check engine YAMAHA FX HO CRUISER 2007 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2007, Model line: FX HO CRUISER, Model: YAMAHA FX HO CRUISER 2007Pages: 108, PDF Size: 7.59 MB
Page 6 of 108
Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Hull Identification Number (HIN) ........ 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 8
Safety information ........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 12
Recommended equipment ........... 14
Hazard information ....................... 15
Watercraft characteristics ............. 15
Water-skiing ................................. 17
Safe boating rules ........................ 19
Enjoy your watercraft
responsibly ................................ 19
Features and functions ................... 20
Location of main components ...... 20
Operation of controls and
other functions ........................... 24
Seats ............................................... 24
Hood ................................................ 25
Fuel tank filler cap ........................... 26
Remote control transmitter .............. 26
Engine stop switch .......................... 27
Engine shut-off switch ..................... 27
Start switch ...................................... 27
Throttle lever ................................... 28
Cooling water pilot outlets ............... 28
Steering system ............................... 28
Tilt lever ........................................... 29
Shift lever ......................................... 29
Quick Shift Trim System (QSTS)
selector ........................................ 30Handgrip .......................................... 32
Reboarding step ............................... 32
Bow eye ........................................... 32
Stern eyes ....................................... 33
Pull-up cleats
(for FX Cruiser High Output) ........ 33
Yamaha Engine Management
System (YEMS) ........................... 33
Yamaha Security System ................ 33
Multifunction information center ...... 34
Storage compartments .................... 45
Operation ......................................... 49
Fuel and oil .................................. 49
Gasoline .......................................... 49
Engine oil ......................................... 50
Filling the fuel tank .......................... 50
Pre-operation checks ................... 51
Pre-operation check list ................... 51
Pre-operation check points .............. 53
Operation ..................................... 61
Engine break-in ............................... 61
Launching the watercraft ................. 61
Starting the engine .......................... 61
Stopping the engine ........................ 63
Leaving the watercraft ..................... 63
Operating your watercraft ............ 64
Getting to know your watercraft ....... 64
Learning to operate your
watercraft ..................................... 64
Riding with passengers ................... 65
Starting the watercraft ..................... 65
Boarding and starting in
deep water ................................... 66
Capsized watercraft ......................... 69
Turning the watercraft ..................... 70
Stopping the watercraft ................... 72
Beaching the watercraft ................... 72
Docking the watercraft ..................... 72
Reverse on waterways ..................... 72
Rough water operation .................... 73
UF1X71E0.book Page 1 Tuesday, September 26, 2006 9:52 AM
Page 7 of 108
Table of contents
Post-operation care ...................... 73
Transporting ................................. 75
Maintenance and care ..................... 76
Storage ......................................... 76
Flushing the cooling system ............ 76
Lubrication ....................................... 77
Fuel system ..................................... 77
Battery ............................................. 78
Cleaning the watercraft ................... 78
Maintenance and adjustments ..... 79
Owner’s/operator’s manual and
tool kit ........................................... 80
Periodic maintenance chart ............. 81
Checking the fuel system ................ 83
Engine oil and oil filter ..................... 83
Checking the air filter element ......... 84
Checking the jet thrust nozzle
angle ............................................ 85
Checking the shift cable .................. 85
Checking and adjusting the throttle
cable ............................................ 85
Cleaning and adjusting
the spark plugs ............................. 86
Lubrication points ............................ 87
Checking the battery ....................... 88
Fuel injection system ....................... 90
Specifications .................................. 91
Specifications ................................ 91
Trouble recovery ............................. 92
Troubleshooting ........................... 92
Troubleshooting chart ...................... 92
Emergency procedures ................ 94
Cleaning the jet intake and
impeller ........................................ 94
Jumping the battery ......................... 95
Replacing the fuses ......................... 96
Towing the watercraft ...................... 97
Submerged watercraft ..................... 97
UF1X71E0.book Page 2 Tuesday, September 26, 2006 9:52 AM
Page 21 of 108
Safety information
14
Always consult your doctor on whether it is
safe for you to ride this watercraft if you are
pregnant or in poor health.
