differential YAMAHA GRIZZLY 350 2011 User Guide

5-1
5
EBU19201
PRE-OPERATION CHECKS
EBU19224Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always
follow the inspection and maintenance procedures and schedules described in the Owner’s Manual.
WARNING
EWB00481Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equip-
ment damage. Do not operate the vehicle if you find any problem. If a problem cannot be corrected
by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer.Before using this vehicle, check the following points:
ITEM ROUTINE PAGE
FuelCheck fuel level in fuel tank, and add recommended fuel if neces-
sary.
Check fuel line for leakage. Correct if necessary.4-13, 5-3
Engine oilCheck oil level in engine, and add recommended oil to specified lev-
el if necessary.
Check ATV for oil leakage. Correct if necessary.5-3, 8-12
Final gear oilCheck ATV for oil leakage. Correct if necessary. 5-3, 8-16
Differential gear oilCheck ATV for oil leakage. Correct if necessary. 5-3, 8-18
U4S264E0.book Page 1 Thursday, August 5, 2010 1:24 PM

5-3
5
EBU19541Fuel Make sure that there is sufficient fuel in the tank.
(See page 4-13.)EBU19560Engine oil Make sure that the engine oil is at the specified lev-
el. Add oil as necessary. (See page 8-12.)EBU19590Final gear oil Make sure that the final gear oil is at the specified
level. Add oil as necessary. (See page 8-16.)EBU19600Differential gear oil Make sure that the differential gear oil is at the
specified level. Add oil as necessary. (See page
8-18.)EBU28531Front and rear brakes Brake levers and brake pedal
Check that there is no free play in the front brake
lever. If there is free play, have a Yamaha dealer
check the brake system.

Check for correct free play in the rear brake lever
and brake pedal. If the free play is incorrect, ad-
just it. (See page 8-32.)
Check operation of the levers and pedal. They
should move smoothly and there should be a
firm feeling when the brake is applied. If not,
have a Yamaha dealer check them.
Brake fluid level (front brake)
Check the brake fluid level. Add fluid if necessary.
(See page 8-30.)
Brake fluid leakage (front brake)
Check to see if any brake fluid is leaking out of the
hose, joint or brake fluid reservoir of the front
brake. Apply the brake firmly for one minute. If the
lever moves slowly inward, there may be a leak in
the brake system. If there is any leakage, the brake
system should be checked by a Yamaha dealer.Recommended brake fluid:
DOT 4
U4S264E0.book Page 3 Thursday, August 5, 2010 1:24 PM

8-7
8
13*Rear knuckle pivotsLubricate with lithium-soap-based grease.√√√
14*Steering shaftLubricate with lithium-soap-based grease.√√√
15*Steering systemCheck operation and repair or replace if damaged.
Check toe-in and adjust if necessary.√√√√√
16*Engine mountCheck for cracks or other damage, and replace if
necessary.√√√
17*Axle bootsCheck for cracks or other damage, and replace if
necessary.√√√√√
18 Engine oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√ √√√
19Engine oil filter car-
tridgeReplace.√√√
20 Differential gear oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√√
21 Final gear oilChange.
Check ATV for oil leakage, and correct if neces-
sary.√ √√√
22*Moving parts and
cablesLubricate.√√√√ NO. ITEMCHECK OR MAINTENANCE
JOBINITIAL EVERY
Whichev-
er comes
firstmonth136612
km
(mi)320
(200)1300
(800)2500
(1600)2500
(1600)5000
(3200)
hours 20 80 160 160 320U4S264E0.book Page 7 Thursday, August 5, 2010 1:24 PM

