stop start YAMAHA FZR 2009 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2009, Model line: FZR, Model: YAMAHA FZR 2009Pages: 96, PDF Size: 7.01 MB
Page 6 of 96
Table of contents
General and important labels ........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Craft Identification Number (CIN) ...... 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 8
Safety information ........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 12
Recommended equipment ........... 14
Hazard information ....................... 15
Watercraft characteristics ............. 15
Safe boating rules ........................ 17
Enjoy your watercraft
responsibly ................................ 17
Features and functions ................... 19
Location of main components ...... 19
Operation of controls and other
functions .................................... 23
Seats ............................................... 23
Hood ................................................ 24
Fuel tank filler cap ........................... 24
Remote control transmitter .............. 24
Engine stop switch .......................... 25
Engine shut-off switch ..................... 25
Start switch ...................................... 26
Throttle lever ................................... 26
Cooling water pilot outlets ............... 27
Steering system ............................... 27
Telescopic steering system ............. 28
Shift lever ........................................ 28
Quick Shift Trim System (QSTS)
selector ........................................ 29
Reboarding grip ............................... 30Bow eye ........................................... 30
Stern eyes ....................................... 31
Yamaha Security System ................ 31
Dual analog meter unit .................... 33
Storage compartments .................... 37
Operation ......................................... 41
Fuel and oil .................................. 41
Fuel ................................................. 41
Engine oil ......................................... 42
Pre-operation checks ................... 43
Pre-operation check list ................... 43
Pre-operation check points .............. 45
Operation ..................................... 53
Engine break-in ............................... 53
Launching the watercraft ................. 53
Starting the engine .......................... 53
Stopping the engine ........................ 54
Shifting ............................................ 55
Leaving the watercraft ..................... 55
Operating your watercraft ............ 56
Getting to know your watercraft ....... 56
Learning to operate your
watercraft ..................................... 56
Riding with a passenger .................. 57
Starting the watercraft ..................... 57
Boarding and starting in deep
water ............................................ 58
Capsized watercraft ......................... 61
Turning the watercraft ..................... 62
Stopping the watercraft ................... 63
Beaching the watercraft ................... 64
Docking the watercraft ..................... 64
Reverse on waterways .................... 64
Operating in weeded areas ............. 64
Post-operation care ...................... 65
Transporting ................................. 66
Maintenance and care .................... 67
Storage ........................................ 67
Flushing the cooling system ............ 67
Lubrication ....................................... 68
Battery ............................................. 68
Cleaning the watercraft ................... 68
UF2R70E0.book Page 1 Thursday, November 6, 2008 10:05 AM
Page 22 of 96
Safety information
15
EJU36850
Hazard information
Never start the engine or let it run for any
length of time in an enclosed area. Exhaust
fumes contain carbon monoxide, a color-
less, odorless gas that may cause loss of
consciousness and death within a short
time. Always operate the watercraft in an
open area.
Do not touch the hot muffler or engine dur-
ing or immediately after engine operation;
they can cause serious burns.
EJU30920
Watercraft characteristics
Jet thrust turns the watercraft. Releasing
the throttle lever completely produces only
minimum thrust. If you are traveling at
speeds above trolling, you will have rapidly
decreasing ability to steer without throttle.
This model is equipped with the Yamaha
Engine Management System (YEMS) that
includes an off-throttle steering (OTS) sys-
tem. It will activate at planing speeds should
you attempt to steer the watercraft after re-
leasing the throttle lever. The OTS system
assists in turning by continuing to supply
some thrust while the watercraft is deceler-
ating, but you can turn more sharply if you
apply throttle while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar
input until you apply throttle again or you
reach trolling speed.
Practice turning in an open area without ob-
stacles until you have a good feel for this
maneuver.
This watercraft is water-jet propelled. The
jet pump is directly connected to the engine.
This means that jet thrust will produce some
movement whenever the engine is running.
There is no “neutral” position. You are in ei-
ther “forward” or “reverse”, depending upon
the shift lever position.
Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or im-
pact the handlebars.
This could increase the risk of back/spinal
injury (paralysis), facial injuries, and broken
legs, ankles, and other bones. You could
also damage the shift mechanism.
