warning YAMAHA FX SVHO 2022 User Guide

Equipment operation
71
when released. WARNING! Do not use the
reboarding step to lift the watercraft. The
reboarding step is not designed to support
the watercraft’s weight. If the reboarding
step breaks, the watercraft could fall,
which could result in severe injury.
[EWJ01212]
ECJ00743
Use the reboarding step only to board the
watercraft in the water. Do not use the re-
boarding step for any other purpose. The
watercraft can be damaged.
EJU34874Bow eye
The bow eye is used to attach a rope to the
watercraft when transporting, mooring, or
towing it in an emergency. (See page 122 for
information on towing the watercraft.)
EJU34883Stern eyes
The stern eyes are used to attach a rope to
the watercraft when transporting or mooring
it.
EJU40423Cleat
The cleat is used to attach a ski rope to the
watercraft when pulling a wakeboarder or
water-skier. WARNING! Do not use the
cleat to lift the watercraft. The cleat is not
designed to support the watercraft’s
weight. If the cleat breaks, the watercraft
could fall, which could result in severe in-
jury.
[EWJ01511]
1 Reboarding step
1
1Bow eye
1 Stern eye
1
11
UF3X73E0.book Page 71 Wednesday, October 6, 2021 9:04 AM

Equipment operation
72
EJU34894Pull-up cleats (FX LIMITED SVHO)
The pull-up cleats are used to attach a rope
to the watercraft when mooring it.
To use a pull-up cleat, pull it up. The pull-up
cleat returns automatically to its original posi-
tion when released. WARNING! Do not use
the pull-up cleats to lift the watercraft. The
pull-up cleats are not designed to support
the watercraft’s weight. If the pull-up
cleats break, the watercraft could fall,
which could result in severe injury.
[EWJ00822]
EJU46960
Dual Rope Hooks
The dual rope hooks are used to attach a
rope to the watercraft when transporting or
mooring it.
EJU35148Storage compartments
This watercraft is equipped with the following
storage compartments.
Only the securely closed watertight storage
compartment is waterproof. If you carry ob-
jects that must be kept dry, put them in a wa-
terproof bag.
Make sure that the storage compartments
are closed securely before operating the wa-
tercraft.
EJU45250Bow storage compartment
The bow storage compartment is located un-
der the hood.
To open the bow storage compartment:
Pull the hood latch rearward, and then lift up
the rear of the hood.
1 Cleat
1 Pull-up cleat
1
1
1Dual Rope Hooks
1 Hood latch
11
1
UF3X73E0.book Page 72 Wednesday, October 6, 2021 9:04 AM

Pre-operation checks
87
EJU40182Engine unit check
Check the exterior of the engine unit for dam-
age or other problem.
EJU36886Engine oil level check
Make sure that the engine oil level is between
the minimum and maximum level marks on
the dipstick. (See page 79 for information on
checking the engine oil level.)
EJU32456Bilge water check
Make sure that no bilge water has collected in
the engine compartment. If bilge water has
collected in the engine compartment, drain it.
(See page 81 for information on draining the
bilge water.)
EJU32488Battery checks
Make sure that the battery terminals are not
damaged and that the battery leads are con-
nected properly. WARNING! Never operate
the watercraft if the battery does not have
sufficient power to start the engine or if it
shows any other signs of decreased pow-
er. Loss of battery power may leave you
stranded.
[EWJ01242]
Make sure that the battery is securely held in
place.
1 Water separator
1 Dipstick
1
1
1Maximum level mark
2 Minimum level mark
1 Negative (–) battery terminal: Black lead
2 Positive (+) battery terminal: Red lead
1
2
12
UF3X73E0.book Page 87 Wednesday, October 6, 2021 9:04 AM

Pre-operation checks
89
EJU42181Throttle lever checks
Operate the throttle lever several times to
make sure that operation is smooth through-
out the whole range. Also, make sure that the
throttle lever returns automatically to its fully
closed (idle) position when released.
EJU45351Yamaha Security System checkMake sure that the Yamaha Security System
operates properly. (See page 24 for Yamaha
Security System setting procedures.)
EJU32666Engine shut-off cord (lanyard) check
Make sure that the engine shut-off cord (lan-
yard) is not damaged. If the cord is damaged,
replace it. WARNING! Never try to repair
the engine shut-off cord (lanyard) or tie it
together. The engine shut-off cord (lan-
yard) may not pull free when the operator
falls off, allowing the watercraft to conti-
nue to run and cause an accident.
[EWJ01222] EJU46050
Switch checksECJ01311
Do not run the engine over 4000 r/min on
land. Also, do not run the engine for more
than 15 seconds without supplying water,
otherwise the engine could overheat.
Check the engine start/stop switch and the
engine shut-off switch for proper operation.
(See page 24 for information on operating
each switch.)
1
Clip
2 Engine shut-off switch
3 Engine shut-off cord (lanyard)
12
3
UF3X73E0.book Page 89 Wednesday, October 6, 2021 9:04 AM

