remove YAMAHA GRIZZLY 125 2004 Manuale de Empleo (in Spanish)

1-1
EBU00464
LOCATION OF THE WARNING
AND SPECIFICATION LABELS
Read and understand all of the labels on your
machine. They contain important information for
safe and proper operation of your ATV.
Never remove any labels from your ATV. If a
label becomes difficult to read or comes off, a
replacement label is available from your
Yamaha dealer.
45 2
3
11
9
7
q
0
86
1For Oceania
Pour l’Océania
Para Oceaníasit here. NEVER3MX-24875-A0
2
5kg11lbs3LD-24877-A0
3
10kg22lbs1C5-24877-A0
1C5-9-60-01 11/12/03 7:26 PM Page 24

4-1
EBU00040
CONTROL FUNCTIONS
EBU09420
Main switch
Functions of the respective switch positions are
as follows:
ON:
The engine can be started only at this position
and the headlights and taillight come on when
the light switch is on.
OFF:
All electrical circuits are switched off. The key
can be removed in this position.
OFF ON
1C5-9-60-04 11/12/03 7:26 PM Page 2

4-9
cC
Do not use the headlights with the engine
turned off for an extended period of time,
otherwise the battery may discharge to the
point that the starter motor will not operate
properly. If this should happen, remove the
battery and recharge it.
EBU00590
Horn switch “*”
Press the switch to sound the horn.
1
1. Horn switch
1C5-9-60-04 11/12/03 7:26 PM Page 10

4-11
EBU00063
Throttle lever
Once the engine is running, movement of the
throttle lever will increase the engine speed.
Regulate the speed of the machine by varying
the throttle position. Because the throttle is
spring-loaded, the machine will decelerate, and
the engine will return to an idle any time the
hand is removed from the throttle lever.
Before starting the engine, check the throttle to
be sure it is operating smoothly. Make sure it
returns to the idle position as soon as the lever
is released.
w
Malfunction of the throttle could make it diffi-
cult to speed up or slow down when you
need to. This could cause an accident.
Check the operation of the throttle lever
before you start the engine. If the throttle
does not work smoothly, check for the
cause. Correct the problem before riding the
ATV or consult a Yamaha dealer.
q
1. Throttle lever1. Levier d’accélérateur1. Palanca del aceleración
1C5-9-60-04 11/12/03 7:26 PM Page 12

4-19
EBU11060
Drive select lever
The drive select lever is used to shift your
machine into the forward, neutral and reverse
positions. (Refer to page 6-13 for the drive
select lever operation.)
EBU00092
Fuel tank cap
Remove the fuel tank cap by turning it counter-
clockwise.
1
2
a
3
1
a. Drive select lever 1. Neutral
2. Forward 3. Reverse
a. Levier de présélection 1. Point mort
2. Avant 3. Arrière
a. Palanca de selección de gama 1.Punto muerto
2. Adelante 3. Atrás
1. Fuel tank cap1. Bouchon de réservoir de carburant1. Tapón del depósito de combustible
1C5-9-60-04 11/12/03 7:26 PM Page 20

4-25
EBU00567
Seat
To remove the seat, pull the seat lock lever
upward and pull up the seat at the rear.
To install the seat, insert the projections on the
front of the seat into the seat holders and push
down on the seat at the rear.
NOTE:
Make sure that the seat is securely fitted.
q
1. Seat lock lever1. Levier de verrouillage de la selle1. Palanca de bloqueo del sillín
1C5-9-60-04 11/12/03 7:26 PM Page 26

7-21
During operation
Always keep your feet on the footboards during
operation. Otherwise your feet may contact the
rear wheels.
w
Always keep both hands on the handlebars
and both feet on the footboards of your ATV
during operation. Removing even one hand
or foot can reduce your ability to control the
ATV or could cause you to lose your balance
and fall off of the ATV. If you remove a foot
from a footboard, your foot or leg may come
into contact with the rear wheels, which
could injure you or cause an accident.
1C5-9-60-07 11/12/03 7:24 PM Page 22

8-13
EBU14900
Engine oil
The engine oil level should be checked before
each ride. In addition, the oil must be changed
at the intervals specified in the periodic mainte-
nance and lubrication chart.
Engine oil level measurement
1. Place the machine on a level surface.
2. Warm up the engine for several minutes and
stop it.
3. Wait a few minutes until the oil level settles,
remove the oil filler cap, wipe off the dipstick
clean. Insert the dipstick in the filler hole
without screwing it in.
NOTE:
Wait a few minutes until the oil level settles
before checking.
4. Remove the dipstick and inspect the oil
level.
5. The oil level should be between the maxi-
mum and minimum marks. If the level is low,
add oil to raise it to the proper level.
qw
e
1. Dipstick
2. Maximum level mark 3. Minimum level mark
1. Jauge
2. Repère de niveau maximum 3. Repère de niveau minimum
1. Varilla de medición
2. Marca de máximo 3. Marca de mínimo
1C5-9-60-08 9/12/03 8:38 PM Page 8-14

8-15
cC
Be sure no foreign material enters the
crankcase.
Engine oil replacement and oil filter cleaning
1. Place the machine on a level surface.
2. Warm up the engine for several minutes and
stop it.
3. Place a container under the engine to col-
lect the used oil.
4. Remove the dipstick and drain bolt to drain
the oil.
cC
When removing the drain bolt, the compres-
sion spring, oil strainer and O-ring will fall
out. Take care not to lose these parts.
q
rewq
1. Drain bolt 2. O-ring
3. Compression spring 4. Oil strainer
1. Boulon de vidange 2. Joint torique
3. Ressort de compression 4. Crépine à huile
1. Tapón de drenaje 2. Junta torica
3. Resorte de compresión 4. Taza de aceite
1C5-9-60-08 9/12/03 8:38 PM Page 8-16

8-21
EBU14912
Final transmission oil
The final transmission case must be checked for
oil leakage before each ride. If any leakage is
found, have a Yamaha dealer check and repair
the machine. In addition, the final transmission
oil must be changed at the intervals specified in
the periodic maintenance and lubrication chart.
Final transmission oil measurement
1. Place the machine on a level surface.
2. Remove the screw and check the oil level. It
should be up to the brim of the hole. If the
oil level is low, remove the oil filler bolt, and
then add sufficient oil of the recommended
type to raise it to the proper level.
3. Install the screw and oil filler bolt, and then
tighten them to their specified torques.we
q
q
1. Screw 2. Brim 3. Correct oil level
1. Vis 2. Bord 3. Niveau d’huile correct
1. Tornillo 2. Borde 3. Nivel correcto de aceite
1. Oil filler bolt
1. Boulon de remplissage d’huile
1. Tapón de llenado de aceite
Tightening torque:
Screw:
16 Nm (1.6 m0kgf)
Oil filler bolt:
23 Nm (2.3 m0kgf)
1C5-9-60-08 9/12/03 8:38 PM Page 8-22