four wheel drive YAMAHA GRIZZLY 350 2007 Owners Manual

3-2
3
EBU17712Controls and instruments
NOTE:The ATV you have purchased may differ slightlyfrom the figures shown in this manual.
1. Rear brake lever
2. Handlebar switches
3. Starter (choke)
4. Parking brake lock plate
5. Horn switch
6. Drive select lever
7. Speedometer
8. Main switch
9. Fuel tank cap
10.On-Command four-wheel-drive/differential gear lock
switch
11.Throttle lever
12.Front brake leverU4S260E0.book Page 2 Tuesday, October 3, 2006 1:53 PM

4-2
4
EBU17813Indicator lights and warning light EBU28331Reverse indicator light “REVERSE”
This indicator light comes on when the transmis-
sion is in the reverse position.
Furthermore, this indicator light flashes:
when the override switch is being pushed,
when the engine is being raced for 10 seconds
or more.
NOTE:If the indicator light flashes under any other circum-
stances or the speedometer does not show the
speed while riding, have a Yamaha dealer checkthe speed sensor circuit.EBU17870Neutral indicator light “NEUTRAL”
This indicator light comes on when the transmis-
sion is in the neutral position.EBU26931Oil temperature warning light “”
This warning light comes on when the engine over-
heats. When this occurs, stop the engine as soon
as it is safe to do so, and allow it to cool.
The electrical circuit of the warning light can be
checked by turning the key to “ON”, with the engine
stop switch set to “”, and then pushing the start
switch.
If the warning light does not come on while the start
switch is being pushed, then go off after the start
switch is released, have a Yamaha dealer check
the electrical circuit.
1. Reverse indicator light “REVERSE”
2. Neutral indicator light “NEUTRAL”
3. Oil temperature warning light “”
4. On-Command differential gear lock indicator light “”
5. On-Command four-wheel-drive indicator light “”U4S260E0.book Page 2 Tuesday, October 3, 2006 1:53 PM

4-3
4 If the warning light stays on, allow the engine to
cool. If the warning light stays on when the engine
is cool, have a Yamaha dealer check the electrical
circuit.
CAUTION:ECB00010
The engine may overheat if the ATV is over-
loaded. In this case, reduce the load to spec-
ification.
Start the engine after making sure that the
warning light is out. Continuous use while
the warning light is on may cause damage tothe engine.EBU17952On-Command four-wheel-drive indicator light
“”
This indicator light comes on when the On-Com-
mand four-wheel-drive switch is set to the “4WD”
position.NOTE:Due to the synchronizing mechanism in the differ-
ential gear case, the light may not come on untilthe ATV starts moving.
EBU28341On-Command differential gear lock indicator
light “”
This indicator light and the On-Command four-
wheel-drive indicator light “” come on when the
On-Command differential gear lock switch is set to
the “LOCK” position.EBU18020Speedometer The speedometer shows the riding speed. This
speedometer is equipped with an odometer and a
tripmeter. The tripmeter can be reset to “0” with the
reset knob. Use the tripmeter to estimate how far
you can ride on a tank of fuel before going to re-
serve. This information will enable you to plan fuel
stops in the future.
U4S260E0.book Page 3 Tuesday, October 3, 2006 1:53 PM

4-6
4
WARNING
EWB00150Always ride at a slow speed when the ATV is in
four-wheel-drive differential gear lock, and al-
low extra time and distance for maneuvers.
All wheels turn at the same speed when the dif-
ferential is locked, so it takes more effort to
turn the ATV. The effort needed to turn increas-
es with the riding speed. You may lose control
and have an accident if you cannot make a
sharp enough turn for the speed you are trav-eling.EBU28430On-Command four-wheel-drive switch
“2WD”/“4WD”
This ATV is equipped with a switch to change from
two-wheel drive to four-wheel drive and vice-versa.
Select the appropriate drive according to the ter-
rain and the conditions.
“2WD” (two-wheel drive): Power is supplied to
the rear wheels.
“4WD” (four-wheel drive): Power is supplied to
the rear and front wheels.To change from two-wheel drive to four-wheel
drive, stop the ATV and push the switch in to the
“4WD” position. The four-wheel-drive indicator
light “” comes on.
To change from four-wheel drive to two-wheel
drive, stop the ATV and push the switch in to the
“2WD” position.
WARNING
EWB00161Always stop the ATV before changing from
two-wheel drive to four-wheel drive and vice-
versa. The ATV handles differently in two-
wheel drive than in four-wheel drive in some
circumstances. Changing from two-wheel1. On-Command four-wheel-drive switch “2WD”/“4WD”
U4S260E0.book Page 6 Tuesday, October 3, 2006 1:53 PM

4-7
4 drive to four-wheel drive or vice-versa while
moving may cause the ATV to unexpectedly
handle differently. This could distract the oper-
ator and increase the risk of losing control and
of causing an accident.EBU28370On-Command differential gear lock switch
“4WD”/“LOCK”
This ATV is equipped with a switch allowing you to
lock the differential gear when in four-wheel drive.
Select the appropriate switch position according to
the terrain and the conditions.
“4WD” (four-wheel drive): Power is supplied to
the rear and front wheels.
“LOCK” (four-wheel drive with the differential
gear locked): Power is supplied to the rear and
front wheels and the differential gear is locked.
Unlike in four-wheel drive, all wheels turn at the
same speed.To lock the differential gear in four-wheel drive,
make sure the On-Command four-wheel-drive
switch is pushed in to the “4WD” position.
1. On-Command four-wheel-drive switch “2WD”/“4WD”
2. On-Command differential gear lock switch “4WD”/“LOCK”
U4S260E0.book Page 7 Tuesday, October 3, 2006 1:53 PM