Do not attempt to modify this watercraft!
Modifications to your watercraft may reduce
safety and reliability, and render the water-
craft unsafe or illegal for use.
Attach the engine shut-off cord to your left
wrist and keep it free from the handlebars
so that the engine stops if you, the operator,
fall off. After riding, remove the engine shut-
off cord from the watercraft to avoid acci-
dental starting or unauthorized use by chil-
dren or others.
Scan carefully for swimmers and stay away
from swimming areas. Swimmers are hard
to see and you could accidentally hit some-
one in the water.
Avoid being hit by another boat! You should
always take the responsibility to watch for
traffic; other boaters may not be watching
for you. If they do not see you, or if you ma-
neuver more quickly than other boaters ex-
pect, you risk a collision.
Maintain a safe distance from other boats
and watercraft, and also watch for ski ropes
or fishing lines. Obey the “Safe boating
rules” and be sure to check behind you be-
fore making a turn. (See “Safe boating
rules” on page 19.)
EJU30840
Recommended equipment
The following items should be carried on
board your watercraft:
Sound-signaling device
You should carry a whistle or other sound-
signaling device that can be used to signal
other boats.
Visual distress signals
It is recommended that a pyrotechnic de-
vice, which is approved by the appropriate
authorities, be stored in a waterproof con-
tainer on your watercraft. A mirror can also
be used as an emergency signal. Contact a
Yamaha dealer for more information.
Watch
A watch is helpful so you will know how long
you have been operating the watercraft.
Towline
A towline can be used to tow a disabled wa-
tercraft in an emergency.
UF1X71E0.book Page 14 Tuesday, September 26, 2006 9:52 AM
Page 35 of 108
Features and functions
28
squeezed. (See page 33 for Yamaha Security
System lock and unlock mode selection pro-
cedures.)
EJU31210Throttle lever
Squeeze the throttle lever to increase engine
speed.
Release the throttle lever to decrease engine
speed or to return it to the idle position.
EJU31240Cooling water pilot outlets
This watercraft is equipped with cooling water
pilot outlets.
When the engine is running, cooling water is
circulated in the engine, and then it is dis-
charged from the pilot outlets.
To check for proper operation of the cooling
system, check that water is being discharged
from the port (left) pilot outlet. If water is not
being discharged from this outlet, cooling wa-
ter may not be circulating in the engine. Whenthis occurs, stop the engine and check for the
cause. (See pages 40 and 94 for more infor-
mation.)
NOTE:
If the cooling water passages are dry, it will
take about 60 seconds for the water to
reach the outlet after the engine is started.
Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.
Water discharge may not be constant at the
starboard (right) pilot outlet, however, if it is
constant at the port (left) pilot outlet, the
cooling system is operating normally.
EJU31260Steering system
Your watercraft can be steered by turning the
handlebars in the direction you wish to travel.
When the handlebars are turned, the angle of
the jet thrust nozzle is changed, and the direc-
tion of the watercraft is changed accordingly.
Since the strength of the jet thrust determines1Throttle lever
1Handlebar
2Jet thrust nozzle
UF1X71E0.book Page 28 Tuesday, September 26, 2006 9:52 AM
Page 42 of 108
Features and functions
35
ponents for help and convenience in operat-
ing the watercraft.
CAUTION:
ECJ00941
Do not run the engine for more than 15
seconds without supplying water or over
6000 r/min on land when checking the op-
eration of the multifunction information
center, otherwise the engine could over-
heat.
NOTE:
When the multifunction information center
starts operating, the analog speedome-
ter/tachometer makes one sweep, all dis-
plays light up for 2 seconds, and then it
starts to operate normally.
The multifunction information center will
continue to operate for 25 seconds after the
engine stops.
EJU34930Analog speedometer/tachometer and indi-
cator lights
This watercraft is equipped with the following
meter and indicator lights.
EJU34941Analog speedometer/tachometer
The analog speedometer/tachometer can be
used as a speedometer or a tachometer.