UF2R70E0.book Page 15 Thursday, November 6, 2008 10:05 AM
Page 28 of 96
Features and functions
21
Control system
1234
6
7 5
10
11121314 9 8
1Quick Shift Trim System (QSTS) selector
2QSTS selector lock lever
3Start switch
4Engine shut-off switch
5Clip
6Engine stop switch
7Engine shut-off cord (lanyard)
8Dual analog meter unit
9Rearview mirrors
10Glove compartment
11Remote control transmitter
12Beverage holder
13Shift lever
14Throttle lever
UF2R70E0.book Page 21 Thursday, November 6, 2008 10:05 AM
Page 34 of 96
Features and functions
27
EJU36740Cooling water pilot outlets
This watercraft is equipped with cooling water
pilot outlets on the port (left) and starboard
(right) sides of the watercraft.
When the engine is running, cooling water is
circulated in the engine, and then it is dis-
charged from the pilot outlets.
To check for proper operation of the cooling
system, check that water is being discharged
from the port (left) pilot outlets. If water is not
being discharged from these outlets, cooling
water may not be circulating in the engine.
When this occurs, stop the engine and check
for the cause. (See pages 36 and 83 for more
information.)
TIP:
If the cooling water passages are dry, it will
take about 60 seconds for the water to
reach the outlets after the engine is started.
Water discharge may not be constant at
idle, therefore, open the throttle a little to
check that water discharges properly.
EJU31260Steering system
Your watercraft can be steered by turning the
handlebars in the direction you wish to travel.
When the handlebars are turned, the angle of
the jet thrust nozzle is changed, and the direc-
tion of the watercraft is changed accordingly.
Since the strength of the jet thrust determines
the speed and degree of a turn, throttle must
always be applied when attempting a turn, ex-
cept at trolling speed.
This model is equipped with the Yamaha En-
gine Management System (YEMS) that in-
cludes an off-throttle steering (OTS) system.
It will activate at planing speeds should you
attempt to steer the watercraft after releasing
the throttle lever. The OTS system assists in
turning by continuing to supply some thrust
while the watercraft is decelerating, but you
can turn more sharply if you apply throttle
while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
1Handlebar
2Jet thrust nozzle
1
2
UF2R70E0.book Page 27 Thursday, November 6, 2008 10:05 AM
Page 38 of 96
Features and functions
31
EJU34880Stern eyes
The stern eyes are located at the stern of the
watercraft.
The stern eyes are used to attach a rope to
the watercraft when transporting or mooring it.
EJU37400Yamaha Security System
The Yamaha Security System functions to
help prevent unauthorized use or theft of the
watercraft. The lock and unlock modes of the
security system are selected using the remote
control transmitter that is included with this
watercraft. The engine cannot be started if the
security system is in the lock mode. The en-
gine can only be started in the unlock mode.
(See page 24 for information on using the re-
mote control transmitter.)
TIP:
The lock and unlock modes of this system can
only be selected while the engine is stopped.
EJU37410Yamaha Security System settings
The Yamaha Security System settings will be
confirmed by the number of beeps when the
remote control transmitter is operated, and by
the “UNLOCK” indicator light of the dual ana-
log meter unit. (See page 33 for more infor-
mation on the dual analog meter unit.)
TIP:
The beeper sounds two times for the nor-
mal operation mode or three times for the L-
MODE (low-RPM mode). (See page 32 for
L-MODE selection procedures.)
If the remote control transmitter is operated
while the dual analog meter unit is in the
standby state, the unit will perform the initial
operation, and then the setting is selected.
To select the lock mode:
Press the lock button on the remote control
transmitter briefly. The beeper sounds once
and the “UNLOCK” indicator light blinks once,
then goes off. This indicates the lock mode is
selected.
To select the unlock mode:
Press the “L-Mode” (unlock) button on the re-
mote control transmitter briefly. The beeper
sounds two or three times and the “UNLOCK”
indicator light blinks two or three times, then
1Stern eye
1
Number of
beepsYa m a h a S e c u r i t y
System mode“UN-
LOCK” in-
dicator
light
Lock Goes off
Unlock
(normal operation
mode)Comes
on
Unlock
(L-MODE)Comes
on
1Lock button
2“UNLOCK” indicator light
2
1
UF2R70E0.book Page 31 Thursday, November 6, 2008 10:05 AM
Page 39 of 96
Features and functions
32
comes on. This indicates the unlock mode is
selected.
