torque YAMAHA GRIZZLY 450 2010 Owners Manual

8-2
8The service information included in this manual
and the tools provided in the owner’s tool kit are in-
tended to assist you in the performance of preven-
tive maintenance and minor repairs. However,
additional tools such as a torque wrench may be
necessary to perform certain maintenance work
correctly.
TIPIf you do not have the tools or experience required
for a particular job, have a Yamaha dealer perform
it for you.1. Owner’s manual
2. Owner’s tool kit
3. Low-pressure tire gaugeU37S61E0.book Page 2 Tuesday, June 2, 2009 10:33 AM

8-13
8 To install the panel
1. Place the panel in the original position, and
then install the quick fastener screws.
2. Place the carrier in the original position, and
then install the carrier bolts under the fenders.
3. Install the carrier top bolts, and then tighten all
bolts to the specified torques.Panel E
To remove the panel
Remove the bolts, and then take the panel off.
1. Quick fastener screw
2. Panel C
1
2
Tightening torques:
Carrier bolt (top):
34 Nm (3.4 m·kgf, 24 ft·lbf)
Carrier bolt (under fenders):
7 Nm (0.7 m·kgf, 5.1 ft·lbf)1. Panel E
2. Bolt
U37S61E0.book Page 13 Tuesday, June 2, 2009 10:33 AM

8-16
82. Check the spark plug for electrode erosion
and excessive carbon or other deposits, and
replace it if necessary.
3. Measure the spark plug gap with a wire thick-
ness gauge and, if necessary, adjust the gap
to specification.To install the spark plug
1. Clean the surface of the spark plug gasket
and its mating surface, and then wipe off any
grime from the spark plug threads.
2. Install the spark plug with the spark plug
wrench, and then tighten it to the specified
torque.
TIPIf a torque wrench is not available when installing
the spark plug, a good estimate of the correct
torque is 1/4–1/2 turn past finger tight. However,
the spark plug should be tightened to the specified
torque as soon as possible.3. Install the spark plug cap.
4. Install the panel. Specified spark plug:
NGK/DR8EA
1. Spark plug gapSpark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Tightening torque:
Spark plug:
17.5 Nm (1.75 m·kgf, 12.7 ft·lbf)
U37S61E0.book Page 16 Tuesday, June 2, 2009 10:33 AM

8-20
8
TIPMake sure that the O-ring is properly seated.9. Install the new oil filter cartridge with an oil fil-
ter wrench, and then tighten it to the specified
torque with a torque wrench.10. Install panels E and D.
11. Install the engine oil drain bolt, and then tight-
en it to the specified torque.1. O-ring
1. Torque wrenchTightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
Tightening torque:
Engine oil drain bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
U37S61E0.book Page 20 Tuesday, June 2, 2009 10:33 AM

8-22
82. Remove the final gear oil filler bolt, and then
check the oil level in the final gear case. The
oil level should be at the brim of the filler hole.
3. If the oil is below the brim of the filler hole, add
sufficient oil of the recommended type to raise
it to the correct level.
4. Install the oil filler bolt, and then tighten it to the
specified torque.To change the final gear oil
1. Place the ATV on a level surface.
2. Remove the engine guard and the final gear
case guard by removing the bolts.
3. Place an oil pan under the final gear case to
collect the used oil.
4. Remove the final gear oil filler bolt and the fi-
nal gear oil drain bolt to drain the oil from the
final gear case.
1. Final gear oil filler bolt
2. Correct oil level
3. Final gear oilTightening torque:
Final gear oil filler bolt:
24 Nm (2.4 m·kgf, 17 ft·lbf)
1. Engine guard
2. Final gear case guard
3. Bolt
U37S61E0.book Page 22 Tuesday, June 2, 2009 10:33 AM

