torque YAMAHA GRIZZLY 125 2013 User Guide

8-33
8
EBU30440Adjusting the rear brake lever free play The brake lever free play must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.TIPBefore adjusting the brake lever free play, check
the rear brake shoes for wear.The brake lever free play should measure 5.0–8.0
mm (0.20–0.31 in) as shown. If the free play is in-
correct, adjust it as follows.1. Loosen the locknut.
2. Turn the brake lever free play adjusting bolt in
direction (a) to increase the free play, and in
direction (b) to decrease it.
Tightening torque:
Front carrier bolt:7 Nm (0.7 m·kgf, 5.1 ft·lbf)
1. Brake lever free play
1
U1PY61E0.book Page 33 Wednesday, March 14, 2012 5:22 PM

8-36
8
the engine as well as other vital parts of
the ATV and can lead to drive chain slip-
page or breakage. To prevent this from oc-
curring, keep the drive chain slack within
the specified limits.
[ECB00542]
5. Tighten the drive chain slack adjusting bolt
locknut and the axle holding bolts to the spec-
ified torques.
NOTICEECB00551If measurement “A” of the drive chain slack ad-
justing bolt is less than 27 mm (1.06 in), have a
Yamaha dealer replace the drive chain.
1. Locknut
2. Drive chain slack adjusting bolt
1
2
(a)
(b)
Tightening torques:
Drive chain slack adjusting bolt locknut:16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle holding bolt (upper): 85 Nm (8.5 m·kgf, 61 ft·lbf)
Axle holding bolt (lower): 60 Nm (6.0 m·kgf, 43 ft·lbf)1. Measurement A
1
U1PY61E0.book Page 36 Wednesday, March 14, 2012 5:22 PM

8-37
86. Tighten the hub stopper bolt and hub stopper
bolt locknut to the specified torques.
EBU24882Lubricating the drive chain The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.NOTICEECB00561The drive chain must be lubricated after wash-
ing the ATV or riding in the rain or wet areas.1. Clean the drive chain with kerosene and asmall soft brush. NOTICE: To prevent dam-
aging the O-rings, do not clean the drive
chain with steam cleaners, high-pressure
washers or inappropriate solvents.
[ECB00571]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain lubricant. NOTICE: Do
not use engine oil or any other lubricants
for the drive chain, as they may contain
substances that could damage the O-
rings.
[ECB00581]
EBU24902
Checking and lubric ating the cables The operation and the condition of all control ca-
bles should be checked before each ride, and the
cables and cable ends should be lubricated if nec-
Tightening torques:
Hub stopper bolt:16 Nm (1.6 m·kgf, 12 ft·lbf)
Hub stopper bolt locknut: 16 Nm (1.6 m·kgf, 12 ft·lbf)1. O-ring
1
1
U1PY61E0.book Page 37 Wednesday, March 14, 2012 5:22 PM

8-49
8
TIPTapered nuts are used for both the front and rear
wheels. Install the nuts with their tapered side to-
wards the wheel.4. Lower the ATV to the ground.
5. Tighten the wheel nuts to the specifiedtorques.
EBU25720Troubleshooting Although Yamaha ATVs receive a thorough in-
spection before shipment from the factory, trouble
may occur during operation. Any problem in the fu-
el, compression, or ignition systems, for example,
can cause poor starting and loss of power.
The following troubleshooting chart represents a
quick and easy procedure for checking these vital
systems yourself. However, should your ATV re-
quire any repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary tools, expe-
rience, and know-how to service the ATV properly.
Use only genuine Yamaha replacement parts. Im-
itation parts may look like Yamaha parts, but they
are often inferior, have a shorter service life and
can lead to expensive repair bills.
1. Tapered nut
1
Tightening torques:Fro nt wh ee l nu t:55 Nm (5.5 m·kgf, 40 ft·lbf)
Rear wheel nut: 55 Nm (5.5 m·kgf, 40 ft·lbf)
U1PY61E0.book Page 49 Wednesday, March 14, 2012 5:22 PM