To switch between the speedometer and the
tachometer functions, push the “Speed/RPM”
button for at least 1 second when the multi-
function information center is operating.
The “SPEED” indicator light comes on when
the analog speedometer is selected. The
1Analog speedometer/tachometer and indi-
cator lights
2Left multifunction display and operation but-
tons
3Right multifunction display and operation
buttons (for FX Cruiser High Output)
1Analog speedometer/tachometer
2“SPEED” indicator light
3“WARNING” indicator light
4“RPM” indicator light
5“UNLOCK” indicator light
UF1X71E0.book Page 35 Tuesday, September 26, 2006 9:52 AM
Page 44 of 108
Features and functions
37
EJU34980“WARNING” indicator light
The “WARNING” indicator light blinks or
comes on, together with a warning indicator,
when a malfunction has occurred.
EJU34990“UNLOCK” indicator light
The “UNLOCK” indicator light comes on when
the unlock mode of the Yamaha Security Sys-
tem is selected. The watercraft can be ridden
normally when this light is on. (See page 33
for more information.)
EJU35021Left multifunction display and operation
buttons
The left multifunction display is equipped with
the following functions.
The following operation buttons are on the left
side of the multifunction information center.
1“WARNING” indicator light
1“UNLOCK” indicator light1Fuel level meter
2Fuel level warning indicator
3Hour meter/voltmeter
4Digital speedometer
5Oil pressure warning indicator
6Exhaust temperature warning indicator
7Check engine warning indicator
8Engine overheat warning indicator
1“Speed/RPM” button
2“Volt/Hour” button
UF1X71E0.book Page 37 Tuesday, September 26, 2006 9:52 AM
Page 46 of 108
Features and functions
39
The fuel level meter has eight segments
which show the amount of fuel remaining in
the fuel tank.
NOTE:
The fuel level is most accurate when the wa-
tercraft is sitting level on a trailer or in the wa-
ter.
EJU35060Hour meter/voltmeter
NOTE:
To switch the display between the hour meter
and the voltmeter, push the “Volt/Hour” button
for at least 1 second after the meter is dis-
played for more than 10 seconds.
Hour meter
The hour meter is provided to make it easy to
follow the maintenance schedule.The meter shows the hours of engine opera-
tion that have elapsed since the watercraft
was new.
Voltmeter
The voltmeter is provided to display the volt-
age of the battery.
When the battery voltage is normal, the volt-
meter displays approximately 12 volts.
If the battery voltage is less than 8.0 volts,
“LO” is displayed on the voltmeter and if the
voltage is above 18.1 volts, “HI” is displayed
on the voltmeter. If “HI” or “LO” is displayed,
return to shore and, if necessary, have a
Yamaha dealer check the charging system
and the battery.
EJU35072Fuel level warning indicator
If the fuel remaining in the fuel tank drops to
about 13 L (3.4 US gal, 2.9 Imp gal), the low-
est two fuel level segments, the fuel level
warning indicator, and the “WARNING” indi-
cator light begin to blink. The buzzer also
starts sounding intermittently.
If this occurs, refill the fuel tank as soon as
possible.
The warning signals will be cleared when the
engine is restarted after the fuel tank is re-
filled.
NOTE:
Press any button on the multifunction informa-
tion center to stop the buzzer.
1Fuel level meter
1Hour meter/voltmeter
2“Volt/Hour” button
UF1X71E0.book Page 39 Tuesday, September 26, 2006 9:52 AM
Page 47 of 108
Features and functions
40
EJU35122Oil pressure warning indicator
If the oil pressure does not rise to specifica-
tion, the “WARNING” indicator light and the oil
pressure warning indicator begin to blink, and
the buzzer sounds intermittently. At the same
time, the engine speed is limited to help pre-
vent damage.
If this occurs, reduce the engine speed, return
to shore, and then check the engine oil level.
(See page 53 for engine oil level checking
procedures.) If the oil level is low, add enough
engine oil to raise it to the proper level. If the
oil level is sufficient, have a Yamaha dealer
check the watercraft.
