recommended oil YAMAHA GRIZZLY 660 2003 Owners Manual
[x] Cancel search | Manufacturer: YAMAHA, Model Year: 2003, Model line: GRIZZLY 660, Model: YAMAHA GRIZZLY 660 2003Pages: 442, PDF Size: 17.57 MB
Page 134 of 442
5-15
EBU00947
Engine oil
Make sure the engine oil is at the specified level.
Fill with oil as necessary. (See pages 8-33 ~ 8-43
for details.)
Recommended oil:
Recommended engine oil classification:
API Service SE, SF, SG type or higher
-20˚ -10˚ 0˚
10˚20˚ 30˚40˚50˚C
10W/30
15W/4020W/4020W/50
10W/40
5W/30
U5KM60.book Page 15 Thursday, June 21, 2001 2:40 PM
Page 138 of 442
5-19
EBU00493
Final gear oil
Make sure the final gear oil is at the specified level.
Add oil as necessary. (See pages 8-43 ~ 8-47 for
details.)
If desired, an SAE 80W90 hypoid gear oil may be
used for all conditions.NOTE:GL-4 is a quality and additive rating, GL-5 or GL-6
rated hypoid gear oils may also be used.
Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
U5KM60.book Page 19 Thursday, June 21, 2001 2:40 PM
Page 140 of 442
5-21
EBU00678
Differential gear oil
Make sure the differential gear oil is at the speci-
fied level. Add oil as necessary. (See pages 8-49 ~
8-53 for details.)
EBU00497*
Coolant
Check the coolant level in the reservoir tank when
the engine is cold. (The coolant level will vary with
engine temperature.) The coolant level is satisfac-
tory if it is between the “FULL” and “LOW” marks
on the tank. If the coolant level is at or below the
“LOW” level, add tap water (soft water) to bring the
level up to “FULL”. Change the coolant every two
years. (See pages 8-55 ~ 8-65 for details.)CAUTION:_ Hard water or salt water is harmful to the en-
gine. You may use distilled water if you can’t
get soft water. _
Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
U5KM60.book Page 21 Thursday, June 21, 2001 2:40 PM
Page 273 of 442
8-8
* It is recommended that these items be serviced by a Yamaha dealer.
** Lithium-soap-based greaseNOTE:Recommended brake fluid: DOT 4
Brake fluid replacement:
1. When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally check
the brake fluid level and add fluid as required.
2. On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two years.
3. Replace the brake hoses every four years, or if cracked or damaged.Wheels*•Check balance/damage/runout.
•Repair if necessary.Wheel bearing*•Check bearing assemblies for looseness/damage.
•Replace if damaged.Front and rear
suspension*•Check operation.
•Correct if necessary.Steering system*•Check operation/Replace if damaged.
•Check toe-in/Adjust if necessary.Rear upper and lower
knuckle pivots*•Lubricate.**Drive shaft universal
joint*•Lubricate.**Engine mount*
•Check for cracks or damage.Front and rear axle boots*•Check operation.
•Replace if damaged.Stabilizer bushes*
•Check for cracks or damage.Fittings and Fasteners*•Check all chassis fittings and fasteners.
•Correct if necessary.
ITEM ROUTINEWhichever
comes firstINITIAL EVERY
km 320 1,200 2,400 2,400 4,800
hours 20 75 150 150 300
U5KM60.book Page 8 Thursday, June 21, 2001 2:40 PM
Page 306 of 442
8-41
9. Fill the engine with sufficient oil to reach the
specified level. Install the dipstick and tighten
it.CAUTION:_
Do not put in any chemical additives. En-
gine oil also lubricates the clutch and addi-
tives could cause clutch slippage.
Be sure no foreign material enters the
crankcase.
_
Recommended oil:
See page 10-2.
Oil quantity:
Total amount:
2.2 L
Periodic oil change:
1.9 L
With oil filter replacement:
2.0 L
U5KM60.book Page 41 Thursday, June 21, 2001 2:40 PM
Page 310 of 442
8-45
4. Install the drain bolt and tighten it to the spec-
ified torque.
5. Fill the final gear case with oil.CAUTION:_ Be sure no foreign material enters the final
gear case. _6. Install the filler bolt and tighten to the speci-
fied torque. Tightening torque:
Drain bolt (final gear case):
23 Nm (2.3 m·kgf)
Recommended oil:
See page 10-3.
Oil quantity:
Periodic oil change:
0.25 L
Total amount:
0.30 L
U5KM60.book Page 45 Thursday, June 21, 2001 2:40 PM
Page 318 of 442
8-53
5. Fill the differential gear case with oil.CAUTION:
Be sure no foreign material enters the differen-
tial gear case. 6. Install the filler bolt and tighten it to the speci-
fied torque.
7. Check for oil leakage. If oil leakage is found,
check for the cause. Recommended oil:
SAE 80 API “GL-4” Hypoid gear oil
Oil quantity:
Periodic oil change:
0.28 L
Total amount:
0.33 L
U5KM60.book Page 53 Thursday, June 21, 2001 2:40 PM
Page 372 of 442
8-107
EBU00570
Cable inspection and lubrication
WARNING
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer cov-
ering of control cables becomes damaged.
Cables can also become frayed or kinked. Op-
eration of controls could be restricted, which
could cause an accident or injury.Lubricate the inner cables and the cable ends. If
the cables do not operate smoothly, ask a Yamaha
dealer to replace them.
Recommended lubricant:
Engine oil
U5KM60.book Page 107 Thursday, June 21, 2001 2:40 PM
Page 419 of 442
10-2
10
Compression ratio 9.1 :1
Starting system Electric and recoil starter
Lubrication system Wet sump
Engine oil:
Type
Recommended engine oil classification API Service SE, SF, SG type or higherModel YFM660FP
-20˚-10˚0˚
10˚20˚30˚40˚50˚C
10W/30
15W/4020W/4020W/50
10W/40
5W/30
CAUTION:
Be sure to use motor oils that do not contain anti-
friction modifiers. Passenger car motor oils (often
labeled “Energy Conserving II”) contain anti-fric-
tion additives which will cause clutch and/or
starter clutch slippage, resulting in reduced com-
ponent life and poor engine performance.
U5KM60.book Page 2 Thursday, June 21, 2001 2:40 PM