EJU37420L-MODE (low-RPM mode)
The L-MODE limits the engine speed to ap-
proximately 70% of the maximum engine
speed.
The L-MODE activation and deactivation can
only be selected using the remote control
transmitter. (See page 24 for information on
using the remote control transmitter.)
TIP:
The L-MODE can only be selected when the
engine is stopped in the unlock mode of the
Yamaha Security System.
Activating and deactivating the L-MODE
Activation of the L-MODE will be confirmed by
the number of beeps when the remote control
transmitter is operated, and by the “L-MODE”indicator light of the dual analog meter unit.
(See page 33 for more information on the dual
analog meter unit.)
TIP:
If the remote control transmitter is operated
while the dual analog meter unit is in the
standby state, the unit performs the initial op-
eration, and then the setting is selected.
To activate the L-MODE:
Press the “L-Mode” (unlock) button on the re-
mote control transmitter for more than 4 sec-
onds. Once the beeper sounds three times
and the “UNLOCK” indicator light blinks three
times, then comes on, the “L-MODE” indicator
light comes on and the L-MODE is activated.
TIP:
If the L-MODE is selected immediately after
the information display turns off, the “L-
MODE” indicator light will not come on. The
“L-MODE” indicator light will come on when
the engine is started.
1“L-Mode” (unlock) button
2“UNLOCK” indicator light
1Remote control transmitter
2
1
Number of
beepsL-MODE operation“L-
MODE”
indicator
light
ActivatedComes
on
Deactivated Goes off
1“L-Mode” (unlock) button
2“L-MODE” indicator light
2
1
UF2R70E0.book Page 32 Thursday, November 6, 2008 10:05 AM
Page 40 of 96
Features and functions
33
To deactivate the L-MODE:
Press the “L-Mode” (unlock) button on the re-
mote control transmitter for more than 4 sec-
onds. Once the beeper sounds two times and
the “UNLOCK” indicator light blinks two times,
then comes on, the “L-MODE” indicator light
goes off and the L-MODE is deactivated.
When the L-MODE is deactivated, the water-
craft returns to the normal operation mode.
EJU37431Dual analog meter unit
The dual analog meter unit displays various
watercraft information.
Dual analog meter unit initial operation
When the dual analog meter unit starts oper-
ating, the speedometer and tachometer make
one sweep, all segments of the information
display and all indicator lights come on. After
2 seconds, the “WARNING” indicator light, the
“L-MODE” indicator light, and the warning in-
dicators in the information display go off, and
then the unit starts to operate normally.
TIP:
The “UNLOCK” indicator light will go off when
the engine is started.Dual analog meter unit standby state
If the dual analog meter unit does not receive
any operation input within 25 seconds after
the engine stops, the unit will turn off and en-
ter a standby state. When the engine is start-
ed again, the display and the indicator lights
will return to their state before the unit turned
off, and then the unit starts to operate normal-
ly.
EJU37440Speedometer
The speedometer shows the watercraft speed
against water.
The large inner numbers on the meter show
the watercraft speed in miles per hour “MPH”
and the small outer numbers show the speed
in kilometers per hour “km/h”.
EJU37240Tachometer
The tachometer shows the engine speed.
The large inner numbers on the meter show
the engine speed × 1000 RPM (r/min).
1Speedometer
2Information display
3Tachometer
4“Hour Volt” button
5“UNLOCK” indicator light
6“L-MODE” indicator light
7“WARNING” indicator light
123
7 6 5 4
UF2R70E0.book Page 33 Thursday, November 6, 2008 10:05 AM
Page 42 of 96
Features and functions
35
To switch to the voltmeter from the hour
meter:
Push the “Hour Volt” button for at least 1 sec-
ond. The display switches from the hour
meter to the voltmeter.
EJU37270Fuel level meter
The fuel level meter is provided for convenient
fuel level checking while riding.
The fuel level meter has four segments which
show the amount of fuel remaining in the fuel
tank. The display segments of the fuel level
meter disappear one at a time as the fuel level
decreases.
TIP:
The fuel level is most accurate when the wa-
tercraft is sitting level on a trailer or in the wa-
ter.