NOTE:
Press any button on the multifunction informa-
tion center to stop the buzzer.
EJU36401Engine overheat warning indicator
This model is equipped with an engine over-
heat warning system.
If the engine starts to overheat, the engine
overheat warning system will be activated
and, in some cases, the warning system will
cut the ignition to the engine.
If the “WARNING” indicator light and the en-
gine overheat warning indicator begin to blink,
and the buzzer sounds intermittently, immedi-ately reduce the engine speed and return to
shore.
If the “WARNING” indicator light and the en-
gine overheat warning indicator come on, and
the buzzer sounds continuously, the warning
system will cut the ignition. The engine cannot
be started until it cools down, so it may be
necessary to have the watercraft towed back
to the shore. (See “Towing the watercraft” on
page 97 for towing procedures.)
After the engine cools down, start the engine,
and then check for water discharge at the port
(left) cooling water pilot outlet while the engine
is running. If there is no discharge of water,
shut the engine off, and then check the intake
grate and impeller for clogging.
WARNING
EWJ00050
Before attempting to remove weeds or de-
bris from the intake grate or impeller, shut
the engine off and remove the clip from the
UF1X71E0.book Page 40 Tuesday, September 26, 2006 9:52 AM
Page 48 of 108
Features and functions
41
engine shut-off switch. Severe injury or
death could result from coming in contact
with the rotating parts of the jet pump.
CAUTION:
ECJ00951
If you cannot locate and correct the cause
of the overheating, consult a Yamaha deal-
er. Continuing to operate at higher speeds
could result in severe engine damage.
NOTE:
Press any button on the multifunction informa-
tion center to stop the buzzer.
EJU36321Exhaust temperature warning indicator
This model is equipped with an exhaust tem-
perature warning system.
If the exhaust temperature becomes too hot,
the “WARNING” indicator light and the ex-haust temperature warning indicator begin to
blink, and the buzzer sounds intermittently.
If this occurs, reduce the engine speed and
return to shore to allow the exhaust system to
cool down.
CAUTION:
ECJ00960
This model is equipped with a catalytic
converter.
If the “WARNING” indicator light, exhaust
temperature warning indicator, and buzzer
come on, reduce the engine speed (below
6000 r/min), return to shore, and have a
Yamaha dealer check the watercraft.
NOTE:
Press any button on the multifunction informa-
tion center to stop the buzzer.
EJU35131Check engine warning indicator
If a sensor malfunction or a short circuit is de-
tected, the “WARNING” indicator light and the
UF1X71E0.book Page 41 Tuesday, September 26, 2006 9:52 AM
Page 49 of 108
Features and functions
42
check engine warning indicator begin to blink,
and the buzzer sounds intermittently.
If this occurs, reduce the engine speed, return
to shore, and have a Yamaha dealer check
the engine.
NOTE:
Press any button on the multifunction informa-
tion center to stop the buzzer.
EJU35033Right multifunction display and operation
buttons (for FX Cruiser High Output)
The right multifunction display shows the fol-
lowing information.
Compass
Average speed
Tripmeter
Trip timer
Fuel consumption per hour
Fuel consumption per kilometer/mile
Water temperature
Air temperatureThe following operation buttons are on the
right side of the multifunction information cen-
ter.
To switch the display mode, push the
“Mode/Reset” button for less than 1 second.
The display mode changes in the following or-
der.
Compass → Average speed → Tripmeter →
Trip timer → Fuel consumption per hour →
Fuel consumption per kilometer/mile → Water
temperature → Air temperature
NOTE:
To switch the display units between kilome-
ters/liters/degrees Celsius and miles/gal-
lons/degrees Fahrenheit, push the
“Volt/Hour” button for at least 1 second,
within 10 seconds after the multifunction in-
formation center starts operating.
The “SPEED” indicator light blinks three
times if miles/gallons/degrees Fahrenheit
are selected as the display units when the
multifunction information center starts oper-
1“Mode/Reset” button
2“Start/Stop” button
UF1X71E0.book Page 42 Tuesday, September 26, 2006 9:52 AM