start stop button YAMAHA GP1300R 2005 Owners Manual

2-7
E
EJU10150
Engine stop switch
Push this switch 1 (red button) to stop
the engine normally.
EJU10160
Engine shut-off switch
Insert the clip 1, on the end of the engine
shut-off cord 2, under the engine shut-off
switch 3 (black button). The engine will stop
automatically when the clip is removed from
the switch, such as if the operator falls off
the watercraft.
WARNING@
Always attach the engine shut-off cord
to your wrist and the clip to the engine
shut-off switch BEFORE starting the
engine.

To prevent accidental starting of the
engine or unauthorized use by chil-
dren or others, always remove the clip
from the shut-off switch when the
engine is not running.
@
EJU10180
Throttle lever
Squeeze the throttle lever 1 to increase
engine speed.
Release the throttle lever to decrease
engine speed or to return it to the idle posi-
tion.
UF1G72.book Page 7 Thursday, September 30, 2004 2:28 PM

2-8
E
EJU18610
Start switch
Push the start switch 1 (green button) to
start the engine.
NOTE:@ The engine will not start when the clip is
removed from the engine shut-off switch or if
the throttle lever is squeezed.
@
EJU10201
Cooling water pilot outlet
This watercraft is equipped with cooling
water pilot outlets.
When the engine is running, cooling
water is circulated in the engine, and then it
is discharged from the pilot outlets.
To check for proper operation of the cool-
ing system, check that water is being dis-
charged from the pilot outlets. If water is not
being discharged from the outlets, cooling
water may not be circulating in the engine.
When this occurs, stop the engine and
check for the cause. (See pages 2-12 and
5-4 for further instructions.)
NOTE:@ If the cooling water passages are dry, it will
take about 20 seconds for the water to reach
the outlet after the engine is started.
@
UF1G72.book Page 8 Thursday, September 30, 2004 2:28 PM

2-13
E
If the overheat warning is ignored, engine
and exhaust system heat may increase, par-
ticularly if the watercraft is operated at
higher speeds. When this occurs, the warn-
ing light, the engine overheat warning indi-
cator and the buzzer will change from
intermittently to continuously on, and the
overheat system will stop ignition to the
engine to reduce the risk of severe over-
heating. The engine cannot be started until
it cools down, so it may be necessary to
have the watercraft towed back to the
beach. (See “Towing the watercraft” on page
5-7 for towing procedures.)
NOTE:@ Press the select button on the multifunction
information center to stop the buzzer.
@
EJU20460
Exhaust temperature warning
system
This model is equipped with an exhaust
temperature warning system.
If the exhaust temperature gets too hot,
the warning light and exhaust temperature
warning indicator begin to blink, and the
buzzer sounds intermittently.
When this occurs, reduce engine speed
and beach the watercraft to allow the
exhaust system to cool down.
WARNING@ Hot muffler surfaces can cause serious
burns. Do not touch any muffler surface
during or after engine operation. The cat-
alytic converter gets hotter after the
engine stops.
@
UF1G72.book Page 13 Thursday, September 30, 2004 2:28 PM

2-15
E
EJU20161
Multifunction information
center
This meter contains following functions for
the help and convenience of operation.
1
Tachometer
2
Speedometer
3
Hour meter/Voltmeter
4
Fuel meter
5
Warning light
6
Fuel warning indicator
7
Engine overheat warning indicator
8
Oil warning indicator
9
Exhaust temperature warning indicator
0
Check engine warning indicator
A
Select button
CAUTION:@
Do not run the engine over 4,000 r/min
to check the meter for operation on
land. The engine could overheat or the
catalytic converter could result in seri-
ous damage.

Use the specified resistor-type spark
plug and cap, otherwise the meter may
function erratically.
@
NOTE:@ All display light up and the buzzer sounds
twice after the engine starts. Then, the
meter will operate normally after few sec-
onds. The current display will continue to
operate for 25 seconds after the engine
stops.
@
UF1G72.book Page 15 Thursday, September 30, 2004 2:28 PM

3-19
E
2. Attach the clip 1 to the engine shut-off
switch 2. Also, attach the engine shut-
off cord 3 to your left wrist.
WARNING@ Check that the engine shut-off cord is not
frayed or broken, and keep it free from
the handlebars so the engine stops if the
operator falls off. The engine shut-off
cord may not pull free if wrapped around
the handlebars when the operator falls
off, allowing the watercraft to continue to
run and cause an accident.
@
NOTE:@ It is not possible to start the engine with the
clip removed from the engine shut-off
switch.
@
3. Push the start switch (green button).
NOTE:@ The engine will not start if the throttle lever is
squeezed.
@
4. Release the start switch as soon as the
engine starts to run.
CAUTION:@
Never push the start switch while the
engine is running.

Do not operate the start switch for
more than 5 seconds, otherwise the
battery will be discharged and the
engine will not start. Also, the starter
motor may be damaged. If the engine
does not start in 5 seconds, release
the start switch, wait 15 seconds, and
then try again.
@
UF1G72.book Page 19 Thursday, September 30, 2004 2:28 PM

3-20
E
EJU10660
Stopping the engine
To stop the engine, release the throttle
lever, and then push the engine stop switch
(red button).
WARNING@ You need throttle to steer. Shutting off
the engine can cause you to hit an obsta-
cle you are attempting to avoid. A colli-
sion could result in severe injury or
death.
@
EJU10670
Leaving the watercraft
If leaving the watercraft, remove the
engine shut-off cord to reduce the chance of
accidental starting or unauthorized use by
children or others.
UF1G72.book Page 20 Thursday, September 30, 2004 2:28 PM