertight compartment
FBeverage holder
E_F1X-70.book Page 3 Friday, August 26, 2005 11:00 AM
Page 41 of 152
2-12
E
EJU17840
Cooling water pilot outlet
This watercraft is equipped with cooling
water pilot outlets.
When the engine is running, cooling
water is circulated in the engine, and then it
is discharged from the pilot outlets.
To check for proper operation of the cool-
ing system, check that water is being dis-
charged from the port (left) pilot outlet. If
water is not being discharged from this out-
let, cooling water may not be circulating in
the engine. When this occurs, stop the
engine and check for the cause. (See pages
2-30 and 5-3 for further instructions.)
NOTE:@ If the cooling water passages are dry, it
will take about 60 seconds for the water to
reach the outlet after the engine is
started.
Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.
Water discharge may not be constant at
the starboard (right) pilot outlet, however,
if it is constant at the port (left) pilot outlet,
the cooling system is operating normally.
@
E_F1X-70.book Page 12 Friday, August 26, 2005 11:00 AM
Page 52 of 152
2-23
E
CAUTION:@ If the remote control transmitter does not
operate when its buttons are pressed,
the battery may be low. Have a Yamaha
dealer replace the battery.
@
EJU22240
Multifunction meter
The multifunction meter is equipped with
the following three main components for
help and convenience in operating the
watercraft.
1
Analog speedometer/tachometer and indicator
lights
2
Left multifunction display and operation but-
tons
3
Right multifunction display and operation but-
tons (for FX Cruiser High Output)
CAUTION:@ Do not run the engine for more than 15
seconds when checking the operation of
the meter on land. The engine could
overheat.
@
NOTE:@ When the multifunction meter starts oper-
ating, the analog speedometer/tachome-
ter makes one sweep, all displays light up
for 2 seconds, and then the meter starts
to operate normally.
The multifunction meter will continue to
operate for 25 seconds after the engine
stops.
@
E_F1X-70.book Page 23 Friday, August 26, 2005 11:00 AM
Page 56 of 152
2-27
E
EJU22040
Left multifunction display and
operation buttons
The left multifunction display is equipped
with the following functions.
1
Digital speedometer
2
Fuel meter
3
Hour meter/Voltmeter
4
Check engine warning indicator
5
Fuel warning indicator
6
Oil pressure warning indicator
7
Engine overheat warning indicator
The following operation buttons are on the
left side of the multifunction meter.
8
“Volt/Hour” button
9
“Speed/RPM” button
EJU22270
Digital speedometer
The digital speedometer 1
shows the
watercraft speed against water.
NOTE:@ To switch the speedometer display
between kilometers and miles, push the
“Vo l t / H o u r” button 2
for at least 1 second,
within 10 seconds after the multifunction
meter starts operating.
The “SPEED” indicator light 3
blinks
three times if miles are selected as the
display units when the multifunction meter
starts operating, or if the display units of
the meter are switched to miles.
@
E_F1X-70.book Page 27 Friday, August 26, 2005 11:00 AM
Page 57 of 152
2-28
E
EJU17890
Fuel meter
The fuel meter is provided for convenient
fuel level checking while riding. The fuel
meter has eight segments which show the
amount of fuel remaining in the fuel tank.
NOTE:@ The fuel level is most accurate when the
watercraft is sitting level on a trailer or in the
water.
@
EJU22050
Hour meter/Voltmeter
NOTE:@ To switch the display between the hour
meter and voltmeter, push the “Vo l t / H o u r”
button 1 for at least 1 second after the
meter is displayed for more than 10 sec-
onds.
@
Hour meter
The hour meter is provided to make it
easy to follow the maintenance schedule.
The meter shows the hours of engine
operation that have elapsed since the water-
craft was new.
Vo l t m e t e r
The voltmeter is provided to display the
voltage of the battery.
When the battery voltage is normal, the
voltmeter displays approximately 12 volts.
If the battery voltage is less than 8.0 volts,
“LO” is displayed on the voltmeter and if the
voltage is above 18.1 volts, “HI” is displayed
on the voltmeter. If “HI” or “LO” is displayed,
return to shore and, if necessary, have a
Yamaha dealer check the charging system
and the battery.
E_F1X-70.book Page 28 Friday, August 26, 2005 11:00 AM
Page 58 of 152
2-29
E
EJU22060
Check engine warning indicator
If a sensor malfunction or a short circuit is
detected, the “WARNING” indicator light and
the check engine warning indicator begin to
blink and the buzzer sounds intermittently.
If this occurs, reduce the engine speed,
return to shore, and have a Yamaha dealer
check the engine.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22070
Fuel warning indicator
If the fuel remaining in the tank drops to
about 13 L (3.4 US gal, 2.9 Imp gal), the
lowest two fuel level segments, the fuel
warning indicator, and the “WARNING” indi-
cator light all begin to blink. The buzzer also
starts sounding intermittently.