Pre-operation checks
92
EJU40147Post-launch checks
Perform the post-launch checks in the pre-
operation checklist while the watercraft is in
the water and the engine is running.
To perform the post-launch checks:
(1) Launch the watercraft. (See page 94 forinformation on launching the watercraft.)
(2) Perform the checks and make sure that there are no malfunctioning items or oth-
er problems.
EJU41811Cooling water pilot outlet check
Make sure that water is discharged from the
port (left) cooling water pilot outlet while the
engine is running. (See page 27 for informa-
tion on the cooling water pilot outlets.)
EJU47000Multifunction information center check
Make sure that the multifunction information
center operates properly. (See page 40 for in-
formation on proper operation of the multi-
function information center.)
EJU43393Shift system check
Operate the throttle lever and RiDE lever, and
check that the watercraft moves or does not
move according to the displayed shift indica-
tor. (See page 29 for shift system operation
procedures.) WARNING! To avoid colli-
sions, operate at safe speeds and keep a
safe distance away from people, objects,
and other watercraft.
[EWJ01860] EJU40172
Engine idling speed check
Start the engine and warm it up. Use the ta-
chometer in the multifunction information
center to make sure that the engine idling
speed is not significantly above or below the
specified range.
1
Shift indicator
2 “F” (Forward position)
3 “N” (Neutral position)
4 “R” (Reverse position)
Engine idling speed:
1250 ±100 r/min
MPH
RPM
x1000
12.7V10 :00AM
14
3
2
UF3X73E0.book Page 92 Wednesday, October 6, 2021 9:04 AM

Operation
94
EJU40212Riding position
Operator riding position
The operator should grip the handlebars firm-
ly with both hands and sit astride the seat
with both feet on the floor of the footwell.
Passenger riding position
The passenger(s) should hold on firmly, either
to the person in front of them or to the hand-
grip provided, and sit astride the seat with
their feet on the floor of the footwell. Never al-
low a passenger to ride in front of the opera-
tor. (See page 16 for information on the riding
position when pulling a wakeboarder or wa-
ter-skier.)
EJU32803Launching the watercraft
When launching the watercraft, make sure
that there are no obstacles around you.
If the watercraft is launched from a trailer,
someone should make sure that waves do
not push the watercraft into the trailer.
EJU46071Starting the engine on waterEWJ01532
Do not apply throttle when anyone is at the
rear of the watercraft. Turn the engine off
or keep it at idle. Water and debris exiting
the jet thrust nozzle can cause severe in-
jury.
To start the engine:
(1) If the lock mode is selected for theYamaha Security System setting, selectthe unlock mode. (See page 24 for
Yamaha Security System setting proce- dures.)
(2) Move the watercraft to an area that is free from weeds and debris, and has a
water depth of at least 60 cm (2 ft) from
the bottom of the watercraft. NOTICE:
Never run the engine in water that is
less than 60 cm (2 ft) deep from the
bottom of the watercraft, otherwise
pebbles or sand could be sucked into
the jet intake, causing impeller dam-
age and engine overheating.
[ECJ00473]
(3) Attach the engine shut-off cord (lanyard) to your left wrist, and then attach the clip
to the engine shut-off switch. (See page
25 for information on operating the en-
gine shut-off switch.) WARNING! Check
that the engine shut-off cord (lanyard)
UF3X73E0.book Page 94 Wednesday, October 6, 2021 9:04 AM

Operation
95
is attached correctly. If the engine
shut-off cord (lanyard) is not attached
correctly, it may not pull free when the
operator falls off, allowing the water-
craft to continue to run and cause an
accident.
[EWJ00583]
(4) With the throttle lever released, push theengine start/stop switch (red button) to
start the engine. (See page 24 for infor-
mation on operating the engine
start/stop switch.)
EJU46080Stopping the engine
Release the throttle lever, and then push the
engine start/stop switch (red button) to stop
the engine. WARNING! You need throttle to
steer. Shutting the engine off can cause
you to hit an obstacle you are attempting to avoid. A collision could result in severe
injury or death.
[EWJ00602]
EJU32874
Leaving the watercraft
If leaving the watercraft, remove the clip from
the engine shut-off switch to prevent acci-
dental starting or unauthorized operation by
children or others.
EJU43411Operating the watercraft
When the throttle lever is squeezed, the “F”
(forward) shift indicator will be displayed and
the watercraft will move forward. While the
“F” (forward) shift indicator is displayed, the
watercraft will move forward at trolling speed
even if the throttle lever is in the fully closed
(idle) position. (See page 29 for shift system
operation procedures.)
1 Clip
2 Engine shut-off switch
3 Engine shut-off cord (lanyard)
12
3
UF3X73E0.book Page 95 Wednesday, October 6, 2021 9:04 AM

