cooling YAMAHA GP1300R 2006 User Guide

4-1
E
EJU18121
Storage
WARNING@ Always place the watercraft upright in a
horizontal position when storing it, oth-
erwise fuel could leak out into the engine
or engine compartment, which could
result in a fire hazard.
@
Storage for prolonged periods of time,
such as winter storage, requires preventa-
tive maintenance to ensure against deterio-
ration. It is advisable to have the watercraft
serviced by a Yamaha dealer prior to stor-
age. However, the following procedures can
be performed by the owner.
EJU11942
Flushing the cooling system
Flushing the cooling system is essential
to prevent the cooling system from being
clogged with salt, sand, or dirt.
WARNING@ Stay away from stern when engine is run-
ning on land. Hot water and steam spurt-
ing from exhaust outlet into the air can
cause serious burns.
@
CAUTION:@
Do not supply water to the cooling
water passages when the engine is not
running. The water could flow back
through the muffler into the crankcase
causing severe engine damage.

Do not run the engine of the watercraft
for more than 15 seconds without sup-
plying water, otherwise the engine may
overheat.

Do not run engine over 4,000 r/min on
land. The catalytic converter could
sustain serious damage.
@
UF1G73.book Page 1 Tuesday, July 12, 2005 8:55 AM

4-2
E
1. Put the watercraft on land in a horizontal
position.
2. Open the flushing hose connector
cap1, and then insert the garden hose
adapter 2 into the flushing hose con-
nector 3 and turn it until it is securely
connected.
3. Connect the garden hose adapter to a
water tap using a hose.
NOTE:@ The garden hose is not included and must
be purchased separately.
@
4. Start the engine, and then immediately
turn the water supply on until water flows
out continually from the cooling water
pilot outlet.
5. Run the engine at idling speed for about
3 minutes watching the engine condition.
If the engine stops while flushing, turn
the water supply off immediately and
repeat the above steps.
6. Turn the water supply off, and then force
the remaining water out from the cooling
passages by running the engine at
4,000 r/min or less within 10 to 15 sec-
onds.
7. Stop the engine.
8. Remove the garden hose adapter and
secure the cap.
UF1G73.book Page 2 Tuesday, July 12, 2005 8:55 AM

4-10
E
EJU13550
Periodic maintenance chart
The following chart gives general guidelines for periodic maintenance. However, depend-
ing on your operating conditions maintenance may need to be performed more frequently.
PMC-*** (
) This mark indicates maintenance that you may do yourself.
(
❍) This mark indicates work to be done by a Yamaha dealer.
MAINTENANCE INTERVAL
INITIALTHEREAFTER
EVERYPA G E
10
hours50
hours100
hours100
hours200
hours
ITEM
6
months12
months12
months24
months
Spark plug Inspect, clean, adjust




4-14
Lubrication points Lubricate


4-16
Intermediate housing Lubricate❍
*1

*2

*2 4-17
Fuel system Inspect❍❍
4-11
Fuel tank Inspect, clean❍❍
4-11
Oil injection system Inspect, clean❍❍
4-12
Throttle shaft Inspect❍❍
—
Cooling water passages Flush

*3 4-1
Water inlet strainer Inspect, clean❍❍
—
Bilge strainer Clean❍❍
—
Electric bilge pump strainer Inspect, clean❍❍
—
Impeller Inspect❍❍
—
Jet thrust nozzle angle Inspect, adjust

/❍

/❍
4-13
QSTS mechanism Inspect, adjust❍❍❍
—
Throttle cable Inspect, adjust❍❍❍
4-13
Stern drain plugs Inspect, replace❍❍
3-9
Battery Inspect ❍❍
4-18
Rubber coupling Inspect❍
—
Engine mount Inspect❍
—
Nuts and bolts Inspect❍❍❍
—
*1: Grease quantity: 33.0–35.0 cm3 (1.11–1.18 oz)
*2: Grease quantity: 6.0–8.0 cm3 (0.20–0.27 oz)
*3: After every use
UF1G73.book Page 10 Tuesday, July 12, 2005 8:55 AM