8-18
8
TIPIf the recommended oil is not available, SAE80W-
90 API GL-5 Hypoid gear oil may be used instead.
However, when using this oil, noise from the final
gear case may occur when applying the rear
brake.
7. Install the oil filler bolt and its new O-ring, and
then tighten the bolt to the specified torque.
8. Check the final gear case for oil leakage. If oil
is leaking, check for the cause.
9. Install the engine guard and the final gear
case guard by installing the bolts, and then
tightening them to the specified torques.EBU23426Differential gear oil The differential gear case must be checked for oil
leakage before each ride. If any leakage is found,
have a Yamaha dealer check and repair the ATV.
In addition, the differential gear oil level must be
1. Final gear oil filler bolt
2. O-ring
3. Final gear oil
4. Correct oil levelRecommended final gear oil:
See page 10-1.1
2
3
4
Tightening torque:
Final gear oil filler bolt:
24 Nm (2.4 m·kgf, 17 ft·lbf)
Tightening torques:
Engine guard bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Final gear case guard bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
U4S264E0.book Page 18 Thursday, August 5, 2010 1:24 PM

8-19
8checked and the oil changed as follows at the in-
tervals specified in the periodic maintenance and
lubrication chart.
To check the differential gear oil level
1. Place the ATV on a level surface.
2. Remove the differential gear oil filler bolt and
its gasket, and then check the oil level in the
differential gear case. The oil level should be
at the brim of the filler hole.3. If the oil is below the brim of the filler hole, add
sufficient oil of the recommended type to raise
it to the correct level.
4. Check the gasket for damage, and replace it if
necessary.
5. Install the oil filler bolt and its gasket, and then
tighten the bolt to the specified torque.
To change the differential gear oil
1. Place the ATV on a level surface.
2. Place an oil pan under the differential gear
case to collect the used oil.
3. Remove the differential gear oil filler bolt, the
differential gear oil drain bolt and their gasket
to drain the oil from the differential gear case.
1. Differential gear oil filler bolt
2. Gasket
3. Differential gear oil
4. Correct oil level
1
2
3
4
Tightening torque:
Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
U4S264E0.book Page 19 Thursday, August 5, 2010 1:24 PM

8-20
8 4. Install the drain bolt and its new gasket, and
then tighten the bolt to the specified torque.
5. Refill with the recommended differential gear
oil to the brim of the filler hole as shown.
NOTICE: Be sure no foreign material en-
ters the differential gear case.
[ECB00411]
6. Check the oil filler bolt gasket for damage, and
replace it if necessary.
7. Install the oil filler bolt and its gasket, and then
tighten the bolt to the specified torque.
1. Differential gear oil drain bolt
2. GasketTightening torque:
Differential gear oil drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
12
1. Differential gear oil filler bolt
2. Gasket
3. Differential gear oil
4. Correct oil levelRecommended differential gear oil:
See page 10-1.
Tightening torque:
Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
1
2
3
4
U4S264E0.book Page 20 Thursday, August 5, 2010 1:24 PM

8-21
88. Check the differential gear case for oil leak-
age. If oil is leaking, check for the cause.
EBU23646Cleaning the air filter element The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.TIPThere is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.
1. Place the ATV on a level surface.
2. Remove the seat. (See page 4-17.)
3. Remove the air filter case cover by unhooking
the air filter case cover holders.1. Air filter case check hose
U4S264E0.book Page 21 Thursday, August 5, 2010 1:24 PM

10-2
10
Type:
SAE 5W-30, 10W-30, 10W-40, 15W-40, 20W-40 or 20W-
50
Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter cartridge replacement:
2.20 L (2.33 US qt, 1.94 Imp.qt)
With oil filter cartridge replacement:
2.30 L (2.43 US qt, 2.02 Imp.qt)Final gear oil:Type:
YFM35FGIA Yamaha Friction Modified Shaft Drive Gear
Oil
YFM35FWANA Yamaha Friction Modified Shaft Drive
Gear Oil (Part No.: ACC-SHAFT-LU-00)Quantity:
0.50 L (0.53 US qt, 0.44 Imp.qt)
Differential gear oil:Type:
YFM35FGIA Yamaha Friction Modified Shaft Drive Gear
Oil or SAE 80 API GL-4 Hypoid gear oil
YFM35FWANA Yamaha Friction Modified Shaft Drive
Gear Oil (Part No.: ACC-SHAFT-LU-00) or SAE 80 API
GL-4 Hypoid gear oil
Quantity:
0.23 L (0.24 US qt, 0.20 Imp.qt)Air filter:Air filter element:
Wet elementFuel:Recommended fuel:
YFM35FGIA Regular unleaded gasoline only
YFM35FWANA Unleaded gasoline only
Fuel tank capacity:
13.5 L (3.57 US gal, 2.97 Imp.gal)
Fuel reserve amount:
3.3 L (0.87 US gal, 0.73 Imp.gal)Carburetor:Type × quantity:
BSR33 x 1Spark plug (s):Manufacturer/model:
NGK/DR8EA
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
0 10 30 50 70 90 110 130 ˚F
–20 –10 0 10 20 30 40 50 ˚CSAE 5W-30
SAE 10W-30
SAE 10W-40
SAE 15W-40
SAE 20W-40SAE 20W-50
U4S264E0.book Page 2 Thursday, August 5, 2010 1:24 PM