EJU37280Fuel level warning
If the fuel remaining in the fuel tank drops to
about 18 L (4.8 US gal, 4.0 Imp. gal), the low-
est fuel level segment, the fuel indicator, and
the “WARNING” indicator light blink, and the
buzzer sounds intermittently.
If this occurs, refill the fuel tank as soon as
possible.
The warning signals will be cleared when the
engine is restarted after the fuel tank is re-
filled.
TIP:
Push the “Hour Volt” button to stop the buzz-
er.
EJU37290Oil pressure warning
If the oil pressure drops significantly, the
“WARNING” indicator light and the oil pres-
sure warning indicator blink, and the buzzer
sounds intermittently. At the same time, the
1“Hour Volt” button
2Vo l t m e t e r
1Fuel level meter
1
2
1
1“Hour Volt” button
1
UF2R70E0.book Page 35 Thursday, November 6, 2008 10:05 AM
Page 43 of 96
Features and functions
36
maximum engine speed is limited to help pre-
vent damage.
If this occurs, immediately reduce the engine
speed, return to shore, and then check the en-
gine oil level. (See page 45 for engine oil level
checking procedures.) If the oil level is suffi-
cient, have a Yamaha dealer check the water-
craft.
TIP:
Push the “Hour Volt” button to stop the buzz-
er.
EJU37300Engine overheat warning
If the engine temperature rises significantly,
the “WARNING” indicator light and the engine
overheat warning indicator blink, and the
buzzer sounds intermittently. Then, the
“WARNING” indicator light and the engine
overheat warning indicator stop blinking and
remain on, and the buzzer sounds continu-ously. After the light and indicator start to blink
and the buzzer sounds, the maximum engine
speed is limited to help prevent damage.
If this occurs, immediately reduce the engine
speed, return to shore, and then check for wa-
ter discharge at the port (left) cooling water pi-
lot outlets while the engine is running. If there
is no discharge of water, shut the engine off,
and then check the jet intake for clogging.
(See page 83 for jet intake cleaning proce-
dures.) NOTICE: If you cannot locate and
correct the cause of the overheating, con-
sult a Yamaha dealer. Continuing to oper-
ate at higher speeds could result in severe
engine damage.
[ECJ00041]
1“Hour Volt” button
1
UF2R70E0.book Page 36 Thursday, November 6, 2008 10:05 AM
Page 50 of 96
Operation
43
EJU31980
Pre-operation checks EJU31991Pre-operation check list
Before operating this watercraft, perform the checks in the following check list.
WARNING
EWJ00411
Failure to inspect or maintain the watercraft properly increases the possibility of an ac-
cident or damage to the watercraft. Do not operate the watercraft if you find any prob-
lem. If a problem cannot be corrected by the procedures provided in this manual, have
the watercraft inspected by a Yamaha dealer.
ITEM ROUTINE PAGE
BEFORE LAUNCH OR OPERATION
Engine compartmentRemove the seats to ventilate the engine compart-
ment. Check for fuel vapors and loose electrical con-
nections.45
BilgeCheck for water and fuel and drain if necessary. 47
Stern drain plugsCheck for proper installation. 47
Throttle leverCheck that the throttle lever springs back smoothly. 48
Steering systemCheck for proper operation.
Check that the handlebars are locked in place.49
Shift lever and reverse gateCheck for proper operation. 49
QSTSCheck for proper operation. 50
Fuel and oilCheck the fuel and oil levels and replenish if neces-
sary.
Check the hoses and tanks for leakage.45, 45
Water separatorCheck for water and drain if necessary. 46
BatteryCheck the electrolyte level and battery condition. 47
HoodCheck that the hood is securely closed. 24
Front and rear seatsCheck that the seats are securely installed. 23
Hull and deckCheck the hull and deck for cracks and other dam-
age.45
Jet intakeCheck for debris and remove if necessary. 51
Fire extinguisherCheck the condition and replace if necessary. 48
Engine shut-off cord (lan-
yard)Check the condition and replace if frayed or broken. 51
SwitchesCheck the start switch, engine stop switch, and en-
gine shut-off switch for proper operation.51
AFTER LAUNCH
Cooling water pilot outletCheck that water is discharged while the engine is
running and the watercraft is in the water.52
Dual analog meter unitCheck for warning indications and proper operation. 52
UF2R70E0.book Page 43 Thursday, November 6, 2008 10:05 AM