lock YAMAHA KODIAK 700 2018 Owner's Guide

8-63
8YFM70KPXJ / YFM70KPAJ / YFM70KPHJ /
YFM70KPSJ
EBU25614Replacing the tail/brake light bulbIf the tail/brake light bulb burns out, replace it as
follows.
1. Remove the tail/brake light bulb holder (to- gether with the bulb) by turning it counter-
clockwise. 2. Remove the burnt-out bulb by pushing it in
and turning it counterclockwise.1. Handlebar-mounted light beam adjusting screw
(b)
(a)
1
1. Tail/brake light bulb holder
1. Tail/brake light bulb
1
1
UB1662E0.book Page 63 Monday, April 17, 2017 11:39 AM

8-64
8
3. Insert a new bulb into the bulb holder, push it
in, and then turn it clockwise until it stops.
4. Install the bulb holder (together with the bulb) by turning it clockwise.
EBU25652Removing a wheel1. Place the ATV on a level surface.
2. Loosen the wheel nuts.
3. Elevate the ATV and place a suitable standunder the frame.
4. Remove the nuts from the wheel.
5. Remove the wheel.
EBU36243Installing a wheel1. Install the wheel with the arrow mark pointing in the forward rotating direction of the wheel,
and then install the wheel nuts.TIPFor YFM70KDXJ / YFM70KDHJ / YFM70KPXJ:
be sure to install the nuts with their tapered side
towards the wheel.
1. Wheel nut
1
1
1. Arrow mark
2. Forward rotating direction
3. Wheel nut
1
3
3
2
UB1662E0.book Page 64 Monday, April 17, 2017 11:39 AM

9-1
9
EBU25861
CLEANING AND STORAGE
EBU25882CleaningFrequent, thorough cleaning of your ATV will not
only enhance its appearance but will improve its
general performance and extend the useful life of
many components.1. Before cleaning the ATV: a. Block off the end of the exhaust pipe toprevent water entry. A plastic bag and
strong rubber band may be used.
b. Make sure the spark plug and all filler caps are properly installed.
2. If the engine case is excessively greasy, apply degreaser with a paint brush. Do not apply
degreaser to the wheel axles.
3. Rinse the dirt and degreaser off with a garden hose. Use only enough pressure to do the
job. WARNING! Wet brakes may have re-
duced stopping ability, increasing the
chance of an accident. Test the brakes af-
ter washing. Apply the brakes several
times at slow speeds to let friction dry out
the linings.
[EWB02312]
NOTICE: Excessive wa-
ter pressure may cause water seepage and deterioration of wheel bearings,
brakes, transmission seals and electrical
devices. Many expensive repair bills have
resulted from improper high-pressure de-
tergent applications such as those avail-
able in coin-operated car washers.
[ECB00712]
4. Once most of the dirt has been hosed off,
wash all surfaces with warm water and mild,
detergent-type soap. An old toothbrush or
bottle brush is handy for hard-to-reach pla-
ces.
5. Rinse the ATV off immediately with clean wa- ter and dry all surfaces with a chamois, clean
towel or soft absorbing cloth.
6. Clean the seat with a vinyl upholstery cleaner to keep the cover pliable and glossy.
7. Automotive type wax may be applied to all painted and chrome plated surfaces. Avoid
combination cleaner-waxes. Many contain
abrasives which may mar the paint or protec-
tive finish. When finished cleaning, start the
engine and let it idle for several minutes.
UB1662E0.book Page 1 Monday, April 17, 2017 11:39 AM