10-4
10
Rear wheel:Wheel type:
Panel wheel
Rim size:
12 x 7.5ATFront brake:Type:
Disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4Rear brake:Type:
Wet multiple disc brake
Operation:
Left hand and right foot operationFront suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
160 mm (6.3 in)Rear suspension:Type:
Double wishbone
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
180 mm (7.1 in)
Electrical system:Ignition system:
DC CDI
Charging system:
AC magnetoBattery:Model:
YTX14AH
Voltage, capacity:
12 V, 12.0 AhHeadlight:Bulb type:
Krypton bulbBulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Tail/brake light:
12 V, 5.0/21.0 W × 1
Meter lighting:
12 V, 1.7 W × 1
Neutral indicator light:
12 V, 1.7 W × 1
Reverse indicator light:
12 V, 1.7 W × 1
Oil temperature warning light:
12 V, 1.7 W × 1
On-command four-wheel-drive indicator light:
12 V, 1.7 W × 1
Differential gear lock indicator light:
12 V, 1.7 W x 1
U4S264E0.book Page 4 Thursday, August 5, 2010 1:24 PM

INDEX
AAccessories and loading ................................................ 6-6
Air filter element, cleaning ............................................ 8-21
Axle boots .................................................................... 8-36BBattery .......................................................................... 8-41
Brake fluid, changing .................................................... 8-31
Brake fluid level, checking ............................................ 8-30
Brake lever free play, checking the front ...................... 8-32
Brake lever, front .......................................................... 4-10
Brake levers, checking and lubricating ......................... 8-38
Brake light switches ..................................................... 8-37
Brake pads and friction plates, checking ...................... 8-29
Brake pedal and rear brake lever ................................. 4-11
Brake pedal, checking and lubricating ......................... 8-39
Brakes .......................................................................... 8-29
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................. 8-37
Carburetor, adjusting .................................................... 8-26
Carrier, front ................................................................. 4-19
Carrier, rear .................................................................. 4-19
Chassis fasteners ........................................................... 5-6
Cleaning ......................................................................... 9-1DDifferential gear oil ................................................ 5-3, 8-18
Drive select lever .......................................................... 4-12
Drive select lever and driving in reverse ........................ 6-3Drive select lever safety system cable, adjusting ......... 8-29
Drive shaft universal joint, lubricating ........................... 8-40
EEngine break-in .............................................................. 6-4
Engine, cold start ........................................................... 6-1
Engine idling speed ...................................................... 8-26
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge ................................... 8-12
Engine, starting a warm ................................................. 6-3
Engine stop switch ......................................................... 4-4FFinal gear oil .......................................................... 5-3, 8-16
Four-wheel-drive indicator light ...................................... 4-3
Fuel ....................................................................... 4-13, 5-3
Fuel cock ...................................................................... 4-15
Fuel tank cap ................................................................ 4-13
Fuses, replacing ........................................................... 8-44HHandlebar switches ........................................................ 4-4
Headlight beam, adjusting ............................................ 8-47
Headlight bulb, replacing .............................................. 8-45
Horn switch .................................................................... 4-5IIdentification numbers .................................................. 11-1
Indicator lights and warning light .................................... 4-2
Instruments, lights and switches .................................... 5-6LLabel locations ............................................................... 1-1
U4S264E0.book Page 1 Thursday, August 5, 2010 1:24 PM