The warning signals will be cleared when
the engine is restarted after refilling.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
E_F1X-70.book Page 29 Friday, August 26, 2005 11:00 AM
Page 59 of 152
2-30
E
EJU22080
Oil pressure warning indicator
If the oil pressure does not rise to specifi-
cation, the “WARNING” indicator light and
the oil pressure warning indicator begin to
blink and the buzzer sounds intermittently.
At the same time, the engine speed is lim-
ited to help prevent damage.
If this occurs, reduce the engine speed,
return to shore, and then check the engine
oil level. (See page 3-7 for engine oil level
checking procedures.) If the oil level is low,
add enough engine oil to raise it to the
proper level. If the oil level is sufficient, have
a Yamaha dealer check the watercraft.
NOTE:@ Press any button on the multifunction meter
to stop the buzzer.
@
EJU22090
Engine overheat warning indicator
This model is equipped with an engine
overheat warning system.
If the engine starts to overheat, the
“WARNING” indicator light and the overheat
warning indicator blink, and then come on.
The buzzer also begins to sound intermit-
tently, and then it sounds continuously. After
the light and indicator start to blink and the
buzzer sounds, the engine speed is limited
to help prevent damage.
If this occurs, immediately reduce the
engine speed, return to shore, and then
check for water discharge at the port (left)
cooling water pilot outlet. If there is no dis-
charge of water, check the intake grate and
impeller for clogging.
E_F1X-70.book Page 30 Friday, August 26, 2005 11:00 AM
Page 69 of 152
E
3
EJU10400
OPERATION
Fuel and oil ............................................... 3-1
Gasoline ................................................. 3-1
Engine oil ................................................ 3-3
Filling the fuel tank ................................. 3-4
Pre-operation checks .............................. 3-5
Pre-operation check list ......................... 3-5
Pre-operation check points .................... 3-6
Operation ................................................ 3-17
Engine break-in .................................... 3-17
Launching the watercraft ..................... 3-18
Starting the engine ............................... 3-19
Stopping the engine ............................. 3-21
Leaving the watercraft ......................... 3-21
Operating your watercraft .................... 3-22
Getting to know your watercraft ........... 3-22
Learning to operate your watercraft .... 3-22
Riding watercraft with passengers ...... 3-23
Starting the watercraft .......................... 3-24
Boarding and starting in deep water ... 3-26
Capsized watercraft ............................. 3-29
Turning the watercraft .......................... 3-31
Stopping the watercraft ........................ 3-33
Beaching the watercraft ....................... 3-34
Docking the watercraft ......................... 3-34
Reverse on waterways ......................... 3-35
Rough water operation ........................ 3-35
Post-operation checks ......................... 3-36
Transporting .......................................... 3-38
E_F1X-70.book Page 1 Friday, August 26, 2005 11:00 AM
Page 74 of 152
3-5
E
EJU13460
Pre-operation checks
EJU13470
Pre-operation check list
Before operating this watercraft, perform the checks in the following check list. See the
accompanying text in this chapter for details on how to perform the checks.
WARNING@ If any item in the pre-operation check list is not working properly, have it inspected
and repaired before operating the watercraft, otherwise an accident could occur.
@
NOTE:@ Pre-operation checks should be made thoroughly each time the watercraft is used. This pro-
cedure can be completed in a short time. It is worth the time spent to assure safety and reli-
ability.
@
ITEM ROUTINE PAGE
Engine compartment Remove all seats to ventilate the engine compartment.
Check for fuel vapors and loose electrical connections.3-6
Bilge Check for water and fuel and remove if necessary. 3-9
Stern drain plugs Check for proper installation. 3-10
Throttle lever Check that the throttle lever springs back smoothly. 3-12
Steering system Check for proper operation.
Check that the handlebars are securely locked.3-12
Shift lever and reverse gate Check for proper operation. 3-13
QSTS Check for proper operation. 3-14
Fuel and oil Check fuel and oil levels and add if necessary.
Check the hoses and tanks for leakage.3-6, 3-7
Water separator Check for water and drain if necessary. 3-8
Battery Check electrolyte level and battery condition. 3-10
Hood Check that the hood is properly secured. 2-7
Front and rear seats Check that the seats are properly secured. 2-5, 2-6
Hull and deck Check the hull and deck for cracks or other damage. 3-6
Jet unit Check for debris and remove if necessary. 3-15
Fire extinguisher Check condition and replace if necessary. 3-11
Engine shut-off cord Check condition and replace if frayed or broken. 3-15
Switches Check the start switch, engine stop switch, and engine
shut-off switch for proper operation.3-16
Cooling water pilot outlet Check that water is discharged while the engine is run-
ning and the watercraft is in the water.3-16
Multifunction meter Check for warning indications and proper operation. 3-16
E_F1X-70.book Page 5 Friday, August 26, 2005 11:00 AM