9-2
9
EBU27264StorageShort-term
Always store your ATV in a cool, dry place and, if
necessary, protect it against dust with a porous
cover. NOTICE: Storing the ATV in a poorly ven-
tilated room or covering it with a tarp while it is
still wet, will allow water and humidity to seep
in and cause rust. To prevent corrosion, avoid
damp cellars, stables (because of the presence
of ammonia) and areas where strong chemi-
cals are stored.
[ECB00722]
Long-term
Before storing your ATV for several months: 1. Make any necessary repairs and perform all outstanding maintenance.
2. Follow all the instructions in the Cleaning sec- tion of this chapter.
3. Fill up the fuel tank and add fuel stabilizer (Fu- el Med Rx if available), and then run the en-
gine for 5 minutes to distribute the treated
fuel. 4. Perform the following steps to protect the en-
gine from internal corrosion.a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place the spark plug on the
cylinder head so that the electrodes are
grounded. (This will limit sparking during
the next step.)
d. Turn the engine over several times with the starter. (This will coat the cylinder wall
with oil.)
e. Remove the spark plug cap from the spark plug, and then install the spark plug and
the spark plug cap.
5. Lubricate all control cables and the pivoting points of all levers and pedals.
6. Put the frame on stands or blocks to raise all wheels off the ground. (Alternatively, turn the
wheels each month to prevent the tires from
degrading in one spot.)
7. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
Specified amount:
7.5 ml per liter of fuel (1 oz per gallon)UB1662E0.book Page 2 Monday, April 17, 2017 11:39 AM

10-5
10
Handlebar-mounted light:Bulb type:Halogen bulb (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)Bulb voltage, wattage × quantity:Headlight:
12 V, 30.0/30.0 W × 2
Handlebar-mounted light: 12 V, 35.0/36.5 W × 1 (YFM70KPAJ, YFM70KPHJ,
YFM70KPSJ, YFM70KPXJ)
Tail/brake light: 12 V, 5.0/21.0 W × 1
Meter lighting: EL (Electroluminescent) (YFM70KPAJ, YFM70KPHJ,
YFM70KPSJ, YFM70KPXJ)
Neutral indicator light: LED
Fuel level warning light:
LED (YFM70KDHJ, YFM70KDXJ)
Reverse indicator light: LED
Coolant temperature warning light: LED
EPS warning light:
LED (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Park indicator light:
LED
Four-wheel-drive indicator light: 12 V, 1.7 W × 1 (YFM70KDHJ, YFM70KDXJ)
Engine trouble warning light: LED High-range indicator light:
LED (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Low-range indicator light: LED (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Differential gear lock indicator light: LED (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Fuses:Main fuse:40.0 A
Fuel injection system fuse:
15.0 A
EPS fuse: 40.0 A (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Headlight fuse: 10.0 A (YFM70KDHJ, YFM70KDXJ)
15.0 A (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Signaling system fuse:
10.0 A
Ignition fuse: 10.0 A
Auxiliary DC jack fuse: 10.0 A
Four-wheel-drive motor fuse:
10.0 A (YFM70KPAJ, YFM70KPHJ, YFM70KPSJ,
YFM70KPXJ)
Radiator fan motor fuse:
20.0 A
UB1662E0.book Page 5 Monday, April 17, 2017 11:39 AM