8-23
8 5. Install the drain bolt, and then tighten it to the
specified torque.
6. Refill with the recommended final gear oil to
the brim of the filler hole as shown. NOTICE:
Be sure no foreign material enters the final
gear case.
[ECB00421]
TIPIf the recommended oil is not available, SAE80W-
90 API GL-5 Hypoid gear oil may be used instead.
However, when using this oil, noise from the final
gear case may occur when applying the rear
brake.7. Install the oil filler bolt, and then tighten it to the
specified torque.
1. Final gear oil drain boltTightening torque:
Final gear oil drain bolt:
24 Nm (2.4 m·kgf, 17 ft·lbf)
1. Final gear oil filler bolt
2. Correct oil level
3. Final gear oilRecommended final gear oil:
See page 10-1.
U37S61E0.book Page 23 Tuesday, June 2, 2009 10:33 AM

8-24
88. Check the final gear case for oil leakage. If oil
is leaking, check for the cause.
9. Install the engine guard and the final gear
case guard by installing the bolts, and then
tightening them to the specified torques.
EBU23423Differential gear oil The differential gear case must be checked for oil
leakage before each ride. If any leakage is found,
have a Yamaha dealer check and repair the ATV.
In addition, the differential gear oil level must be
checked and the oil changed as follows at the in-
tervals specified in the periodic maintenance and
lubrication chart.To check the differential gear oil level
1. Place the ATV on a level surface.
TIPThe differential gear oil level must be checked
when the engine is cold.2. Remove the differential gear oil filler bolt, and
then check the oil level in the differential gear
case. The oil level should be at the brim of the
filler hole. Tightening torque:
Final gear oil filler bolt:
24 Nm (2.4 m·kgf, 17 ft·lbf)
Tightening torques:
Engine guard bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)
Final gear case guard bolt:
7 Nm (0.7 m·kgf, 5.1 ft·lbf)1. Differential gear oil
2. Differential gear oil filler bolt
3. Correct oil level
U37S61E0.book Page 24 Tuesday, June 2, 2009 10:33 AM

8-25
8 3. If the oil is below the brim of the filler hole, add
sufficient oil of the recommended type to raise
it to the correct level.
4. Install the oil filler bolt, and then tighten it to the
specified torque.
To change the differential gear oil
1. Place the ATV on a level surface.
2. Place an oil pan under the differential gear
case to collect the used oil.
3. Remove the differential gear oil filler bolt and
the differential gear oil drain bolt to drain the
oil from the differential gear case.4. Install the drain bolt, and then tighten it to the
specified torque.
5. Refill with the recommended differential gear
oil to the brim of the filler hole as shown.
NOTICE: Be sure no foreign material en-
ters the differential gear case.
[ECB00411]
Tightening torque:
Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
1. Differential gear oil drain boltTightening torque:
Differential gear oil drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
U37S61E0.book Page 25 Tuesday, June 2, 2009 10:33 AM

8-26
8
6. Install the oil filler bolt, and then tighten it to the
specified torque.
7. Check the differential gear case for oil leak-
age. If oil is leaking, check for the cause.
EBU23470Coolant The coolant level should be checked before each
ride. In addition, the coolant must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.EBU27124To check the coolant level
1. Place the ATV on a level surface.TIPThe coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.2. Check the coolant level in the coolant reser-
voir.TIPThe coolant should be between the minimum and
maximum level marks.
1. Differential gear oil
2. Differential gear oil filler bolt
3. Correct oil levelRecommended differential gear oil:
See page 10-1.
Tightening torque:
Differential gear oil filler bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
U37S61E0.book Page 26 Tuesday, June 2, 2009 10:33 AM

8-29
8 6. Remove panel D. (See page 8-9.)
7. Remove the coolant reservoir cap.
8. Disconnect the hose on the coolant reservoir
side, and then drain the coolant from the cool-
ant reservoir.9. After draining the coolant, thoroughly flush the
cooling system with clean tap water.
10. Replace the coolant drain bolt washer if it is
damaged, install the coolant drain bolt, and
then tighten it to the specified torque.
11. Connect the coolant reservoir hose.
12. Pour the recommended coolant into the reser-
voir to the maximum level mark, and then in-
stall the reservoir cap. NOTICE: Mix
1. Radiator cap
1. Coolant reservoir hoseTightening torque:
Coolant drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
U37S61E0.book Page 29 Tuesday, June 2, 2009 10:33 AM