4-23
E
EJU13590
Specifications
SPC-*** MODEL
ITEMUnit GP1300R
WATERCRAFT CAPACITY
Maximum people on board Number of people 2
Maximum load capacity kg (lb) 160 (353)
DIMENSIONS
Length mm (in) 2,930 (115.4)
Width mm (in) 1,150 (45.3)
Height mm (in) 1,020 (40.2)
Dry weight kg (lb) 297 (655)
PERFORMANCE
Maximum output kW (PS) @ r/min 125.0 (170) @ 7,000
Maximum fuel consumption L/h (US gal/h, Imp gal/h) 57.0 (15.1, 12.5)
Cruising range at full throttle hr. 1.05
Trolling speed r/min 1,250–1,450
ENGINE
Engine type 2-stroke
Number of cylinders 3
Engine displacement
cm
3 (cu in)1,297 (79.1)
Bore & stroke mm (in) 84 ×
78 (3.31 ×
3.07)
Compression ratio 5.9:1
Lubrication system Variable oil injection
Cooling system Water cooled
Starting system Electric starter
Ignition system Digital CDI
Spark plug BR8ES-11 (NGK)
Spark plug gap mm (in) 1.0–1.1 (0.039–0.043)
Battery capacity V-AH 12-19
Charging system Flywheel magneto
DRIVE UNIT
Propulsion system Jet pump
Jet pump type Axial flow, single stage
Impeller rotation Counterclockwise (viewed from rear)
Transmission Direct drive from engine
Jet thrust nozzle angle Degree 23 + 23
Trim nozzle angle Degree -10, -5, 0, 5, 10
FUEL AND OIL
Recommended fuel Regular unleaded gasoline
Minimum octane rating PON
RON86
90
Recommended engine oil YAMALUBE 2-W only
Fuel tank capacity
Total L (US gal, Imp gal) 60 (15.9, 13.2)
Oil tank capacity L (US gal, Imp gal) 5.5 (1.5, 1.2)
UF1G73.book Page 23 Tuesday, July 12, 2005 8:55 AM

6-1
E
EJU11250
Index
2-stroke engine oil ................................... 3-3
A
Adjusting the fuel injection system ........ 4-20
Adjusting the Yamaha Adjustable
Sponson (YAS) ..................................... 4-22
B
Battery ............................................ 3-10, 4-5
Beaching the watercraft ........................ 3-32
Bilge ........................................................ 3-9
Bleeding the oil injection pump ............. 4-21
Boarding alone ...................................... 3-25
Boarding and starting in deep water ..... 3-25
Boarding with a passenger.................... 3-26
Bow down.............................................. 2-11
Bow up .................................................. 2-11
Builder’s plate.......................................... 1-2
C
Capsized watercraft .............................. 3-27
Check engine warning indicator ............ 2-18
Checking the trolling speed ................... 4-20
Cleaning and adjusting the
spark plugs ............................................ 4-14
Cleaning the jet intake and impeller ........ 5-4
Cleaning the watercraft ........................... 4-6
Connecting the jumper cables................. 5-7
Cooling water pilot outlet ................ 2-8, 3-15
Cruising limitations ................................ 1-10
D
Docking the watercraft .......................... 3-32
E
Emergency procedures ........................... 5-4
Engine break-in ..................................... 3-16
Engine compartment ............................... 3-7
Engine overheat warning indicator ........ 2-19
Engine overheat warning system .......... 2-12
Engine serial number .............................. 1-1
Engine shut-off cord (lanyard) ............... 3-14
Engine shut-off switch ............................. 2-7
Engine stop switch .................................. 2-7Enjoy your watercraft responsibly ......... 1-16
Exhaust temperature warning
indicator................................................. 2-19
Exhaust temperature warning
system ................................................... 2-13
F
Filling the fuel tank .................................. 3-4
Filling the oil tank .................................... 3-5
Fire extinguisher .................................... 3-11
Flushing the cooling system .................... 4-1
Front storage compartment ................... 2-20
Fuel and oil.............................................. 3-1
Fuel and oil systems ............................... 3-8
Fuel meter ............................................. 2-16
Fuel system ............................................. 4-3
Fuel tank ............................................... 4-11
Fuel tank filler cap ................................... 2-6
Fuel warning indicator ........................... 2-17
G
Gasohol ................................................... 3-3
Gasoline .................................................. 3-1
Getting to know your watercraft ............ 3-21
Glove compartment ............................... 2-21
H
Handgrip ................................................ 2-11
Hazard information ................................ 1-14
Hood........................................................ 2-6
Hour meter/Voltmeter ............................ 2-17
Hull and deck .......................................... 3-7
Hull Identification Number (HIN).............. 1-1
I
Identification numbers ............................. 1-1
Important labels ....................................... 1-3
Inspecting and adjusting the
throttle cable.......................................... 4-13
Inspecting the battery ............................ 4-18
Inspecting the fuel system ..................... 4-11
Inspecting the jet thrust nozzle angle .... 4-13
Inspecting the oil injection system ......... 4-12
J
Jet unit................................................... 3-14
Jumping the battery ................................. 5-6
UF1G73.book Page 1 Tuesday, July 12, 2005 8:55 AM