Trouble recovery
118
Engine runs irregu-
larly or stallsFuel Fuel tank empty Refill as soon as pos-
sible77
Stale or contaminat-
ed Have serviced by
Yamaha dealer
—
Incorrect octane
number Use correct fuel
77
Fuel tank Water or dirt present Have serviced by Yamaha dealer—
Spark plug Fouled or defective Have serviced by Yamaha dealer—
Incorrect heat range Have serviced by Yamaha dealer —
Gap incorrect Have serviced by Yamaha dealer —
Electrical wir-
ing Loose connection Have serviced by
Yamaha dealer —
Fuel injec-
tion system Faulty or clogged in-
jectors Have serviced by
Yamaha dealer
—
Warning is dis-
played Fuel level
warningFuel tank empty Refill as soon as pos-
sible 77
Oil pressure
warning Oil pressure dropped Have serviced by
Yamaha dealer 65
Engine over-
heat warning Jet intake clogged Clean
120
Check en-
gine warning Faulty sensors Have serviced by
Yamaha dealer 64
TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF3X73E0.book Page 118 Wednesday, October 6, 2021 9:04 AM

Trouble recovery
119
Watercraft slow or
loses powerWatercraft
operation
modeDrive control mode
activated
Deactivate or adjust
drive control mode 36
Cavitation Jet intake clogged Clean 120 Impeller damaged or
worn Have serviced by
Yamaha dealer
120
Engine over-
heat warning Engine speed reduc-
tion control activated Clean jet intake and
cool engine
64
Oil pressure
warning Engine speed reduc-
tion control activated Add oil
65
Spark plug Fouled or defective Have serviced by Yamaha dealer—
Incorrect heat range Have serviced by Yamaha dealer —
Gap incorrect Have serviced by Yamaha dealer —
Electrical wir-
ing Loose connection Have serviced by
Yamaha dealer —
Fuel Stale or contaminat- ed Have serviced by
Yamaha dealer
—
Incorrect octane
number Use correct fuel
77
Air filter Clogged Have serviced by Yamaha dealer—
Oil buildup Have serviced by Yamaha dealer —
Throttle lever Faulty Have serviced by Yamaha dealer—
Audio system does
not activate
(equipped models) Fuse Burned out Have serviced by
Yamaha dealer —
TROUBLE POSSIBLE CAUSE REMEDY PAGE
UF3X73E0.book Page 119 Wednesday, October 6, 2021 9:04 AM

Index
125
I
Identification numbers ............................... 1
Information screen ................................... 52
J
Jet intake and impeller, cleaning ........... 120
Jet intake checks ..................................... 91
Jet thrust nozzle and reverse gate check .................................................... 91
Jumper cables, connecting.................... 121
L
Labels, important ....................................... 4
Labels, other .............................................. 8
Labels, warning .......................................... 5
Launching the watercraft ......................... 94
Learning to operate your watercraft ........ 93
Leaving the watercraft ............................. 95
Limitations on who may operate the watercraft................................................ 9
Long-term storage ................................. 108
Lubrication ............................................. 108
M
Main components, location of ................. 20
Maintenance .......................................... 110
Manufactured date label ............................ 2
Map display settings (“Chart Setup”)....... 62
Map screen .............................................. 45
Map settings ............................................ 52
Map settings (“Map Settings”) ................. 59
Media screen ........................................... 54
Model information ...................................... 3
Multifunction information center .............. 40
Multifunction information center check ... 92
N
Notification settings (“Notifications”) ....... 57
No-wake mode ........................................ 34
O
Operating in weeded areas .................... 103
Operating the watercraft .......................... 95
Operating the watercraft in reverse or neutral ................................................... 98
Operating your watercraft ........................ 93
Operation buttons .................................... 41
Operation requirements ........................... 11
P
Periodic maintenance chart ................... 112 Phone management
(“Phone Manager”) ............................... 57
Post-launch checks ................................. 92
Post-operation care ............................... 105
Pre-launch checks ................................... 86
Pre-operation check points...................... 86
Pre-operation checklist ............................ 84
Primary Identification (PRI-ID) number....... 1
Pull-up cleats (FX LIMITED SVHO)........... 72
R
Raising the reverse gate......................... 121
Reboarding grip ....................................... 70
Reboarding step....................................... 70
Recommended equipment ...................... 13
Regulatory informati on confirmation
(“Regulatory Info”) ................................ 63
Removable watertight storage
compartment ........................................ 75
Return to factory settings (“Factory Reset”)................................... 62
Reverse assist .......................................... 33
RiDE lever................................................. 26
RiDE lever checks .................................... 88
Riding position ......................................... 94
Rustproofing .......................................... 109
S
Safe boating rules .................................... 17
Safety equipment check .......................... 91
Satellite status confirmation (“Satellite Status”) ................................. 62
Seats ........................................................ 69
Selecting the display language ................ 55
Selecting the display units (“Unit”) ........... 55
Setting menu screen ................................ 54
Shift system ............................................. 29
Shift system check ................................... 92
Starting off ............................................. 101
Starting off from a trailer ........................ 102
Starting the engine on water .................... 94
Steering system ....................................... 26
Steering system checks ........................... 88
Stern drain plug checks ........................... 91
Stern eyes ................................................ 71
Stern storage compartment ..................... 74
Stopping the engine ................................. 95
UF3X73E0.book Page 125 Wednesday, October 6, 2021 9:04 AM