4-8
4
Stop the ATV, move the differential gear lock lever
to position (a), and then push the differential gear
lock switch in to the “LOCK” position. When the dif-
ferential gear is locked, the differential gear lock in-
dicator light “” comes on.To release the differential gear lock, stop the ATV
and push the switch to the “4WD” position.
WARNING
EWB00130Always stop the ATV before changing from
four-wheel drive to four-wheel-drive differen-
tial gear lock or vice-versa.
The ATV handles differently in four-wheel drive
than in differential gear lock in some circum-
stances. Changing from four-wheel drive to dif-
ferential gear lock or vice-versa while moving
may cause the ATV to handle differently unex-
1. Differential gear lock lever
2. On-Command four-wheel-drive switch “2WD”/“4WD”
1. On-Command differential gear lock switch “4WD”/“LOCK”
U4S260E0.book Page 8 Tuesday, October 3, 2006 1:53 PM

4-9
4 pectedly. This could distract the operator and
increase the risk of losing control and causing
an accident.
WARNING
EWB00140Always ride at a slow speed when the ATV is in
differential gear lock, and allow extra time and
distance for maneuvers.
All wheels turn at the same speed when the dif-
ferential gear is locked, so it takes more effort
to turn the ATV. The effort needed to turn in-
creases with the riding speed. You may lose
control and have an accident if you cannot
make a sharp enough turn for the speed youare traveling.NOTE:
If the differential gear lock is not engaging prop-
erly, turn the handlebar back and forth to help it
engage.
Riding before the differential gear lock is proper-
ly engaged will cause the engine speed to be
limited until engagement is complete.
When the ATV is in four-wheel-drive differential
gear lock, the maximum traveling speed is limit-
ed to 31 km/h (19 mi/h). However, if conditionsrequire full engine power to be available, push
and hold the override switch to disable the differ-
ential gear lock speed limiter. (See page 4-5 for
a detailed explanation of this switch.)EBU18280Throttle lever Once the engine is running, movement of the throt-
tle lever will increase the engine speed.
Regulate the speed of the ATV by varying the
throttle position. Because the throttle is spring-
loaded, the ATV will decelerate, and the engine will
return to an idle any time the hand is removed from
the throttle lever.1. Throttle lever
U4S260E0.book Page 9 Tuesday, October 3, 2006 1:53 PM

8-41
8
The main fuse and the fuse box are located under
the seat. (See page 4-17.)
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off all electrical
circuits.
CAUTION:ECB00640To prevent accidental short-circuiting, turn off
the main switch when checking or replacing afuse.
2. Remove the blown fuse, and then install a
new fuse of the specified amperage.
1. Headlight fuse
2. Ignition fuse
3. Auxiliary DC jack fuse (for optional auxiliary DC jack)
4. Four-wheel-drive motor fuse
5. Signaling system fuse
6. Spare fuse
Specified fuses:
Main fuse:
30.0 A
Headlight fuse:
15.0 A
Ignition fuse:
15.0 A
Four-wheel-drive motor fuse:
10.0 A
Signaling system fuse:
10.0 A
Auxiliary DC jack fuse:
10.0 A
U4S260E0.book Page 41 Tuesday, October 3, 2006 1:53 PM

10-5
10
Oil temperature warning light:
12 V, 1.7 W × 1
On-command four-wheel-drive indicator light:
12 V, 1.7 W × 1
Differential gear lock indicator light:
12 V, 1.7 W x 1Fuses:Main fuse:
30.0 A
Headlight fuse:
15.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
15.0 A
Auxiliary DC jack fuse:
10.0 A
Four-wheel-drive motor fuse:
10.0 A
U4S260E0.book Page 5 Tuesday, October 3, 2006 1:53 PM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-19
Axle boots .................................................................... 8-34BBattery .......................................................................... 8-39
Brake fluid, changing ................................................... 8-29
Brake fluid level, checking ........................................... 8-28
Brake lever free play, checking the front ...................... 8-29
Brake lever, front .......................................................... 4-11
Brake levers, checking and lubricating ........................ 8-36
Brake light switches ..................................................... 8-35
Brake pads and friction plates, checking ..................... 8-27
Brake pedal and brake lever free play (rear) and
brake pedal position, adjusting and checking ............ 8-30
Brake pedal and rear brake lever ................................. 4-11
Brake pedal, checking and lubricating ......................... 8-37
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................. 8-36
Carburetor, adjusting ................................................... 8-24
Carrier, front ................................................................. 4-19
Carrier, rear .................................................................. 4-19
Chassis fasteners .......................................................... 5-7
Cleaning ......................................................................... 9-1DDifferential gear lock indicator light ................................ 4-3
Differential gear oil ................................................ 5-3, 8-17Drive select lever ......................................................... 4-12
Drive select lever and driving in reverse ........................ 6-3
Drive select lever safety system cable, adjusting ........ 8-27
Drive shaft universal joint, lubricating .......................... 8-37
EEngine break-in .............................................................. 6-4
Engine, cold start ........................................................... 6-1
Engine idling speed ..................................................... 8-25
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-10
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil ......................................................... 5-3, 8-14
Four-wheel-drive indicator light ...................................... 4-3
Fuel ....................................................................... 4-14, 5-3
Fuel cock ..................................................................... 4-15
Fuel tank cap ............................................................... 4-13
Fuses, replacing .......................................................... 8-40HHandlebar switches ....................................................... 4-4
Headlight beam, adjusting ........................................... 8-44
Headlight bulb, replacing ............................................. 8-42
Horn switch .................................................................... 4-5IIdentification numbers .................................................. 11-1
Indicator lights and warning light ................................... 4-2
Instruments, lights and switches .................................... 5-7
U4S260E0.book Page 1 Tuesday, October 3, 2006 1:53 PM