oil YAMAHA KODIAK 400 2002 Notices Demploi (in French)

8-7
EBU00262
PERIODIC MAINTENANCE/LUBRICATION
ITEM ROUTINEINITIAL EVERY
1
month3
months6
months6
months1
year
Valves*•Check valve clearance.
•Adjust if necessary.
Cooling system•Check coolant leakage.
•Repair if necessary.
•Replace coolant every 24 months.Spark plug•Check condition.
•Adjust gap and clean.
•Replace if necessary.Air filter•Clean.
•Replace if necessary.Every 20~40 hours
(More often in wet or dusty areas.)
Crankcase breather
system*•Check breather hose for cracks or damage.
•Replace if necessary.Exhaust system*•Check for leakage.
•Retighten if necessary.
•Replace gasket(s) if necessary.Carburetor*•Check and adjust idle speed/starter operation.
•Adjust if necessary.Fuel line*•Check fuel hose for cracks or damage.
•Replace if necessary.Engine oil
•Replace (Warm engine before draining).Engine oil filter cartridge
•Replace.Engine oil strainer*
•Clean.Final gear oil
•Check oil level/oil leakage.
•Replace every 12 months.Differential gear oil
Front brake*•Check operation/fluid leakage/see NOTE page 8-8.
•Correct if necessary.Rear brake*•Check operation/fluid leakage/see NOTE page 8-8.
•Correct if necessary.U5GH62.book Page 7 Monday, August 6, 2001 9:09 AM

8-8
* It is recommended that these items be serviced by a Yamaha dealer.NOTE:Recommended brake fluid: DOT 4
Brake fluid replacement:
1. When disassembling the master cylinder or caliper cylinder, replace the brake fluid. Normally check
the brake fluid level and add fluid as required.
2. On the inner parts of the master cylinder and caliper cylinder, replace the oil seals every two years.
3. Replace the brake hoses every four years, or if cracked or damaged.V-belt*•Check operation.
•Check for cracks or damage every 12 months or
2,400 km whichever comes first.Wheels*•Check balance/damage/runout.
•Repair if necessary.Wheel bearing*•Check bearing assemblies for looseness/damage.
•Replace if damaged.Front and rear
suspension*•Check operation.
•Correct if necessary.Steering system*•Check operation/Replace if damaged.
•Check toe-in/Adjust if necessary.Axle boots*•Check operation.
•Replace if damaged.Fittings and Fasteners*•Check all chassis fittings and fasteners.
•Correct if necessary.
ITEM ROUTINEINITIAL EVERY
1
month3
months6
months6
months1
year
U5GH62.book Page 8 Monday, August 6, 2001 9:09 AM

8-31 1. Engine oil dipstick
1. Jauge d’huile
1. Varilla de medición del aceite de motor
1. Maximum level mark 2. Minimum level mark
1. Repère de niveau maximum 2. Repère de niveau minimum
1. Marca de nivel máximo 2. Marca de nivel mínimo
EBU00847
Engine oil
Oil level inspection
1. Remove panel E. (See page 8-27 for panel
removal and installation procedures.)
2. Place the ATV on a level place and warm up
the engine for several minutes.
3. Stop the engine.
4. Remove the dipstick and wipe it off with a
clean rag. Insert the dipstick in the filler hole
without screwing it in.NOTE:_ Wait a few minutes until the oil level settles before
checking. _5. The oil level should be between the maxi-
mum and minimum marks. If the level is low,
fill the engine with sufficient oil to reach the
specified level.
U5GH62.book Page 31 Monday, August 6, 2001 9:09 AM

8-33 1. Engine oil drain bolt
2. Oil strainer
1. Boulon de vidange de l’huile
2. Crépine à huile
1. Perno de drenaje del aceite de motor
2. Colador de aceite
Engine oil and oil filter cartridge replacement
1. Remove panels E and F. (See pages 8-27 ~
8-29 for panel removal and installation pro-
cedures.)
2. Warm up the engine for several minutes.
3. Stop the engine. Place an oil pan under the
engine and remove the dipstick.
4. Remove the drain bolt and drain the oil.
U5GH62.book Page 33 Monday, August 6, 2001 9:09 AM