12-1
12
INDEX
AAccessories and loading ................................................ 6-5
Accessories, DC jack ...................................................4-24
Air filter element, cleaning ............................................ 8-37
Axle boots .................................................................... 8-48BBattery .......................................................................... 8-53
Brake fluid, changing ...................................................8-44
Brake fluid level, checking ........................................... 8-43
Brake lever free play, checking the front ..................... 8-45
Brake lever, front .......................................................... 4-15
Brake levers, checking and lubricating ........................ 8-49
Brake light switches ..................................................... 8-48
Brake pads and friction plates, checking ..................... 8-42
Brake pedal and rear brake lever ................................. 4-16
Brake pedal, checking and lubricating ........................ 8-50
Brakes .......................................................................... 8-42
Brakes, front and rear .................................................... 5-3CCables, checking and lubricating ................................. 8-49
Carrier, front ................................................................. 4-21
Carrier, rear .................................................................. 4-22
Chassis fasteners ........................................................... 5-6
Cleaning ......................................................................... 9-1
Coolant ................................................................. 5-3, 8-29
Coolant temperature warning light ................................. 4-3DDifferential gear lock, indicators (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ................ 4-5 Differential gear oil ............................................... 5-3, 8-27
Drive lever 2WD/4WD (YFM70K
DXJ / YFM70KDHJ) ... 4-13
Drive select lever .......................................................... 4-16
Drive select lever and driving in reverse ........................ 6-2
EEngine break-in .............................................................. 6-4
Engine oil ....................................................................... 5-3
Engine oil and oil filter cartridge .................................. 8-20
Engine stop switch ......................................................... 4-9
Engine trouble warning light .......................................... 4-3
EPS warning light (for EPS model) ................................. 4-4FFinal gear oil ......................................................... 5-3, 8-24
Four-wheel drive icon (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ........................................ 4-5
Four-wheel drive indica tor light (YFM70KDXJ /
YFM70KDHJ) ............................................................... 4-4
Four-wheel drive switch (On-Command 4WD)
(YFM70KPXJ / YFM70KPAJ / YFM70KPHJ /
YFM70KPSJ) ............................................................. 4-11
Fuel ...................................................................... 4-17, 5-3
Fuel level warning light (YFM70KDXJ / YFM70KDHJ) ............................................................... 4-3
Fuel tank cap ............................................................... 4-17
Fuses, replacing ........................................................... 8-57HHandlebar switches ....................................................... 4-8
Headlight beam, adjusting ........................................... 8-62
Headlight bulb, replacing ............................................. 8-59
UB1662E0.book Page 1 Monday, April 17, 2017 11:39 AM

12-2
12
High-range indicator light (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ................ 4-2
Horn switch .................................................................. 4-10IIdentification numbers ................................................. 11-1
Indicator lights and warning lights ................................. 4-1
Instruments, lights and switches ................................... 5-6LLabel locations ............................................................... 1-1
Light switch .................................................................. 4-10
Low-range indicator light (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ................ 4-2MMain switch .................................................................... 4-1
Maintenance and lubrication chart ................................ 8-5
Maintenance chart, emission control system ................ 8-3
Model label .................................................................. 11-1
Multi-function display (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ....................................... 4-5NNeutral indicator light ..................................................... 4-2OOn-Command drive switch “4WD/LOCK” (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ /
YFM70KPSJ) ............................................................. 4-12
Override switch (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ..................................... 4-10
Owner’s manual and tool kit .......................................... 8-2PPanels, removing and installing ..................................... 8-9
Park indicator light ......................................................... 4-2 Parking ........................................................................... 6-4
Parking on a slope ......................................................... 6-5
Part locations ................................................................. 3-1
RRear brake, adjusting the lever, pedal free play .......... 8-45
Rear knuckle pivots, lubricating .................................. 8-52
Reverse indicator light ................................................... 4-2
Riding your ATV ............................................................. 7-1SSafety information .......................................................... 2-1
Seat .............................................................................. 4-19
Shock absorber assemblies, adjusting the front and
rear (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ /
YFM70KPSJ) ............................................................. 4-22
Spark arrester, cleaning ............................................... 8-39
Spark plug, checking ................................................... 8-17
Specifications .............................................................. 10-1
Speed limiter ................................................................ 4-15
Stabilizer bushes, checking .......... ............................... 8-51
Starting the engine ........................................................ 6-1
Start switch .................................................................. 4-10
Steering shaft, lubricating ............................................ 8-52
Storage .......................................................................... 9-2
Storage compartment .................................................. 4-20TTail/brake light bulb, replacing .................................... 8-63
Throttle lever ......................................................... 4-14, 5-4
Throttle lever free play, adjusting ................................ 8-41
Tires ............................................................................... 5-4
Trailer hitch (YFM70KPXJ / YFM70KPAJ / YFM70KPHJ / YFM70KPSJ) ..................................... 4-23
Troubleshooting ........................................................... 8-65
UB1662E0.book Page 2 Monday, April 17, 2017 11:39 AM