8-35 1. Oil filter element
1.Élément de filtre à huile
1. Elemento del filtro de aceite
1. Oil filter wrench
1. Clé pour filtre à huile
1. Llave para filtros de aceite
5. Remove the oil filter by using an oil filter
wrench.NOTE:_ An oil filter wrench is available at a nearby
Yamaha dealer. _6. Install the drain bolt and tighten it to the spec-
ified torque.
Tightening torque:
Drain bolt:
32 Nm (3.2 m·kgf)
U5GH62.book Page 35 Monday, August 6, 2001 9:09 AM

8-37 1. Torque wrench
1. Clé dynamométrique
1. Llave de apriete
7. Apply a light coat of engine oil to the O-ring of
the new oil filter.NOTE:_ Make sure the O-ring is seated properly. _8. Install the oil filter and tighten it to the speci-
fied torque with a torque wrench.
Tightening torque:
Oil filter:
17 Nm (1.7 m·kgf)
U5GH62.book Page 37 Monday, August 6, 2001 9:09 AM

8-39
9. Fill the engine with sufficient oil to reach the
specified level. Install the dipstick and tighten
it.CAUTION:_

Do not put in any chemical additives. En-
gine oil also lubricates the clutch and addi-
tives could cause clutch slippage.


Be sure no foreign material enters the
crankcase.
_
Recommended oil:
See page 10-2.
Oil quantity:
Total amount:
2.6 L
Periodic oil change:
2.3 L
With oil filter replacement:
2.4 L
U5GH62.book Page 39 Monday, August 6, 2001 9:09 AM

8-41
‘1. Final gear oil
2. Final gear case filler bolt
3. Proper level
1. Huile de transmission finale
2. Boulon de remplissage du carter de transmission finale
3. Niveau correct
1. Aceite de la transmisión final
2. Tapa de la caja del filtro
3. Nivel adecuado
10. Start the engine and warm it up for several
minutes. While warming up, check for oil
leakage. If oil leakage is found, stop the en-
gine immediately and check for the cause.
11. Install the panels.
EBU00825
Final gear oil
Final gear oil measurement
1. Place the machine on a level place.
2. Remove the oil filler bolt and check the oil lev-
el. It should be up to the brim of the hole. If
the level is low, add oil to raise it to the proper
level.CAUTION:_ Be sure no foreign material enters the final
gear case. _
U5GH62.book Page 41 Monday, August 6, 2001 9:09 AM

8-43 1. Final gear case cover 2. Bolt (× 2)
1. Couvercle du carter de transmission finale 2. Boulon (× 2)
1. Cubierta del cárter de la transmisión final 2. Perno (× 2)
1. Final gear oil drain bolt
1. Boulon de vidange d’huile de transmission finale
1. Perno de drenaje de aceite del engranaje final
3. Install the oil filler bolt and tighten it to the
specified torque.
Final gear oil replacement
1. Remove the final gear case cover.
2. Place the machine on a level place.
3. Place a container under the final gear case to
collect the used oil.
4. Remove the oil filler bolt and the drain bolt to
drain the oil.
5. Install the drain bolt and tighten it to the spec-
ified torque. Tightening torque:
Oil filler bolt:
23 Nm (2.3 m·kgf)
Tightening torque:
Drain bolt (final gear case):
23 Nm (2.3 m·kgf)
U5GH62.book Page 43 Monday, August 6, 2001 9:09 AM

8-45
6. Fill the final gear case with oil.CAUTION:_ Be sure no foreign material enters the final
gear case. _7. Install the filler bolt and tighten to the speci-
fied torque.
8. Check for oil leakage. If oil leakage is found,
check for the cause.
9. Install the final gear case cover.Recommended oil:
See page 10-3.
Oil quantity:
Periodic oil change:
0.19 L
Total amount:
0.22 L
Tightening torque:
Filler bolt (final gear case):
23 Nm (2.3 m·kgf)
U5GH62.book Page 45 Monday, August 6, 2001 9:09 AM